How To Setup H100-2.2T4 Chinese VFD Inverter for 2.2kW Spindle 400Hz 24000rpm 380V 

Recently I have successfully converted my CNC that have the exact same VFD from manual spindle speed control to USB/MACH3 spindle speed and direction control. - I used a DC-DC converter to lower the 12V VFD power supply ( P12 port ) from 12V to 10V and then wired it to the 10V port on the board : - I wired the AI1 to AVI - I wired the GND to ACM Then I used a 2 channel 24V relay module to control the spindle : - I powered the relay directly from the board, connecting the VCC from the relay to the 24V port and the GND from the relay to ACM from the board. - I connected the In1 pin on the relay to the Out1 port on the board - I connected the In1 pin on the relay to the Out2 port on the board - I connected the X1 and the GND port on the VFD to the relay first channel (first 2 outputs while facing the relay upwards) - I connected the X2 and the GND port on the VFD to the relay second channel (first 2 outputs while facing the relay upwards) That's the missing part of wiring in the video, just follow the function parameters ( F001 = 1, F002 = 2). For the MACH 3 pins, I just downloaded the XML file from the build your cnc website. Here is the link: buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board Happy CNC machining.

Good afternoon. I would like to congratulate you on your work. I bought this spindle and the same inverter. I've already managed to turn it around. but I was unable to connect with Mach3 as you did. I could make another video showing how to connect the cables inside the inverter and in the mcah3.

Buen día ; muchas gracias por el trabajo que realiza. Tal vez podría ayudarme? Configuré el motor según las especificaciones del video pero al encenderlo debo retirar una plaqueta negra en el interior para que inicie punto y coma además no se puede modificar la velocidad con el botón manualmente; sabe cuál es el problema y cómo solucionarlo? Muchas gracias por su ayuda.

It is strange, because I find that several items you bought I also bought the same like the vfd and the ac servo. Which are not common in the internet cnc users. I bought the same vfd (220 single phase) , I have 2 questions I supplied 220 volt single phase and started the motor right away. Everything went fine. Later I was setting the parameters, I noticed that the motor voltage parameter was set to 380 volt. So I changed it to 220. first question : The inverter should not have capability to supply 380 if it is fed single phase 220. Could it? I mean it is an inverter not transformer. So even the setting for the motor voltage were at 380, the actual voltage supplied to the motor was 220 v. Otherwise, the motor could have burned. Second question which vfd pin is for M5. Or how do I externaly shut the spindle off. Is the mach3 or linuxcnc user interface for spindle-off fed to the vfd and to which vfd pin? Thanks for this good video Philip

can ask please? where you put a avi wire from red bob to the hs100 inverter

Gracias por contestar, pero si se puede, hay que poner una resistencia haciendo puente. Hay un video de mi targeta. Controlar spindle con akz250.

hola, tengo el mismo VDF, seria posible me indicaras como conectar un potenciometro para controlar el VDF.muchas gracias por compartir

Tengo el variador de 1500w y la placa akz250, no consigo hacerlo trabajar, problema, no se las conexiones de la placa al variador. Haber si me podeis ayudar.

Buenas, no tiene relé, la targeta he conectado, la salida PWM al Al1, gnd con gnd del variador, forward en el pin 4 y una resistencia de AO al Al1. Me funciona, lo que me ocurre ahora es que demora mucho tiempo en alcanzar las 24000 revoluciones. A qué puede ser debido? Lo mismo no lo tengo bien conectado.

Hello. I would like to ask for your help. How to connect this frequency converter to the NVEM V2 motion controller. Thank you in advance for your answer.

NICE VIDEO, BUT YOU FORGOT ABOUT SETTING THE JUMPS?, WHAT ARE JUMP SETTING?

Alri bro. I'm back. I was looking through some of ur videos and I found this one. I have one of these. I got it off Amazon for 30 Euros. 2.2kw 380V VD.. I don't know how to set these up so this will hopefully help me a little. Nice one. This is the 1st video on this one I've found man so thanks.. haha Salute from DUBLIN. So can I ask why there are 3 phase and single phase VFD's ? What's the difference in a way I could understand. I don't have ur knowledge about these things... I think I need to study more about CNC's bcos I'm going to attempt to build my own soon. If u can give a little advice I'd be grateful. Thanks bro..

hello, I have a G-PENNY H100 -2.2-1B VFD and I don't know how to reverse the direction of rotation on startup. it turns counterclockwise. what parameter should I change? thank you

Hola, tengo el mismo VDF pero cuando lo pongo a funcionar el variador no envía la frecuencia máxima de 60 hz, envía una frecuncia de 20 luego aumenta a 22 luego a 24 y nunca llega a los 60 Hz que necesito, alguna idea al respecto.

Saludo hermano una consulta tengo ese mismo variador, ese variador se puede poner que encienda automáticamente cuando llegue la energía sin la necesidad de presionar el boton run?

can anyone tell me what is the resistance of the brake resistor that can be connected to the DC+ and DB pins. And how to activate this function in the main menu?

I have one question. Did you connect the inverter's 12v output to the mach3 board 10V?

HOLA he conectado todo perfectamente igual a lo del video pero al encender el vdf queda con un valor inicial y sube y baja la frecuencia unos 25hz

Si el mismo

Lo intentado varias veces, si me das algún consejo, aunque tú creas que es mala práctica, no me importa.

Can i get the manual of the vfd bro

can this vfd show rpm instead of HZ

El autor del video Martin Barfoed

Hallo, kannst du mir helfen bei der Programmierung?

You are presenting all the infomation toooo fast for learning anything.

Bloody Gumby Music Really😂