Install an Axle Truss - TMR Customs

Подписаться 563 тыс.

Просмотров 88 тыс.

50% 1

Get 5% off your order at TMRCustoms by using the coupon code found here: bleepinjeep.com/discounts/
In this video I'll show you how to put together, install, and weld on an axle truss from TMR Customs onto my Rubicon Dana 44 axle that will be going into the Scorpion Crawler Project. The Truss is pretty sweet and will help beef this sucker up for some extra rock crushing fun!
tmrcustoms.com/
Website: www.bleepinjeep.com
FaceBook: / bleepinjeep
This product is meant for entertainment purposes only. Your mileage may vary. Do not try this at home. Void where prohibited. Some assembly required. For off-road use only. Slippery when wet. Batteries not included. Do not use while operating a motor vehicle, heavy equipment, cherokee XJ, wrangler TJ, wrangler JK, or any Jeep vehicle, especially the newer Fiat ones. How-to videos may be too intense for some viewers and children under 30 years of age. Please remain seated until the 4x4 ride has come to a complete stop. Studies have shown viewing these videos causes increased cancer risks in laboratory test people. I am not a professional, I have no training, I'm not even particularly good at horse whispering. Don't believe everything that you know. Please keep your hands in the vehicle at all times. Do not tap on glass. Do not eat anything that has been on the floor for more than 3 days. Keep your hands to yourself. Not to be taken internally. Reproduction strictly prohibited. Driver does not carry cash. Objects in Bleepinjeep mirrors may be farther than they appear.

Авто/Мото

Опубликовано:

11 май 2015

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 98

@codymoncrief2128 7 лет назад

The heating is almost entirely to keep the cast housing from cracking due to stresses cause by sudden and uneven heating. Likewise the blanket helps it cool down more evenly and gently, as quick cooling can cause cracks also.

@kevinstevens9834 9 лет назад

Awesome job installing that truss. I have a TMR truss on my 2008 JKU, couldn't be happier with it. TMR puts out some fantastic gear. Just ordered their 2.5 ton steering kit. We are happy to have them here in Ontario (Canada). TMR has a booth in the Unlimited Off Road show in Kentucky next week. Check them out.

@bobhunt3197 5 лет назад

The reason for pre and post heat is to ensure the molecular enhancement of the two dissimilar metals, thus encouraging them to become one with each other, and live happily ever after, the end.

@syzfilms 9 лет назад

Good stuff again Matt. I don't do my own work anymore but I really enjoy watching your get it done.

@ShannonLacey78 5 лет назад

Is it me or does this guy look like Hans Gruber and sound like Mr. Rogers?

@junksilver4144 9 лет назад

One of your best videos dude.

@RobPipo 7 лет назад

what an excellent video. im gonna do the same to my 44 on my jk. this really helped

@ADHomesteading 9 лет назад

Looks like you did a good job. Thank you for the video.

@larryalexander4833 6 лет назад

not sure if the best way but when I have wielded on cast ( farm equipment or tractor parts ) I used a rag soaked in antifreeze to keep heat down and in one area. Also older cast I believe was lote more dense not as porous

@gonzala 9 лет назад

The reason for preheating the cast iron is because a rapid heat up and cool down in a small area could cause it to crack or become very brittle and likely to crack. its better to preheat the entire piece if you can rather than just the areas you are going to weld. if not, an alternative to preheating would be to weld in small increments and covering it while it cools (till you can touch it) between welds.

@jeremysmith8990 5 лет назад

gonzala you are dumber than hell, you don’t have to heat the whole piece, only the area immediately around the weld area (2-3”) and let the heat soak into the areas around it!

@brianfedie8046 4 года назад

Just what I need!

@gilliland426 9 лет назад

great job matt!

@stephenkemp2546 7 лет назад

Awesome! I was wanting to do this and now I'm going to after watching this video. Quick question tho. Is there a kit for the rear as well?? I can't find one if so. Thank!!

@LZDEN 9 лет назад

very good work Matt.you did a great job there...;-)

@Mattie_Ice 5 лет назад

Would it help to keep the axle shafts inside to prevent heat warp?

@liftonly2 9 лет назад

You should fill in your craters when you finish a weld. It'll be Stronger and it looks nicer

@AndrewBrowner 6 лет назад

what about the inner Cs that hold your ball joints and such, arent they the weak point for bending? would it be better to use a kit or make youe own truss setup that spans from the C to the pumpkin? or even C-C and than pumpkin welding is optional although id still weld to the pumpkin to tie it in better to the tubes

@davidthorne3460 5 лет назад

would you recommend Mig over stick for trusses?

@stateservant 5 лет назад

how many percent will the strength be increased? i am going to mount far larger engine wighing approx. 2 times, please advise..

@OffroadMilitia 3 года назад

Bout to make my 14 bolt trusses. Thank you

@arthurbothamjr8104 9 лет назад

Thanks for making another great video! Was wondering how you set the caster angle? Looks like you eyeballed it, I'm guessing you can adjust with the y-arms, no?

@bleepinjeep 9 лет назад

Arthur Botham, Jr ya I didnt worry about that and there isnt much adjustment there but the adjustable arms will make up any difference

@curtis4991 8 лет назад

Sometimes, I shield my eyes when watching welding on RU-vid.

@Bronkey469 7 лет назад

Chad Freznerdickson Why?

@IDK9000100 6 лет назад

It’s good practice lol

@anderspanders9698 3 года назад

What MIG wire (size and grade) are you using to weld to the ductile? 70S-6?

@lsa_transamws6943 7 лет назад

Did you change wire when you were welding to the cast steel housing? I need to weld some steel mounts on a Ford 8.8 housing and have heard mixed things about the welding technique.

@stevebibey9816 7 лет назад

Eric Wallin

@Rogue.Rider0 4 года назад

Wish I could find a good truss for TJ dana 35.

@drmaddwheels3686 5 лет назад

Did you replace the seals.. they might not have made it through that much heat

@UnitCrane514 9 лет назад

That looks really cool! Doesnt that cause the axle it warp upwards when you weld on it? Those shaft housings are just extra heavy pipe thats been trued up by being line bored. If it pulls up just a .0001" it can cause tons of wear on your bearings and what not.

@nitroevaderbx 9 лет назад

UnitCrane514 he mentioned several times that he took his time between welds to prevent it from warping. also there is no way that .0001" will do anything.

@bradleycampbell5933 9 лет назад

Jacob Lauritzen the only way i can see chance of warping is to run 24 inches of weld at once. the rest of that was song and dance for no real reason. speed kills, get your task done and over with.

@KyleDodder 8 лет назад

Awesome vid! Is there anyway I can truss my axle without gutting it out? It's been newly rebuilt with an ARB and what not and there's no way I can see myself redoing it?!??

@bleepinjeep 8 лет назад

+Kyle Dodder hmmm, I would so you probably can... just dont get it too hot or melt the seals.

@KyleDodder 8 лет назад

+BleepinJeep cool thanks for the quick reply!!!

@AndrewBrowner 6 лет назад

whats too hot? is the 400F pre heat going to be too hot? would it better the leave the oil in while heating to help even out heat internally or drain the diff oil to prevent it from transferring heat from the pumpkin to the gears and seals as much

@ltaldorein4764 9 лет назад

Are you going to be doing an anti wrap bar on this build?

@bleepinjeep 9 лет назад

Ltaldorein If I stick with the leafs then yes for sure.

@jtwelding4387 9 лет назад

you preheat cast iron because its high carbon, if it heats up fast and cools off fast it will crack

@UnitCrane514 9 лет назад

A lot of guys put welded cast iron in hot sand to cool it slowly and evenly. I thought you were also suppose to pean out cast iron welds to pack it into the pores of the metal and strengthen it????

@Jdmlsturbo 5 лет назад

How thick is the truss?

@binkleahy 5 лет назад

Matt, I hope this isn't a silly question. I was wondering if it is possible to convert a Dana 30 to a Dana 44 front axle? Or would it just be cheaper to buy a front 44? Mind you I have a 2015 Willy's JK with ARB lockers front and rear. Is there any information you can share with me?

@bleepinjeep 5 лет назад

You can do 44 outers but that doesn't change the size of the ring gear...so no. Beef it up and rick it or pony up and spend some dough!

@binkleahy 5 лет назад

Thanks for the response. I might go the route you suggested. With the axle trusts and possibly some bigger knuckles.

@tomd1939 8 лет назад

I saw the carrier was removed along with the pinion. did you also remove the seals to before you heated the pumpkin up? or could the seals withstand the heat?

@itiosso 8 лет назад

Trying to figure this out myself, did you find an answer?

@tomd1939 8 лет назад

+Scotty T. no, never did. I would assume to play it safe and remove/replace them (especially since he's gone this far and the seals are relatively inexpensive in comparison) but I'm not sure

@AndrewBrowner 6 лет назад

did you truss your dana 44 or find an answer on the seals?

@AndrewBrowner 6 лет назад

likewise^

@MrMrsregor 6 лет назад

the seals will be toast after all of this heating and welding. plan to replace all seals and might as well do bearings too while you are in there.

@benjaminvolesky1653 8 лет назад

ah...here's that axle truss vid:)

@boomstickkid 9 лет назад

the dana 44 front you have does not have a cast iron centersection. that is cast steel, much easier to weld then cast iron, you really didnt have to go through all the heating and wrapping with a blanket since it is just cast steel (but heating a bit is still good if youre going to mig cast steel) trust me if that was cast iron and you welded it up with regular mig wire and 75/25 it would of cracked.

@MrMrsregor 7 лет назад

is it a bad idea to use an arc welder with 7018 for welding axle tubes to the ford 8.8 diff housing ?

@jeremysmith8990 5 лет назад

MrMrsregor no but 6010 might be a better choice for the root pass and even it out with some 7018 over top!

@weisser30 5 лет назад

So will that kit mount a Dana 44 to a stock wrangler to suspension

@bleepinjeep 5 лет назад

Yep

@weisser30 5 лет назад

@@bleepinjeep i ment will it mount to a stock tj suspension but my phone auto corrected it sorry

@gibson5056 5 лет назад

WHAT DOES THIS KIT COST?

@joshgrier3014 6 месяцев назад

What wire did you use for it? Maybe missed it in the video

@losoj30 9 лет назад

Was that a Dana 44?

@SuperMopbucket 9 лет назад

So, I'm trying to find the application form to become your best friend. Because I know there would be some definite benefits to having you're skills around. I offer pretty decent skills as well, some include making food, supplying drinks...

@kronik2020 5 лет назад

If that is form an 07 or newer it cast steel and not cast iron and much less prep and preheating need be done.

@nickhylman8319 9 лет назад

At 2:38 it looks like you layed the grinder disc on the cord you should check to see if you accidentally cut the cord if you accidentally cut the cord it could shock you or kill you or catch you on fire.

@walts440 9 лет назад

Nick Hylman looks like he set the grip on the cord

@bleepinjeep 9 лет назад

Nick Hylman I always set them upside down

@oldkingcole4300 9 лет назад

im sure plenty of people have asked this before, but what welder are you using?

@bleepinjeep 9 лет назад

Cole Warwick Its a millermatic 185

@oldkingcole4300 9 лет назад

thanks!

@wildnfreeoverland 6 лет назад

Should of used a Artec Industries truss.

@dre04mach 6 лет назад

That's the one I was hoping to see as well/what I'm planning on using if I ever get around to going 1 tons on my xj

@Akbaker96 9 лет назад

What do you do for a living? Are you a welder?

@bleepinjeep 9 лет назад

Andrew Baker I have a youtube channel called BleepinJeep, its a full-time gig.

@MrMrsregor 6 лет назад

does TMR customs not honor the %5 bleepinjeep discount anymore ? i am ready to buy one of these suckers but cant get the code to work.!.

@bleepinjeep 6 лет назад

hmmm, it's been a while, I will get ahold of them and ask!

@MrMrsregor 6 лет назад

thank you ! their website shopping cart just said "Coupon code "BLEEPINJEEP" is not valid." i am making frame stiffeners and installing long arms now. i plan to do the front axle while it is out of the jeep

@MrMrsregor 5 лет назад

no luck i guess... i was ready to order, but i can find other options :( thanks for posting discounts. i just wish the companies you take the time to advertise for would uphold their end of the bargain

@lanckie 4 года назад

@@MrMrsregor i found that if they are running another discount it will invalidate other coupons

@MrMrsregor 4 года назад

@@lanckie thanks for the tip. they were not running any other discounts when i was building my axle. i ended up finding a good deal on artec truss kit with jonny joints.

@pra3t0rian 9 лет назад

Who was on the phone?

@bleepinjeep 9 лет назад

pra3t0rian hopefully someone important!

@badgett83 9 лет назад

great video! when are you gong to give me welding lessons :-D

@bleepinjeep 9 лет назад

skull squadron bring some steel and a case of Dr. Pepper;)

@badgett83 9 лет назад

Is that diet? Or regular? Haha

@RandomsFandom 4 года назад

do not let it cool down... in fact, i would heat the whole piece to at least 400

@patpollifrone1651 5 лет назад

Hey Matt, what year and model axle is this? Sorry if I missed you saying it.

@bleepinjeep 5 лет назад

TJ Rubi so 03-06

@benniejeeper 7 лет назад

it's cast steel not iron

@jesseyjulson1967 2 года назад

Probably wont reply as the vid is 6 years old. But why didn’t you weld around the tubes at the pumpkin?

@cookiestinky8924 6 лет назад

Could I do this installation without taking the ring, pinion and lockers out? I'm to lazy

@joshyg96 6 лет назад

doubt your axle seals would survive.

@RandomsFandom 4 года назад

that second pieces seems unnecessary

@Adrivingpassion 9 лет назад

BEEF CAKE!!!!

@jeromygreiner2465 4 года назад

Waste of time and money. The dana 30s weak point is the tiny ring gear. Beef up the housing all you want, and add chromoly shafts, and a locker. Then you will tear the teeth off of your ring gear because the contact area is too small. Pickup a dana 60 for less than $300 and install it instead.