iNav Mission Control for Fixed Wing ✈️ How to and Demo Autonomous Waypoint Mission 🤖

Подписаться 12 тыс.

Просмотров 20 тыс.

50% 1

🔥 🔥 🔥 🔥 FULL SETUP AND LINKS IN DESCRIPTION BELOW ⬇️ ⬇️ ⬇️ (Click 'SHOW MORE'👈🏻 )
How to setup and use Mission Control in iNav to send your fixed wing on an autonomous waypoint mission. I’ve been playing around with this on my AR wing over the last couple of months and it works really well, there are just a few things you need to look out for that will most likely cause you frustration if you don’t watch this video first.
IMPORTANT NOTE: Please make sure your plane flies well in an autonomous mode such as RTH before attempting a WP mission. I recommend higher altitude and close range for your earlier tests. Good luck! :D
When NOT selecting RTH at end of mission: Tested this and the plane will loiter around the final WP at the altitude you had set for that particular WP.
Two things to note or slightly correct from this video:
1: It appears that the target speed may not be used at all in WP missions and it actually uses the 'cruise throttle' you have set for autonomous flying, even though The wiki states: "The mission is defined with waypoints, which have the information about latitude, longitude, height and speed between the waypoints". It's a real shame they have said this in the wiki and added the ability to set the speed per WP because this just causes confusion :/
2: The nav_wp_safe_distance actually stops you from arming if the first WP is further than your parameter, rather than stopping you from entering WP mode while flying as I suggested. However, there is a request to change to behave in the way that I've detailed: github.com/iNa... The reason I missed this was I accidentally had my nav_extra_arming_safety set to 'OFF' so the check on arm was not taking place.
AR Wing Diff ► tiny.cc/AR900Diff
Full WP flight video: coming soon
CLI mentioned in this video:
-nav_wp_safe_distance = First waypoint in the mission should be closer than this value [cm]. 10,000 (100m) default. Set to 0 to bypass this check.
-nav_wp_radius = Waypoint would be considered reached if plane is within this radius. Default 100 = 1m
-failsafe_mission = If set to OFF the failsafe procedure won't be triggered and the mission will continue if the FC is in WP (automatic mission) mode
☕️ 👋🏻 Hey, thanks for watching! If you enjoyed this video or found it useful and would like to show your appreciation/support for my channel, why not buy me a coffee :) ► tiny.cc/BuyAdam...
🔵 Follow me on my Facebook page for updates, build logs, chat, random pictures & vid clips that don't make it to RU-vid: / adamgdoesfpv
📷 Follow me on Instagram @adamgdoesfpv ► tiny.cc/AdamGon...
Sites I get my awesome FPV goodies from:
✅ Banggood ► tiny.cc/Banggoo...
✅ RMRC ► tiny.cc/RMRC
✅ AtomRC ► tiny.cc/Atom-RC (Use coupon 'AdamGdoesFPV' for $10 off)
✅ Amazon ► tiny.cc/Amazon-FPV
✅ HobbyKing ► tiny.cc/HobbyKing
========AR Wing Setup========
In the Air:
-AR Wing - Kit (version I have) ► tiny.cc/ARwingKit
-AR Wing - PNP with electronics and ply winglets (version I don't have) ► tiny.cc/ARwingPNP
-FPV cam (16:9) ► tiny.cc/62gv0y
-2200kv motor ► tiny.cc/t4gv0y
-6x4 prop ► tiny.cc/u5gv0y
-RC Timer 30a ESC ►tiny.cc/rfiv0y
-3S 4000mAh Multistar 10c ► USA link: amzn.to/2zsMtYQ - UK link: amzn.to/2ypGDat
-Matek F405 FC ► tiny.cc/F405
-8M M8N GPS ► tiny.cc/wwyh7y
-FrSky Rx ► tiny.cc/ubl96y
-5.8ghz Video transmitter ► tiny.cc/3wiv0y
-Rear LED's ► tiny.cc/wxiv0y
-Foxeer Lillipop Vtx Antenna ► tiny.cc/Lollipo...
-HD Camera, Runcam 2 ► tiny.cc/k4cv0y
On the Ground:
-Taranis ► tiny.cc/f6cv0y
-Eachine Diversity Monitor with DVR ►tiny.cc/ehfv0y
-Foxeer 5.8 antenna ► tiny.cc/Foxeer5...
-VAS 5.8g Pepperbox ► tiny.cc/VAS5g8P...
========3D Printing Equipment========
-3D Printer ► tiny.cc/qql96y
-PLA filament ► tiny.cc/EryonePLA
-TPU filament ► tiny.cc/Sainsma...
-PETG filament ► tiny.cc/Sainsma...
-Digital Calliper ► tiny.cc/Digital...
========Build equipment========
-E6000 glue ► tiny.cc/E6000Glue
-Laminating Iron ► tiny.cc/Laminat...
-Laminate ► tiny.cc/laminate
-Hot glue gun ► tiny.cc/HotGlueGun
-Foam Cutting Tool ► tiny.cc/vxgv0y
-Heat Gun ► tiny.cc/Adjusta...
-Watt Meter ► tiny.cc/WattMeter
-3M90 spray adhesive ► tiny.cc/3M90adh...
========Other Video Equipment========
-Macbook Pro ► 🇺🇸 tiny.cc/Macbook... 🇬🇧 tiny.cc/Macbook...
-External Hard to Store Final Cut Pro X projects ► 🇺🇸 tiny.cc/Seagate... 🇬🇧 tiny.cc/Seagate...
-Computer Mic ► 🇺🇸 tiny.cc/AU-GM30...

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 207

@AdamGdoesFPV 4 года назад

UPDATE: Please read the two minor corrections to my video in my video description. IMPORTANT NOTE: Please make sure your plane flies well in an autonomous mode such as RTH before attempting a WP mission. I recommend higher altitude and close range for your earlier tests. Good luck! :D

@AidanMacnamara777 4 года назад

Tx for the video, it inspired me to try flying a mission, which I did a few minutes ago, successfully. I was just watching the FPV video back, and even though the speed did take a while to match, it did seem to get to my desired speed, eventually, and then maintain it. That might have just been coincident. Will try it again tomorrow.

@philthayer4087 4 года назад

RTH speed changes once you load a mission. Cruise set at 1550 perfect without mission. Once you load a mission and use RTH 1550 is too slow. With 2.5 anyway.

@AdamGdoesFPV 4 года назад

Aidan, that's great to hear :D cheers!

@AdamGdoesFPV 4 года назад

Hi Phil, I haven't noticed any issue with my RTH speed when using a mission and as I mention, I always use RTH at the end.

@charlesmarseille123 2 года назад

just made my first inav wp mission following your instructions. Thanks!

@AdamGdoesFPV 2 года назад

Glad I could help! Enjoy :D

@AdamGdoesFPV 4 года назад

TEST COMPLETE: When NOT selecting RTH at end of mission the plane will loiter around the final WP at the altitude you had set for that particular WP.

@charlesmarseille123 2 года назад

And it will still display WP (and not mission ended or something similar). From there, if you toggle the mission switch off, it will loiter in place, and if you toggle once more mission switch on, it will go back to WP1 and start over again.

@mac16a Год назад

I like you dude, the loads of effort you put into making this fpv stuff more accessible for people. I think I watched all your videos and it's just everything you can think of. From informative tutorials through relaxing cinematic views to sitting on the edge of my seat when you do low passes at 200 kph. I return to your channel when I need to boost my mood, when I am looking for an inspiration for my next build or just to check if you are still uploading. Sincerely Maciek.

@AdamGdoesFPV Год назад

Thank you for the great feedback, I really appreciate that! 🙌🏻 best comment❤️

@jojo-._. Год назад

you are the greatest! I bet not even flitet test could explain it more harmless and simple than you. Keep it up!

@AdamGdoesFPV 11 месяцев назад

Thank you! I appreciate the feedback 😎

@jakewilliamson7402 4 года назад

So glad you made this! Last flight my aircraft wasn't entering Nav waypoints.I am now very hopeful to have it working next flight!

@AdamGdoesFPV 4 года назад

Glad I could help! Have you realised what was preventing it based on this video? Cheers

@sams9716 4 года назад

Did my first WP mission today, just a small up the valley and back to try it out. This helped out a ton! I do want to add one thing though. Set the nav_wp_safe_distance to 0. If your first waypoint is further than what you have it set to you will not be able to arm the plane.

@AdamGdoesFPV 4 года назад

Hi Sam, great to hear this video was useful and that your first mission was a success! Yes this is correct, unless you increate the value to a high enough number, setting the nav_wp_safe_distance to 0 bypasses this check. Cheers

@VasMikey 3 года назад

Great Job! I will try it once it stops raining over here.

@AdamGdoesFPV 3 года назад

Glad this helped :) enjoy! Cheers

@vasiliyklx450r 3 года назад

Awesome "howto"! 😊👍 All details are covered in a nice, understandabe fashion! With real example at the end 👍

@AdamGdoesFPV 3 года назад

Thanks for the great feedback 🙌🏻😁

@maxun1 2 года назад

Adam we need a update video. This was fantastic.

@AdamGdoesFPV 2 года назад

Maybe some day, I've not used WP missions for a long time and I believe they've changed a lot. Cheers

@kylemagee9999 4 года назад

Thank you very much, spent a few hours now just to get waypoint missions to work. You have to load the mission by using your right stick solved my prob.

@AdamGdoesFPV 4 года назад

Haha yeah that’s why I made this video, to stop people getting confused and frustrated about those little things I had to figure out along the way. I don’t like that you have to load it, on occasions I still forget 🤦🏻‍♂️

@SonAndDadFPV 4 года назад

So much improvement possible in Inav. People like you keep things evolving 👍

@AdamGdoesFPV 4 года назад

Thanks 😊 there seems to be just small things here and there that confuse people... and it’s usually something that could be a real easy fix 🤷🏻‍♂️ it’s getting better all the time and I really like it now

@OwlEyeDroneServices 4 года назад

Hey friend! This is amazing! I love FPV, I'm so happy to be a part of this hobby 😍 I'd love to do autonomous flights as well! Can't wait to see more videos from you!

@AdamGdoesFPV 4 года назад

Thanks for watching and for the feedback 😁

@OwlEyeDroneServices 4 года назад

@@AdamGdoesFPV of course! I'm always happy to see others enjoying the hobby like me 😊

@rcmonster99 4 года назад

Thank you ! clear precise and no waffle....I'll definitly try it !

@StefanNaewe 4 года назад

Excellent! I've never seen an explanation like that.

@AdamGdoesFPV 4 года назад

Thanks :) hopefully it was useful!

@holaperrito2554 4 года назад

Excellent video. Thanks for taking the time to do this. Broke it down to chewable size and I appreciate it. Will be coming back to this video when I’m ready to test way point mission

@AdamGdoesFPV 4 года назад

Glad it was helpful! Good luck with your first mission :D

@imiptat 3 года назад

Great video. I wish more ppl kept it straight to the point

@AdamGdoesFPV 3 года назад

Thanks, I appreciate the feedback 👍🏻

@christopherleveck6835 4 года назад

Very informative and timely as I was going to tackle this very project today.

@AdamGdoesFPV 4 года назад

Thanks, hopefully this will help you get up and running with tour mission nice and quickly 👍🏻

@NOXFPV 2 года назад

Excited about missions. Thanks

@AdamGdoesFPV 2 года назад

Good luck! Thanks for watching :)

@t413com 4 года назад

Nice to have some more content about this out there! Definitely launched without using the stick command and had to land so many times 😆 Can't wait to see more WP things in the OSD.. I really should try being a dev for that project.

@AdamGdoesFPV 4 года назад

Yeah more OSD items would be useful! Glad I’m not the only one forgetting to load before launching! 😂

@philthayer4087 4 года назад

Thanks! I've been struggling with starting a mission with a rover. nav safe distance was the issue. There's actually very little mission control info out there. thx again!

@AdamGdoesFPV 4 года назад

Yeah I noticed there was a lack of info, which made it a little frustrating to learn how it works... thought this video might save others from the same frustration. There is a bug in my AR in relation to the nav safe distance, it doesn't work at all. If i set it to 5 meters It will still activate and successfully complete a mission where the first wp is 700m away. Thanks for watching

@joaoferreira8044 4 года назад

This video is really helpful, I will build my mini talon next weekend with inav

@AdamGdoesFPV 4 года назад

Glad it helped, good luck with the MT, it's a great little plane!

@felixFPVDrone 2 года назад

Excellent tutorial!

@AdamGdoesFPV 2 года назад

Thank you! A bit outdated now but probably still mostly applies. Cheers

@peterpaul100 4 года назад

solid explanation! I will try this mode again and feel confident it will work this time. Have subcribed for more clear vids, looking forward

@AdamGdoesFPV 4 года назад

Thanks for the feedback and sub :D

@peterpaul100 4 года назад

Mode worked flawless! Ready for extended range

@wippo76 2 года назад

This was great help Thanks for making this video

@AdamGdoesFPV 2 года назад

Thanks, glad it was helpful. Enjoy!

@_ShaDynasty 4 года назад

Great explanation

@AdamGdoesFPV 4 года назад

Thanks Jason, hopefully you found it useful 😊👍🏻

@steinne 3 года назад

thank you for the great details-

@AdamGdoesFPV 3 года назад

No problem, hope it was useful :)

@raffman4266 4 года назад

Great vlog adam! Thank you! Kudos to your channel!

@AdamGdoesFPV 4 года назад

Cheers, I appreciate your feedback 😊👍🏻

@markw5066 3 года назад

Brilliant & helpfull video. Thanks

@AdamGdoesFPV 3 года назад

Glad to hear it was useful Mark 👍🏻

@peretzer 4 года назад

Thank you very much Adam

@AdamGdoesFPV 4 года назад

You’re welcome, hope it was useful 😊

@obrujito1 Месяц назад

Greetings, great video. I have a mission scheduled behind the mountains, I will surely lose TX signal, I will use the parameter failsafe_mission_delay = -1 so that the mission continues using the GPS. But what happens if I also lose the GPS? What function would this parameter do in the mission failsafe_gps_fix_estimation_delay = -1 ?. Would it be better to activate the failsafe_gps_fix_estimation_delay = 7 ? Would this activate the FS even if I have the ailsafe_mission_delay = -1 ? Now INAV 7.1.2

@Ard1400 4 года назад

Nice Adam! Great video

@AdamGdoesFPV 4 года назад

Cheers mate :D

@EnglishTurbines 4 года назад

Nice overview, thanks..🤔🤔😳😳😎

@AdamGdoesFPV 4 года назад

No problem 😊👍🏻

@robinvanlooy294 Год назад

Hi nice video, I am planning to build a fixed wing from scratch and want to use the Matek F411 WTE as FC. I was wondering if you would know if this FC is capable of waypoints missions. I assume it is since it runs on Inav 4.1 or higher but I am new to Inav so I am not 100% sure. Greetings Robin

@AdamGdoesFPV Год назад

Hi Robin, I run inav 5.1 on that FC no problem, so I can't see why you wouldn't be able to run WP missions on it. Cheers :)

@WDZaphod 4 года назад

Thanks!

@AdamGdoesFPV 4 года назад

You’re welcome

@serang 3 года назад

That speed setting is used by multicopter. Fixed wing doesn't care about the speed value in mission control 😁

@AdamGdoesFPV 3 года назад

Yea, as per video description you need to set the ‘cruise speed’ as that’s what is used in WP missions.

@nutsidea Год назад

Hi. 2 questions if you could help enlighten. 1) what if mid WP mission I want to abort, how do I take back control of the plane? 2) when it RTH and loitering, how do I take control back and land it? Thanks.

@AdamGdoesFPV Год назад

Answer is the same for both. Just switch to a manual flight mode and you'll be in control.

@nutsidea Год назад

@@AdamGdoesFPV Thanks! Got it!

@philthayer4087 4 года назад

Really good tut!!

@AdamGdoesFPV 4 года назад

Thanks Phil :)

@Videolinquency 4 года назад

Very clear and instructive, thanks a lot! Getting ready to move into iNav from Vectors, but I use slower models than you seem to do, and don't like the idea of specifying a certain ground speed - that spells battery drainage in headwinds and stalls in tailwinds. In models with no pitot tube, I always set the speed to zero; that makes the FC ignore GS and just fly the craft. Does iNav offer the same option, or would it try to hover if you set speed to zero?

@AdamGdoesFPV 4 года назад

Hi, unfortunately iNav still isn't making good use of the airspeed information, i found out recently it's only used for reference on the OSD and is not used by the AP for autonomous flying, maybe this will change in the future, as it's always improving. Someone has mentioned to me that the speed in WP is not actually used at all and that it uses your cruise throttle value instead. This makes sense for it to operate this way but if that's the case I wish they wouldn't put a speed option in to confuse people. It was just coincidence that my cruise throttle makes it fly around the same speed as I had set in my missions. Hope this helps.

@Videolinquency 4 года назад

@@AdamGdoesFPV Certainly! Throttle value is just as good as airspeed, if not better. Ground speed is what I want to avoid. A lot of RCers seem to forget - understandably - that the model's reference point is the air it flies in, not the ground they stand on. The plane doesn't know or care whether it goes up- or downwind. As long as there is a way to make the FC ignore ground speed, I will be able to use iNav.

@egtreadway4232 3 года назад

I've been playing with setting up waypoints in inav 3.0.1 but looks much different, there's not information on this that I can find but the safe home section is now there and no rth box to click, I know you are probably busy but video on this would be nice. Or maybe it can be explained I don't know, the no rth box worries me but Thanks

@AdamGdoesFPV 3 года назад

Hey, interesting to hear, I’ll take a look. Not even opened the WP tab since moving to 3.0

@egtreadway4232 3 года назад

Thanks

@egtreadway4232 3 месяца назад

I know things have changed since this vedio but I'm trying to find out if flying mission inav 6.1.1 and rc link is lost how to continue mission? If there's any documentation I can't find it. Thanks

@divingfalconfpv4602 3 года назад

thinking of trying this for a long flight time test. Drone flew last time 40mins and i want to try and beat that. Gets really boring trying to hold 18mph and go in circles for over 40mins lmao

@AdamGdoesFPV 3 года назад

Ah yeah endurance isn't fun. To make it fun you should take a second plane up and chance the one that's on a mission ;-)

@Urko76 3 года назад

Dear Adam, Thanks a lot for the very instructive video as usual. I have one question regarding to the speed. Can you change it in the different WPs? I friend of mine told me that the plane does not take care of the speed you put in each of the WPs but in the microseconds you have set in navigation system such RTH. Is it true? I hope that the mission can control the ground GPS speed as it looks like in your video. Can you clarify it please? Thanks again, Urko

@AdamGdoesFPV 3 года назад

Hi, unfortunately you cannot control the speed between waypoints. The speed during your entire WP mission is controlled by the 'Cruise_throttle' value. This is the same value that is used by all nav modes like RTH. Cheers

@Urko76 3 года назад

Many thanks for your quick answer. Regards

@jcfpv3454 4 года назад

Thank you so much very helpful

@AdamGdoesFPV 4 года назад

Glad it helped! Thanks for watching

@Chris-vc1dh 4 года назад

how did you do it that your aircraft is so stable in navigation mode? thank you for sharing

@AdamGdoesFPV 4 года назад

Hi Chris. I wish I had a useful answer but I've done nothing. It's actually on the stock tune. Maybe it was just a fairly calm day. Cheers

@kyle3watt 3 года назад

Hi Adam , was wondering how to load the mission using mode 1 radio ? the Throttle and aileron is same stick. thank you.

@AdamGdoesFPV 3 года назад

Should still be elevator and Aileron into high position, whatever that may be on your tx. Worse case is you can load it by connecting to configurator with laptop

@haloaste 4 года назад

Thanks Adam for the great video. I am concern regarding the speed, as I set 2400cm/s, BUT, this works only if you have a pitot probe installed on the plane. If your speed is set to 86kmh, this create problems when i have tailwind or headwind, as my plane is without the pitot probe, it tries to mantain the target speed even on headwind, and this causes full thrust at time. Tailwind causes a plane to stall. I tried an avarage speed which suits both wind components but this is not reliable. Any chance I can get a fixed thrust at all time?

@AdamGdoesFPV 4 года назад

Hey and thanks for the feedback. Unfortunately, I discovered after making this video that the speed you set in WP is no longer used, and your cruise throttle is used the entire time you are in a WP mission. Try increasing your cruise throttle for a WP mission and see if this helps. In iNav from what I understand a pitot air speed is only used to show an ODS reading for your reference and is not yet used in any of the automated flight by the AP. Hope this helps.

@53roger 4 года назад

Good video and useful information Adam, Thank you. I have WP set up on my fixed wing and a 6" Quad. One question about Inav Missions on a quad. When the quad arrives at a way point it almost stops, turns toward and then continues to the next WP. Does anyone know how to program INAV to 'fly through’ the way point much like a fixed wing does without stopping. I guess you could call it a 'smooth transition' at the WP.

@AdamGdoesFPV 4 года назад

Thanks 😊 not sure on the quad question, never had a quad on iNav. Maybe setting the distance from wp to consider it reached would help?

@53roger 3 года назад

@@AdamGdoesFPV Just for anyone curious...I made the 'WP reached distance' much larger but the quad still abruptly stops at the way point, turns, and then continues toward the next WP. A bit annoying but at least it will complete a mission.

@AdamGdoesFPV 3 года назад

@@53roger seems like strange behaviour. The wp functionality is very simple in iNav maybe on a quad you’d be better off with something like Ardu

@kawasakizx14jomamamoto57 3 года назад

That was hilarious, if you really want to go get your plane out of a tree, check this box.

@AdamGdoesFPV 3 года назад

😆 so true though haha

@mangjanachannel 2 года назад

Hey adam, the altitude is from sea level or from land that you launch the plane?? Thank you...

@AdamGdoesFPV 2 года назад

Hey, it’s altitude from launch point. Also if you’re using iNav 3 or 4 I believe WP has changed quite a lot since this video.

@sonyhadi8866 3 года назад

hello Adam, how if lost connection between remote and air plane, Waypoint still continue or fail safe?

@AdamGdoesFPV 3 года назад

If 'failsafe_mission = OFF' the failsafe procedure won't be triggered and the mission will continue if you lose RC link during a waypoint mission

@sonyhadi8866 3 года назад

@@AdamGdoesFPV thanks for your answer very helpful

@MrVasmikey 4 года назад

Fantastic! Thx so much.

@AdamGdoesFPV 4 года назад

You're very welcome!

@MrVasmikey 4 года назад

Adam G does FPV this information rocks! I have been combing github but haven’t been able to put it all together. Here you have done it and answered all my questions. Bless you!

@kajbyman3006 3 года назад

What if you loose the RC signal during the flight,and when the plane complete it's route,how do you establish the signal again to land?

@AdamGdoesFPV 3 года назад

99% of control link failsafes are down to going out of range. If this is the case then you’d simply regain your link when the plane gets closer to home. This is assuming you either set the last wp near home or you chose the option for it to RTH at the end. Hope this helps

@trumblez Год назад

Is it possible to make the plane loop the mission so it just keeps repeating the mission?

@AdamGdoesFPV Год назад

I've not tried WP missions for a long time now... but I believe this is now possible in the later versions of iNav.

@trumblez Год назад

@@AdamGdoesFPV ok, I think i found out how to loop a Mission a defined number of times, but how to loop them indefinetly.

@nutsidea Год назад

Hi Adam. I have another question regarding regaining RC link. Will the waypoint mission continue when RC link is back on? meaning if between waypoint 23-30 I lost RC link due to distance, when it flies back in the range and RC link is reestablished, will it continue with waypoint 31, 32 .... ? And I can also choose to turn off waypoint and take control of the flight there on? Thanks.

@AdamGdoesFPV Год назад

Yes to both 👍🏻

@nutsidea Год назад

@@AdamGdoesFPV Thanks lots for your reply. I have successfully executed Waypoint Mission based on what you had shared.

@juanvivo147 Год назад

Is it possible to have the option that when the last waypoint ends, the mission starts again from the first waypoint?

@AdamGdoesFPV Год назад

In the latest version this might be possible. Back when I made this video it was not possible

@raffman4266 4 года назад

Adam what is your All up Weight with your Ar Wing Setup? I have the same setup and found it hard to takeoff when there is not much wind. So i changed my motor to 1400kv and a 8x6 prop at 3s 2200mah. My AUW is 804grams

@AdamGdoesFPV 4 года назад

883g with the heavier setup using the Osmo action camera.What weight was yours that it was struggling to launch? or are you still having a hard time at 804g?

@raffman4266 4 года назад

Adam G does FPV Struggled at 804g with a 3s 3200mah 2200kv x 6x4prop so i changed my power setup to a 3s 2200mah 1400kv 8x6prop. Its flying with much confidence and authority now. Have to check Amp draw though if it will be almost the same with the former setup.. You’re really doing a great job with your vlogs! Making the hobby more exciting and more easy to understand! Kudos to you Adam!

@Chupria 3 года назад

What is the maximum length of the mission? For example, can I send a gift to my grandma who lives 300 miles away using waypoints? Given that the batteries will last that long.

@AdamGdoesFPV 3 года назад

From memory there is no max distance but a max number of waypoints. So yes you can drop grandma her gift 1000 miles away if your battery will last 👍🏻

@Chupria 3 года назад

@@AdamGdoesFPV Thank you. I like that you answer every question as you stated in the video. This is totally new concept for me. 👍🏻

@dekiaza 3 года назад

Hi.. how to setup on inav if we want the plane fly at certain speed, example if the plane will fly with ground speed / air speed at 45 m/h constantly. thank you for your help

@AdamGdoesFPV 3 года назад

Unfortunately this is not possible. When entering WP mission the plane will use your 'Cruise Throttle' value. You can of course adjust this to get it to fly as close to the speed you like, but then it will be affected by wind. Hope this helps

@dekiaza 3 года назад

@@AdamGdoesFPV hio thank you for your reply, where i can setup the cruise thr value? thank you

@AdamGdoesFPV 3 года назад

@@dekiaza From memory I think its in the Advanced settings tab, on the right hand side half way down. This value is used by all automated flight modes so it's important to get it right

@dekiaza 3 года назад

@@AdamGdoesFPV ohh.. okay, many thanks for your replay.. :-)

@myvideointube Год назад

good

@AdamGdoesFPV 11 месяцев назад

Thanks

@egtreadway4232 3 года назад

I've been playing with inav mission planner and my c1 chaser with f405-wing and inav 2.5.0 I really like doing missions, I'm trying to figure out how I could monitor the flight in real time on a android device, how could I do this ?maybe bluetooth module to radio video you did ? Maybe a gps tracker? Any advise would be appreciated Thanks

@AdamGdoesFPV 3 года назад

Not sure to be honest, iNav isn’t currently designed for live tracking. I believe Ardu Plane is great for this if that’s what you want to do.

@egtreadway4232 3 года назад

Ok thanks, do you use the inav mission planner app? Just wondering would this give ability to monitor flight in real time? Thanks

@siogana 2 года назад

How about using switch.. And activating after flying in the air

@AdamGdoesFPV 2 года назад

Thats exactly how I did it

@siogana 2 года назад

@@AdamGdoesFPV switch didnt load wp from eeprom?

@小坂裕-c5u 3 года назад

Hi,Adam. If I raise the right stick diagonally upwards before arming, load the WP into the FC, then launch the plane with Autolaunch, will it seamlessly transition to the WP mission after Autolaunch?

@AdamGdoesFPV 3 года назад

No you have to activate the waypoint mission, it is a flight mode.

@小坂裕-c5u 3 года назад

@@AdamGdoesFPV Thank you. I was misunderstanding.

@Koestel-FPV Год назад

If you lose the RC link (failsafe) is it possible to continue the mission in automatic? Thanks

@AdamGdoesFPV Год назад

Yea, I’m pretty sure it’s part of this tutorial from memory. There is a CLI command for it

@Mateyhv1 4 года назад

If you dont select RTH a fixed wing will loiter around the last point, I asume a multirotor will enter POSHOLD.

@AdamGdoesFPV 4 года назад

This makes perfect sense and is what I expected, but didn't want to just assume. You never know with iNav! Thanks for the info :D

@turboromy Год назад

Just wanted to share, at 8:05 CLI command changed to get nav_wp_max_safe_distance in later version inav. failsafe_mission at 9:22 doesn't work either in 6.0 and look like failsafe_mission_delay = -1 makes the failsafe procedure won't activate at all.

@AdamGdoesFPV 11 месяцев назад

To be honest I might take this video down as WP missions have changed so much in iNav this is no longer relevant. Thanks for the info

@turboromy 11 месяцев назад

@@AdamGdoesFPV I was unawake when I saw this and wondered how anyone could find my upload and want to take it down. Your waypoint video was one of a few I watched before trying it. It did smaller area waypoint with no issue, but on 2nd trial covering a bit larger area (but nothing crazy at all), it failed. Quite weird way. Have you experienced or heard anything like this. R-XSR is a suspect and will retry with a fresh part. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-5BHoS3-ULBM.html

@samiroraut 3 года назад

Hi Adam, On clicking mission control on my inav, i cannot see the map screen that is seen in your video. What needs to be done ?

@AdamGdoesFPV 3 года назад

Sorry I’m not sure, never came across this issue 😬 check out Rag the nuts off channel. He did a video on how to change the source of the map iNav uses. This might fix your issue

@upnorthFPVandEUC 7 месяцев назад

is there a stick command to stop the mission? or do i just flip the nap wp mode to off?

@AdamGdoesFPV 6 месяцев назад

Yeah just turn off WP mode

@dmhans22 4 года назад

What is the advantage of inav than ardu?

@AdamGdoesFPV 4 года назад

Hard for me to say as I've never used Ardu. For me I found iNav easy enough to learn and use, but I hear Ardu is not as user friendly. Many will tell you it works better than iNav if you can get your head round it though. I just don't have the time or desire to learn another right now

@TheJuli8898 3 года назад

Is it possible to connect a pi via mavlink to a FC running INav for the purpose of utilizing a 4G Stick to stream live Data from a flight? I've seen pixhawk and ardupilot having Mission control centers that allow live tracking. Can inav do that aswell? I really don't want to go back to ardupilot but I really need a live update of where my plane is for long range flights.

@AdamGdoesFPV 3 года назад

Hi, unfortunately iNav isn't very good in this regard, something like Ardu is much better for live tracking and making live adjustments. Thanks for watching

@peterhancox5268 5 месяцев назад

OK. Now some time later and INAV version 7.1. Do you know how to delete a saved mission(s) that has been saved to the EPROM. I.e remove from the EPROM. Thanks

@AdamGdoesFPV 5 месяцев назад

Sorry not used WP missions for years so I’m not familiar with the changes in recent FW

@BBFPV 4 года назад

strings set nav_wp_radius = set nav_wp_safe_distance = 0

@AdamGdoesFPV 4 года назад

Thanks I've added all CLI I discussed in this video in the vid description: CLI mentioned in this video: -nav_wp_safe_distance = First waypoint in the mission should be closer than this value [cm]. 10,000 (100m) default. Set to 0 to bypass this check. -nav_wp_radius = Waypoint would be considered reached if plane is within this radius. Default 100 = 1m -failsafe_mission = If set to OFF the failsafe procedure won't be triggered and the mission will continue if the FC is in WP (automatic mission) mode

@tonyyeung821 4 года назад

I also forget to load missions before taking off. My trick to remembering is that I've changed my "armed.wav" voice notification to actually say "Armed. Did you remember to load waypoints?". You don't want waypoints to automatically load. If you are at a different field, automatically loading waypoints will prevent you from arming because the 1st point is too far away, even if you don't enable WP mode.

@AdamGdoesFPV 4 года назад

Haha I had considered doing the same as you, it's a smart move if you do WP missions often! I would still like it auto load, because then when you fly, if the WP is at a different field, the nav_wp_safe_distance will stop it from starting the mission, so there shouldn't be an issue. Thanks for watching

@tonyyeung821 4 года назад

Unfortunately, the nav_wp_safe_distance check works by preventing you from arming. Try it. Set the safe distance to 1m. A better way to implement the check would be to prevent you from putting it into WP mode.

@AdamGdoesFPV 4 года назад

Right I've just been and tested this. I have a WP mission loaded and I am able to arm successfully in my back garden while my first WP is about 8km away.

@tonyyeung821 4 года назад

Hmm. When I first setup a mission, my first waypoint was further than 100m away. I loaded the mission from EEPROM and it wouldn't let me arm. I see a message in the OSD "Unable to ARM. First waypoint is too far". (Just retested). I had to connect a computer to my plane and change the safe distance. Looking at iNav issues, I see this as an open issue: github.com/iNavFlight/inav/issues/4832. Perhaps you are running a version of iNav that behaves differently. (I'm running 2.4). Or perhaps you didn't actually load waypoints from EEPROM before you armed?

@AdamGdoesFPV 4 года назад

@@tonyyeung821 I honestly believed you were going to be right, but I have just tested it in my back garden, loaded the mission in the usual way (Stick up right before arming) and then I can arm no problem. My safe distance is set to 500m and first wp is approx 8km away. I am also using 2.4. I tired this 3 times just to make sure and cycled the power each time. On the third time I even connected to my computer so I could confirm the mission was loaded in mission control.

@dekiaza Год назад

Is matek F411 wing can setup mission on inav?

@AdamGdoesFPV Год назад

I can't see why not

@k1ortia 3 года назад

just went to try mission planner today for first time, and all im getting is a blue screen. no maps or anything. The plane and gps though is all working perfectly. Any ideas whats wrong or what im not doing? cheers

@AdamGdoesFPV 3 года назад

Are you using a chrome app or standalone configurator?

@k1ortia 3 года назад

@@AdamGdoesFPV Hi Adam. i think iv got it now. Had a quick look at a video painless 360 did. He said on the blue screen you have to zoom all the way out, then you see the world map. Then zoom back in to your area. Its Kind of weird why you have to do that and your location is not displayed as soon as you go into missions. But i get it now. its so you can plan which ever autonomous flight you want in which ever location you choose and differs from the gps tab, which does show your real time location. I think any way. i could be wrong.

@philthayer4087 4 года назад

Is a compass required for fixed wing? When I try and start a mission it says. Nav not safe. Yet I have 14 sats and RTH works perfectly. Any ideas?

@AdamGdoesFPV 4 года назад

Fixed wing do not need a compass. In fact using a compass can cause problems so you should disable it. Not sure why you're getting that error. Make sure you haven't set number of sats required too high

@53roger 4 года назад

here is a video that will show you how to solve your problem (i had exactly the same issue a couple of days ago) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7MAdgGkBkXs.html There is also addition information on Inav Wiki that can further explain the Navigation is Safe pre-check here github.com/iNavFlight/inav/wiki/%22Something%22-is-disabled----Reasons#navigation-unsafe-reasons roger

@PEDVED88 3 года назад

Is the stick command the same in mode 1?

@AdamGdoesFPV 3 года назад

No you'd need to move the left stick to the top right. iNav is looking at the roll and pitch signals being at 2000, so that would be your left stick.

@PEDVED88 3 года назад

@@AdamGdoesFPV If I have to throttle at 1000 (down), rudder at 1500 (center), elevator at 2000 (up), roll 2000 (up) I get right hand down left and left hand up and center (in mode 1)

@AdamGdoesFPV 3 года назад

@@PEDVED88 Ok I just looked at Mode 1 layout and it's different to how I thought. But the way I see it now is left stick top middle, right stick bottom right.

@kornface13 4 года назад

Has "speed" changed in 2.4? In the past, speed has no function. INAV doesn't consider plane speed (GPS or pitot), it only uses throttle values

@AdamGdoesFPV 4 года назад

This could still be the case to be honest! I never really altered the speed for wp missions and it might just be a coincidence that my average cruise speed ends up being around the same as the speed I set. Thanks for pointing that out 👌🏻

@AndrewNewton 4 года назад

@@AdamGdoesFPV Great video Adam. Yes I found out about speed just yesterday on my first mission in the air. It flew at the Cruise Speed not my entered waypoint speed.

@AdamGdoesFPV 4 года назад

@@AndrewNewton Thanks for confirming this Andrew. This is so weird because it states in the wiki that "The mission is defined with waypoints, which have the information about latitude, longitude, height and speed between the waypoints"... and of course it allows you to set the speed which adds to the confusion

@jibbajabba4597 4 года назад

Adam G does FPV that only applies to drones iirc. Pawel said something about they couldn't get reliable speed on planes so it flies at cruise setting, unfortunately adding a pitol tube doesn't help either which can make things interesting on windy days. More annoyingly jump and loiter don't seem to work, it seems the inav team are concentrating on quads.

@AdamGdoesFPV 4 года назад

@Dominic Douglas Nice little tip, I can see that being very useful for people flying a lot of WP missions!

@Chris-vc1dh 4 года назад

how do i load mission with radio in mode 1?

@AdamGdoesFPV 4 года назад

Should just be left stick (elevator/aileron stick) held in the top right corner for a few seconds.

@Chris-vc1dh 4 года назад

Adam G does FPV I will test it, thank you for your help.