How to Replace Rear Brake Pads in Mercedes-Benz C300 W205 W206 and E300 W213

Подписаться 35 тыс.

Просмотров 186 тыс.

50% 1

How to Replace Rear Brake Pads in Mercedes-Benz C300 W205 W206 and E300 W213
In this video I demonstrate how to change front brake pads in Mercedes-benz C-class and E-class with AMG brakes
Mercedes-Benz How-To videos: • Mercedes-Benz How-To v...
Brake Caliper Spreader tool #ad: amzn.to/2YBGYWb
This video is step-by-step instructions for replacing rear brake pads and rotors on Mercedes-Benz C-Class C300 W205 W206
While the vehicle is still on the ground and with the parking brake on, break free all rear-wheel lug nut bolts. Chock front wheels to prevent vehicle from rolling. Lift the wheel off the ground.
Before removing brake caliper and pads you need to move brakes in Fitting position. Press OK to move to Fitting Position
Remove bolt caps and undo 2 caliper bolts
Detach brake pad sensor and Detach caliper wires
Detach caliper and clean caliper with brake cleaner
Push Caliper piston in using caliper spreader tool
Install new brake pads
Reinstall caliper with 2 bolts. Finish tightening bolts to your vehicle torque spec. For my vehicle: 25 ft. lbs.
Attach caliper wires and attach brake pad sensor
When brake pads are replaced, don't forget to exit Fitting Position
Deals & my Gears on Amazon: www.amazon.com/shop/hummansunson
Disclosure: As an Amazon Associate I earn from qualifying purchases
Disclaimer: This video is for entertainment purpose only! NewRoad assumes No liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Please consult your qualified auto technician

Авто/Мото

Опубликовано:

25 июн 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 199

@NewRoad 4 года назад

Mercedes-Benz How-To videos: ru-vid.com/group/PLLoEAO8f1zNwqR2KEyXCjGCkuOrxGGNfL

@darthtyranus7683 2 года назад

Question part# for brake pads?

@Ahmedpakido Год назад

I figured out how to get to that menu but I couldn't get the video of it so using your clip off that if that's OK with you?

@NewRoad Год назад

@@Ahmedpakido Please don't copy any videos - you may get copyright strike

@Ahmedpakido Год назад

@@NewRoad im not copying the whole video just the clip where you mentioned how to get to the settings if that's ok?

@NewRoad Год назад

@@Ahmedpakido Please don't

@spineguy1553 11 месяцев назад

Great video. For an amateur a couple things to consider. In your brake set. Where the sensor will click in. You will put those pads on separate sides. If you have a large C clamp. Use the old brake pad put it on top of the caliper and use the c clamp to compress the cylinder in. If you don’t have the tool in video. If you don’t have a 7mm. Use a T45 works perfect. Just changed my rear brakes in less than 40minutes.

@kevinrjoyce8954 3 года назад

I've got a 2019 C Class 220D. Independent garage said they needed a code to do rear pads which they didn't have. I had a Renault which was a doddle to do - wire from the battery and it wound the calipers back for you. Thanks for the video. Very well filmed and clear. 👏

@MrGeo19792000 2 года назад

Hi!!! Thank you for doing this video. I was so overwhelmed i was about to pay $400 to $800 To change the rear brakes on my 2016 C300 but luckily I ran into your video and now o.k. know how to change them. THANK YOU YOUR VIDEO WAS VERY VERY HELPFUL! hope you make more.

@NewRoad 2 года назад

I'm glad it was helpful. It is actually very easy to maintain C300 - I made many videos that can help you save thousands of dollars - take a look at this list: ru-vid.com/group/PLLoEAO8f1zNwqR2KEyXCjGCkuOrxGGNfL

@gsanchez922 2 года назад

Lol I went today for service and they want around $700 for rear brakes

@cadillacnick8533 Год назад

So u didn’t have to change the rotors on the rear ????

@mcronnyvv 2 года назад

So apparently I am “special needs” the parking brake went on automatically LMAO. Thank you AGAIN FOR ALL THE HELP YOUR ARE AWESOME!!

@gabrielroom 3 года назад

You are awesome! My brake pads will need to be replaced soon but I don't have the guts to do it by myself...

@NewRoad 3 года назад

You can do it! It is not that hard

@mcronnyvv 2 года назад

Thank you, I am positive you have prevented me from causing myself a lot of grief again TY

@NewRoad 2 года назад

Glad to help

@mcronnyvv 2 года назад

I got it thanks to this video

@kernelleap9915 11 месяцев назад

Sooo many helpful details without a single spoken word! Great video!

@NewRoad 11 месяцев назад

Glad it was helpful!

@johnrowson6856 3 года назад

Thanks guys , excellent video . Learned on on side . Other side took a matter of minutes to do .

@NewRoad 3 года назад

Glad it helped!

@jennifervincent784 Год назад

This video was excellent! Thank you so much. Very well filmed, and great detail. 👍

@NewRoad Год назад

Glad it was helpful!

@TheMingilator 2 года назад

Is it advisable to pump out that pistons with the brake pedal before de activating fitting mode

@georgeyounger1 Год назад

Wow that is easy the most important thing is the fitting position, thank you very much you are a great help, that was a great job you did on the brakes as well as simple detailed instructions

@NewRoad Год назад

Glad it helped

@gregorioloya4905 7 месяцев назад

Great video. Very helpful well documented and with very good information. Thank you very much.

@NewRoad 7 месяцев назад

Glad it was helpful!

@luisgomes756 4 года назад

Very good and clean service!

@NewRoad 4 года назад

Thanks

@qasimhussain8489 2 года назад

Great video eazy shown and helped me proper thanks mate keep up the good work

@NewRoad 2 года назад

Glad it helped

@snazzysteveT Год назад

Great video, clear, detailed👏thanks for the help.

@NewRoad Год назад

Glad it helped

@yes-man1112 Год назад

Nice Video! Very helpful! I will try to replace my brake pads of my C200.

@NewRoad Год назад

Glad it helped!

@giantpro1 9 месяцев назад

Fantastic video very informative and to the correct instruction. ❤

@NewRoad 9 месяцев назад

Thank you

@louisamotsepe2828 Год назад

Thanks for yr demonstration.

@Ahmedpakido Год назад

Thanks for the video. Going to change brake pads in my uncles car

@orlando1340 Год назад

Great video thank you. . What size lug nut key did you use for the wheels?

@NewRoad Год назад

Socket 17mm

@francyroger653 9 месяцев назад

Thanks for this video.

@NewRoad 9 месяцев назад

You're welcome

@catanijkjk4004 3 года назад

Hi mate nice job! When we change the break pads do we need to exit fitting position for every wheel or just once for all of them?

@NewRoad 3 года назад

Set once and complete all wheels

@amjadkhan-jv6xj 2 года назад

I watch these videos just to listen to the noise of tools.

@normarathon9117 3 года назад

AWESOME VIDEO

@NewRoad 3 года назад

Thanks!

@Robert_Hall90 2 года назад

Hiya mate do you need to pump the pedal to bring the pistons out before exiting the mode or does exiting that mode use the electric hand brake motor to wind the pistons back?

@NewRoad 2 года назад

Exit the mode and pump the brakes to test it and make sure all good

@ANTONIORAMIREZ-lu3ij Год назад

Excelente documento gráfico.

@1tapster Год назад

great video, thanks for posting

@NewRoad Год назад

Glad it was helpful

@steven__7009 2 года назад

Where do you get pads? I was going to get a new set of pads for front and rear, and rotors for the front as well. Any recommendations?

@NewRoad 2 года назад

Most of my parts I buy from rockauto.com, and usually go with BOSCH or ACDELCO

@nadirbedad5210 Год назад

Thank you 👍

@eliasbubbe 4 года назад

Apparently I'm notification squad? Nice video btw!

@NewRoad 4 года назад

Thank you for watching!

@jasonschmatt6825 10 месяцев назад

Thank you for this.

@NewRoad 10 месяцев назад

Glad it helped

@KraftySkillz 3 года назад

I have an E-class W213 220D, i take it that applies to mine as well? Also, spoke to an indie and he said that the caliper would need calibrating as its electronic, any truth to this? I want to give this a go myself.

@NewRoad 3 года назад

Go for it. When brake pads move back to fitting position - it calibrates itself. I changed both, front and rear pads, and no problem or messages

@abdalymahmud9136 3 года назад

Very simple tanks

@tahir1156 6 месяцев назад

Amazing and informative video

@NewRoad 6 месяцев назад

Glad you liked it

@weepz Год назад

Where was you able to find your torque specs? All I can seem to find online is Wheel nut torque specs. :(

@JavierMartinez-vx1dp Год назад

Thanks, my friend, for the video help a lot . 🙂👍

@NewRoad Год назад

Glad it was helpful!

@williamtorres4214 Год назад

I have a 2016 MB c300 after the whole break pad change and everything is done do I need to bleed the break or just out the wheel back in and take it off fitting mode and that’s it

@NewRoad Год назад

You don't need to bleed brakes if you just followed this video. Take it off fitting mode and press brake pedal few times until it's firm - and you good to go. You need to bleed brakes if you change brake caliper or it is time to flush brake fluid as per maintenance: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-vHhqcs2SJKQ.html

@stanleykania7184 Год назад

Thank you

@abraju 2 года назад

Beautiful tipc

@TheFrenchPug 3 года назад

Very well done and edited video. Not counting video recording, how long to do back axle?

@NewRoad 3 года назад

Thank you. Under an hour is enough to complete the job

@TheFrenchPug 3 года назад

@@NewRoad That's not bad at all then. Thank you.

@dmitryo6649 2 года назад

Thanks a lot. Very helpful and clear directions. Can you please give more information about Brake Lubricant. Is it sort of ceramic paste (anti-squeal brake paste) or is it lube (longlasting fett). Rest is clear for me. Thanks a lot again! I would try on my MB C300 S205 very soon. Systems looks the same. Braking pads are already delivered to me. Just have to find time.

@NewRoad 2 года назад

Yea, should be the same and easy to do. I use this one amzn.to/3kb82WE

@garagesociety9907 8 месяцев назад

Great video.

@NewRoad 8 месяцев назад

Thanks!

@timelessestates4946 3 года назад

Would the same setup go for a 2019 glc300? And is the caliper piston spreader too required?

@NewRoad 3 года назад

You should be able to change on your glc as well by just following this video, and yes - it is good idea to get spreader, it makes the job much easier and it is not expensive: amzn.to/2YBGYWb

@robertlasater2609 2 года назад

GOOD VIDEO MATE.....WHATS THE WHEEL LUG TORQUE YOU USED THERE?

@NewRoad 2 года назад

If you have operator's manual the spec should be in Wheels and Tires section. Mine is 2017 C300 and it says - 96 lb-ft (130Nm)

@jan-willemvandenberg1769 Месяц назад

Very useful

@NewRoad Месяц назад

Glad to know that video helps

@syarifhidayatullah5328 3 года назад

9:10 I Love that wheel 😁

@alltech3987 Год назад

Good job bro

@NewRoad Год назад

Thanks

@jobjose6539 11 месяцев назад

Thanks bro...

@NewRoad 11 месяцев назад

Welcome

@305_beatbox4 3 года назад

Thanks for this video this made a 2 hour job to less than 30 minutes 🙏🏽👌🏽✊🏾✊🏾💯

@NewRoad 3 года назад

Glad it helped

@REAHT 4 месяца назад

Do you need two sensors for rear brakes or only on one side ?

@NewRoad 4 месяца назад

One on one side

@joaopauloventura372 Год назад

Toppppp 👏🏼👏🏼👏🏼

@JK-dx5ts Год назад

after you have put the car in the 'fitting position' do you have to leave the car on?

@NewRoad Год назад

no, you can shut down

@jgomez7822 Год назад

So on a Mercedes the fitting position when you're done you exit it's basically pumping the brake fluid for you instead of you doing yourself correct?

@jgomez7822 Год назад

Like when you change your brakes on a Honda afterwards you close the brake fluid cap and you pump the brakes with your foot with the Mercedes it does it on its own when you exit position correct

@NewRoad Год назад

It's always good idea to pump it

@nick6834 3 года назад

What year and make is this particular car your working on?

@NewRoad 3 года назад

This one is 2017 C300

@williamtorres4214 Год назад

Do you need to bleed the brakes ? Or would it be good after all that ?

@NewRoad Год назад

If you are replacing just pads - you don't need to bleed brakes. Here is full maintenance schedule for Mercedes which indicates when to bleed brakes.

@kerm281 5 месяцев назад

May I know what happens if you changed your pads without going to the fitting position? What will happen ? Great vid btw thanks

@NewRoad 5 месяцев назад

You won't be able to pull out rear pads

@mickivanov 2 года назад

The car should stay with ignition on all the time while performing the procedure... or we can switch off the ignition ?

@NewRoad 2 года назад

I left it on

@user-ht4pz1by9z 8 месяцев назад

do i have to set it to fitting position twice for both sides or once for both side?

@NewRoad 8 месяцев назад

You set once as in video and exit when done all brakes

@safadadon3484 5 месяцев назад

So basically leave on fitting position before you press ok you do both sides first

@glogang6419 3 года назад

Do I have to move brake to fitting position on a 2013 C300 4matic

@NewRoad 3 года назад

Yours is W204, right? No since it doesn't have electronic parking brakes

@glogang6419 3 года назад

@@NewRoad yea it’s a w-204

@davidstadulis3356 Год назад

Are front and rear rotors the same on a 2016 C300 AWD non AMG? MBUSA only shows one part number. Thanks.

@NewRoad Год назад

I'm not sure to be honest. You can also check fcpeuro.com and rockauto.com to see more choices

@cadillacnick8533 Год назад

Do u have to change the rotors if there not bad when changing the breaks

@NewRoad Год назад

@@cadillacnick8533 You don't need to change rotors if they are ok

@romanwhitt1804 2 года назад

Will this work for a 2018 AMG C43 Coupe?

@NewRoad 2 года назад

Yeap, it should - you might even have the same brakes as in video, since it is AMG package

@hassan150 11 месяцев назад

I have a 2020 W205, where do I find out the torque specification for wheels or calliper bolts? Great vid!!

@NewRoad 11 месяцев назад

I would assume since it is the same (W205) it should be the same, but double check with Mercedes dealer

@hassan150 11 месяцев назад

@@NewRoad thanks, is there a specific website you used for the torque specifications?

@youngdee8826 2 года назад

After replacing the brakes I pressed ok but before I did the other side do I have to start the process over?

@NewRoad 2 года назад

Yes, you need to move to fitting position

@1tapster Год назад

exactly what i was looking for, glad i can learn from your mistake instead of making it. Thanks

@rakun1212 3 года назад

Why didn’t you clean and lube the slide pins while you had this apart?

@NewRoad 3 года назад

Mine was clean and in good condition - but it is a Good idea!

@storm_merle_ 2 года назад

What size is torch to take off from brakes

@NewRoad 2 года назад

If it's not in a video, I will have to check and post in description. Sorry for that

@fitnesswithsteve 3 года назад

Does it void the warranty if you change the pads and rotors yourself?

@wongtanakanguyensmithlopez 3 года назад

Yes. If you are a licensed mechanic then no.

@arwinvinnysardana3266 3 года назад

No: www.consumer.ftc.gov/articles/0138-auto-warranties-routine-maintenance#do

@o0Guns0o 3 года назад

What is the purpose of the metal clips on the brake pad, next to the wear sensors? Is it to apply pressure to the pads onto the calipers to prevent rattling? Is it only used on the inside pad?

@o0Guns0o 3 года назад

5:30

@tha_sarge 2 года назад

I'm having an issue with my parking brake not disengaging 😞😞 please help

@NewRoad 2 года назад

Try to follow exact steps as in the video, I never had this problem

@melissawelborn5155 2 года назад

Is the 2017 C300 done the same way?

@NewRoad 2 года назад

The vehicle in video is actually 2017 C300 🙂.

@MrALEMARPONGOS 2 года назад

Is this one will work on c43 amg 2018?

@NewRoad 2 года назад

Yes, same process. Easy to do, just make sure you have proper tools before you start

@MrALEMARPONGOS 2 года назад

@@NewRoad Do you need to leave the ignition on while doing the brake pads?

@MrALEMARPONGOS 2 года назад

@@NewRoad It’s not working on my c43 2018.

@jovanneclaro8639 3 года назад

Is it the same process for front brakes?

@Bdawgsmaknu 3 года назад

Rear brakes. Stated in the title as well.

@NewRoad 3 года назад

Similar, I haven't done mine front yet

@josealerma999 3 года назад

It a little easier since there’s no need to put vehicle into “fitting position” due to parking brakes only being in the rear

@baltimoreboomin 2 года назад

Which year benz is this

@NewRoad 2 года назад

This is 2017, which has AMG & Night package

@mr-dpc-5018 4 года назад

GOOD VIDEO BUT I THINK YOU SHOULD HAVE MENTIONED ABOUT TORQUING THE WHEEL STUDS UP.

@NewRoad 4 года назад

Thanks, agree - any additional info never hurts

@Ahmedpakido Год назад

Doesn't show up any screen after holding ok button and call button in 2016 mercedes c300

@NewRoad Год назад

follow exactly as in video, phone button first and within second ok

@kechsimo3433 Год назад

Merci merci boukou anpikable

@albertdalmau7501 Год назад

Is their a reason when I click the ok and call button the setting doesn't appear

@NewRoad Год назад

try few times, sometime timing is off

@graytat 3 года назад

What do you do if the parking brake is flashing and wont work after? I followed everything step by step.

@NewRoad 3 года назад

Did you exit fitting position after you complete everything?

@graytat 3 года назад

@@NewRoad yes, but it said unable to perform task.

@safadadon3484 5 месяцев назад

@graytat did you ever fix the problem?

@dmitryo6649 2 года назад

Perfect, followed step by step and replaced rear break pads successfully. I have model 2019. It was a bit complicated with putting breaks into "service mode". I had to put my car into N gear before "conditions for service of breaks" can be fulfilled. But besides this all the same. Great video, thank you very much. Managed within 1h both rear pads.

@NewRoad 2 года назад

Glad it helped

@weepz Год назад

Intresting, I have a 2018 model, so I'll have to remember this, is it possible to stay in N with the engine off?

@dmitryo6649 Год назад

@@weepz I have keyless start. While I was in service mode I could not switch ignition off. So think about battery. You can put in N and turn engine off. Just put anti-rollers under your wheels.

@weepz Год назад

@@dmitryo6649 noted, will try that. Cheers 👍🏻 🍻

@MaclineROONEY-vz6no 8 месяцев назад

Good afternoon am new here

@NewRoad 8 месяцев назад

Welcome to the channel. If you own Mercedes-Benz - you might want to bookmark this playlist of How-To videos for Mercedes: ru-vid.com/group/PLLoEAO8f1zNwqR2KEyXCjGCkuOrxGGNfL

@deepakbains1842 3 года назад

So I don't need a scanner/obd reader?

@NewRoad 3 года назад

You don't need odb reader to replace your brake pads

@deepakbains1842 3 года назад

@@NewRoad thanks!!!

@deepakbains1842 3 года назад

@@NewRoad I'm not able too push back the piston?

@NewRoad 3 года назад

Did you follow video and moved brakes to fitting position?

@jhholl 3 года назад

@@NewRoad I am not able to get that service menu on my 2015 c300 by pressing both the phone and ok button at the same time for 10 seconds. Is there an alternate way or should I just use the brake caliper tool that both depresses and turns the caliper to depress it?

@scottsoriero9827 2 года назад

I have been a mechanic for over 45 years and have done so many types of brakes over the years its not funny. I am not criticizing and I appreciate anyone who puts up how to videos, I'm just asking. Why didn't you service or replace the rotors? I know the pads will seat, but they will also initially wear very rapidly and will cause some break squeaks down the road. Plus, and most annoyingly will without a doubt cause some brake shuttering when braking hard. Just a thought. Thanks for the video.

@NewRoad 2 года назад

Appreciate your feedback. Rotors were less than 3 years old with low mileage, and looked good to me. It's easy to replace them anyway if required. So far, mine C300 drives like new (knocking on wood)

@cadillacnick8533 Год назад

I just bought some new break pads for the rear and they look good so I’m try putting on my break today

@maankhaira5517 2 года назад

What’s the point of using the spreader? Sorry just trynna learn how to do this hahaha

@NewRoad 2 года назад

Old pads are thinner than new pads - so you need to create space for new pads

@neverontime 3 года назад

Why is there a sensor in the brake pads? What happens when you hit that on the menu? I was looking to do this for a friend but I've never seen this crazy shit

@NewRoad 3 года назад

It is wear sensor - tells you when to replace your pads. Nothing special - just follow the steps in video.

@af9126 3 года назад

very similar to bmw e90 🤔

@howtofixit9605 Год назад

What year is this for

@NewRoad Год назад

W205 - 2014 and 2021, and the same for W205 from 2021

@williamtorres4214 Год назад

@@NewRoad is it necessary to bleed the brakes after all this or is it fine ?

@williamtorres4214 Год назад

@@NewRoad I have a 2016 MB c300 after the whole break pad change and everything is done do I need to bleed the break or just out the wheel back in and take it off fitting mode and that’s it

@williamtorres4214 Год назад

@@NewRoad if you can please answer 🙏🙏🙏🙏