How to Set Camshaft Timing // 1.4 Sonic & Cruze

Подписаться 37 тыс.

Просмотров 20 тыс.

50% 1

Our Install Technician, Ryan takes you through his process to properly set camshaft timing on 1.4 Sonics or Cruzes. This demonstration is on a Cruze but the process won't change on a Sonic. Ryan will show you how to time stock cams as well as our ZZP Stage 1 Cam. Please do NOT attempt if you do not have cam timing tools or a torque wrench.
0:00 Intro
0:33 Timing Tools
1:27 Stock Cam Timing
7:20 Torque Specs and Procedure
10:13 ZZP Stage 1 Cam Timing
11:46 Torque Specs and Procedure on ZZP Cam
14:30 Final Tips and Reminders
15:40 Outro
GOFASTNOTBROKE
#howto #timing #timingmatters #chevy #generalmotors #sonic #cruze #camshaft #carmodification #automotive #installation
ZZP is located in Wyoming, MI. We are the world’s largest supplier of aftermarket performance parts for 3800, Sonic/Cruze, Ecotec, and ATS platforms, providing industry-leading customer service and support.
Our staff of professionals has experienced knowledge in all the vehicle platforms we represent. ZZPerformance is dedicated to 100% customer satisfaction. We provide you with highly specific technical information, that can’t be found anywhere else.
Interested in modding your car? Check out our parts at zzperformance.com
Questions about modding? Email us at customerservice@zzperformance.com

Авто/Мото

Опубликовано:

13 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 27

@rome8087 7 дней назад

Hey guys! Be sure to listen to what he's saying when it comes down to the camshaft actuator phasers. Pay very close attention to that part! When it's time to torque those actuator bolts, be sure to hold the 22mm wrench with the same amount of pressure. Be sure when you're tightening the bolt to spec, don't let the camshaft move the chain, or else the crankshaft tool will move out of place, and the timing will be off. Keep paying attention to the crankshaft tool everytime you're done tightening either camshaft.

@kezdolbeck2881 2 месяца назад

Guys thank you for the thorough video. I did this job for my wife's cruze and didn't realize the press fit phaser. She does absolutely have both cam correlation codes active rn and shes been complaining oh my god i cant use my remote start when the check engine lights on please fix it. Now I get to be a cool husband and do it right.

@InTheCoupeWithCoop 5 месяцев назад

Right tools for the job and makes it simple!

@Tater4200 19 дней назад

Beautiful video. To the point.

@hagensperry119 5 месяцев назад

I’m wondering if this video was purposed because of me lol I didn’t have my new intake cam exciter set in the right spot easy fix car has been absolutely ripping since I reset the timing! Highly recommend the zzp stage 1 turbo cam. Also highly recommend taking your time when installing

@Flyjango1 2 дня назад

How do you adjust the slack on the actuator while under the locking tool? clock wise, counter clockwise or TDC ?

@edgarflores332 5 месяцев назад

Whats the dice number hes using on the bolts of cams actuators with the torque wrench ?

@justinwilger2861 3 месяца назад

If I follow these steps upto the locking out of my camshafts, can I remove the large bolts and replace the sprockets to my camshaft actuator? They sell the chain kits with these and water pump, but I've seen none cover this step.

@ZhmiKnopa Месяц назад

4:20 Question: when I insert my cam lock tool, the exhaust valves on cylinder #2 are slightly open. I have to twist the exhaust cam clockwise with some pressure to get the slot flat at the back end of the cam, since the cam lobes are opening the valves when I turn it. Does this mean something is wrong? Also, I bought the cheapest timing tool set and the cam locking plate barely fits in the grooves. I had to tap it in with a small hammer, seems like it should be thinner. I recommend a quality set if you can afford it.

@josephjorgensen4853 4 месяца назад

You are a lifesaver.

@chrislink8726 7 дней назад

Question. Doing a head swap and a stage 1 swap. I timed my actuators with the tool but didn't check the crank. If i replace the head and all new components as long as #1 is TDC and locked with the pin can i just time it as shown here?

@ytpro9405 3 месяца назад

Hi man here. Very thorough. Thank you.

@justinwilger2861 3 месяца назад

Not the 1.8, but the 1.4L turbo like in your video. When you get a chance to reply. Thanks

@BenDover-wu6lu 2 месяца назад

Do you have a part number for your holding tool? The one that came with my kit does not fit.

@ZhmiKnopa Месяц назад

My cam holding tool barely fits, I had to tap it in. Maybe sand it down a mil or two

@BenDover-wu6lu Месяц назад

@ZhmiKnopa my brother sanded it down for me.

@y33sean 5 месяцев назад

Anything different for a twin intake cam setup? 🤔

@The_Mod_Scientist 5 месяцев назад

No, same as the Stage 1/ZZP Tool procedure

@ryannewnham8826 5 месяцев назад

Do you get a lumpy idle with this

@ZZPerformanceChannel 5 месяцев назад

From just installing the cam you do not get the typical "cam" sounds because it is a VVT car so the PCM compensates for the difference. However, your tuner can likely get you a little of that noise with the tune.

@ryannewnham8826 4 месяца назад

@@ZZPerformanceChannelwould this need to be mapped in

@sazzyPheox 5 месяцев назад

that thumbnail tho

@richardwiley9025 3 месяца назад

I have done step by step and now my car won’t start and makes a weird noise.

@user-yr9bx6fy3q 2 месяца назад

You prolly got top dead center on the second rotation. There’s 1 that’s intake rotation which is the one needed, then there’s 2 exhaust rotation which I assume is the one you did. You need to redo whole thing and make sure it’s on the intake rotation.

@jimiburgess6434 4 месяца назад

I am going to make you sad. Why did I have to manually move my cam sprocket to get it to run? You guys do all these videos and I have searched high and low for reference but exactly where does the sprocket go on the cam? There are timing marks, and it does matter!

@Deesfilms 5 месяцев назад

While this video is extremely helpful? You didn’t actually show how to take the chain off to replace the timing chain. This is a critical step and I don’t know how to do it with that lock on the actuators.