Install Baja Designs LP4 LED Lights to Uptop Overland Alpha Roof Rack Installation Instructions

Подписаться 2,2 тыс.

Просмотров 10 тыс.

50% 1

Installing 7 of the Baja Designs LP4 off-road lights on our 3rd Gen Tacoma's Uptop Overland Alpha Roof Rack. Learn tips and tricks as well as from my mistakes here. Sorry we lost battery and much of the electrical wiring footage was lost. I will try to have the testing footage up soon so you can see the light spread of the LP4s across a very large field in pitch black conditions. I can say after almost 6 months I have not had any issues with using my LP4s in hot, cold or wet conditions and none of the hardware has yet to come loose. If you find my content helpful in any way please support the channel with a subscribe as we are very small so our content is not promoted by RU-vid.
Testing the LP4 light bar… wow
Night Test Baja Designs LP4 Off Road LED Lights Overhead on Roof Rack
• Night Test Baja Design...
Thanks!
Keywords: trd, toyota racing development, baja designs, LP4, LP6, LP9, diode dynamics, KC, Harbor Freight, Rigid, ARB, off-road, install, DIY, simple, easy, instructions, Uptop Overland, Roof Rack, Mounting, टाँड, سقف الرف, ਛੱਤ ਰੈਕ, rak atap, rack de teto, багажник на крыше, ルーフラック, Barra de techo, Dachträger, چھت کا شکنجہ, giá nóc, tetőcsomagtartó, portbagaj, rack sa bubong, galerie de toit, 루프 랙, portapacchi, ছাদের আলনা, takstativ, takräcke, rak bumbung, மேற்கூரை வரிசை, tagbøjler, dakrak, дээврийн тавиур, दीपक, أضواء, ਲਾਈਟਾਂ, lampu, luzes, огни, ライト, luces, Lichter, لائٹس, đèn, Lámpák, ışıklar, mga ilaw, lumières, 등, luci, আলো, lys, lampor, lampu, விளக்குகள், lys, ligte, гэрэл, सड़क से हटकर, خارج المسار, ya sgbo, off-road, fora da estrada, внедорожный, 未舗装道路, fuera del camino, Offroad, آف روڈ, ngoài đường, terep, arazi, off-road, hors route, 오프로드, fuori strada, অফ-রোড, off-road, av vägen, luar jalan, சாலைக்கு வெளியே, off-road, veldry, бартаат зам, इंस्टॉल, التثبت, ਇੰਸਟਾਲ ਕਰੋ, Install, instalar, установить, インストール, Instalar en pc, Installieren, انسٹال کریں, Tải về, telepítés, Yüklemek, i-install, installer, 설치하다, installare, ইনস্টল, installere, Installera, pasang, நிறுவு, installere, installeer, суулгах

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 33

@Baseballpro1319 4 месяца назад

How much amps in total does it take? Is it possible if I run the wires to a Blaze Off-Road Garmin PowerSwitch??

@AdventureSquadOverland 4 месяца назад

Not sure about the power switch, give them a call. Each LP4 will draw 5.5 amps. What u building?

@RolexDSSD Год назад

Nice

@AdventureSquadOverland Год назад

Thanks

@jonnytacooutdoors Год назад

Those lights are so bright

@AdventureSquadOverland Год назад

Yes, pretty hard on a cold battery tho, thinking of a dual battery setup

@caseycrick7627 10 месяцев назад

Can you tell me who you had cut your windscreen? Looking to install 8 LP4’s on a TrailRax Bronco as well as 6 LP4’s on the bumper and 1 LP4 on each A Pillar?

@AdventureSquadOverland 10 месяцев назад

Uptop overland. They also made the rack.

@Ed-sh8jt 11 месяцев назад

Does Alfa roof rack manufacturer not sell or make the windscreen cut-out for the LP4 lights?

@AdventureSquadOverland 11 месяцев назад

Yes I purchased the windscreen with LP4 cutouts from uptop overland, same manufacturer

@Ed-sh8jt 10 месяцев назад

Thanks they look great! also on the 14:04 video shot of cable harness connected to back of light fixture. You could have added some black heat shrink help protect the wires and adds a little better look

@AdventureSquadOverland 9 месяцев назад

Thanks. I got lazy tho lol. I’m actually changing the entire setup hopefully by winter 2024 💪🏼

@jodywatkins1037 Год назад

Do you have a picture of the wire harness and how you made it. I'm getting ready to install the same setup. Was told by Baja that I could use 12 gauge to run 4 lights but I was thinking it should be 10 also.

@AdventureSquadOverland Год назад

Yes google amps per ga and u will see we are correct. Don’t risk ruining your gear. I don’t have a pic but what I did was run a wire the length of the LP4s all the way to my switch pro with an extra foot of wire. Then measure the distance between each LP4 and mark it on your 10 ga wire. From there I connected all 3 ends together, or u can connect 2 ends together and then connect that wire to another end (3 ends total). Just make sure there is plenty of surface area contact and make it water tight. Hope this helps, good luck, wish I was there to help 💪🏼

@VWdjs Год назад

What did you use to hide the wires? I go the KC hider but can’t fit all of the wires.

@AdventureSquadOverland Год назад

I just found the wiring video clips…. Ah maybe I’ll upload that video separately when I can get to it.

@AdventureSquadOverland Год назад

@@VWdjs I have a video on this coming in a couple weeks or sooner. Some kind of 3M wire hider I forget the name. Outdoor use tho.

@aidanseanzabs3563 Год назад

@@AdventureSquadOverland did you get a chance to upload that wiring vid clips? about to do same set up. thx.

@kceatc5305 Год назад

where did you get that bracket that joins the two load bars together?

@AdventureSquadOverland Год назад

Uptop overland. If you order the LP4 windscreen they add it I believe and make sure you have everything you need.

@Desmo_racer Год назад

Cool windscreen and light. Where did you get the bracket for the bar?

@AdventureSquadOverland Год назад

Thanks man. I love it still. The bracket came from uptop overland. When u order a specific windscreen cutout they will also include mounts. For this cutout they included the brackets. Thanks for watching and supporting bro. See u out there

@Desmo_racer Год назад

@@AdventureSquadOverland thank you so much. I have different rack but trying to figure out install uptop windscreen with lights.

@AdventureSquadOverland Год назад

Check dimensions, uptop is wider than most other racks. If creating your own, front runner setup might be easier check it out