Installing a 4" Lift Kit on My New Wrangler🔥 *HUGE* 

I'm proud of you man! I'm so glad you didn't " Peter out" with a smaller lift, you actually installed a very substantial, big boys lift!!! And did a really good job I might add 💪 I will definitely be tuning in for future upgrades, now you need some bigger tires, those look like puny car tires with the new lift!

Hey Robbie, one thing I didn't notice in your video. You gotta tighten the suspension when it's sitting on the ground. There might be some tension on the joints. Then it has a hard time settling. Could be a reason the Jeep sat so high right off the bat. Just food for thought. Great videos all around keep it up. You're always new at something until you get into it and get your hands dirty. I'm glad you started with good components off the bat instead of Rough Country. Ive made that mistake and end up paying more in the long run.

2” in a JL gives enough room for 37’s. You went 4? Well, better get some axles and 40’s since you now have tiny tires again.

I’ve had a jeep jk for about 6 years with a 4 inch lift and after about 2 years of it being lifted, on a trip to Michigan from Tennessee, the front driveshaft started binding up to the point I had to pull over and take the front driveshaft out. I now have a aftermarket front driveshaft and never had that problem again. Definitely need a aftermarket driveshaft 😂. I love the jeep build btw. Can’t wait to see you full send build it💯💯

Still so impressed with the lumar film, I need that for my prelude

Lifts always give you more than they say, I bought a 2.5 inch leveling kit for my xterra and it put the front up like 3, so I bought bigger spring shackles to get the rear up level with the front 😂

The real MVP in this video is that foldable table for handling all of that weight from the lift kit haha

Oh yeah!!!! Here we go. No such thing as TOO BIG!!!!

Notification gang!!! 🔥 stay committed!!!

Thanks for another great video Robbie. I can tell this was soooo much work, but we appreciate it 🙏

30 minute Robbie video? Issa good day

nice vid but one think that you should do asap is to replace those stock brake lines with longer lines and some teraflex front brake line anchors (Quadratec Part # 12700.4900)

Pro tip, because of Canadian climate (I'm in Vancouver), since T.O gets so much snow, salt, make sure you check and grease those Johnny Joints regularly. You will be surprised how quickly they can dry up. Cheers

Jeep is looking better and better every video I'm excited for all the adventures!

I had a dream that you got your new wheels for the jeep

That looks absolutely sick!! cant wait for the future of this jeep

Noti gang have a good day

Nice job. Most Jeep lifts assume you have a Rubicon which is 1.5" taller than your Sport from the factory. So you likely got about 5.5" taller from this 4" lift.

Hey man I owned a newer wrangler and did all this a few years ago have any questions feel free to ask. Your gonna want to upgrade the ujoints Thell go probably first, they also make an axel support bushing that you push in the end of the axel tube and it holds your axel centred instead of it being and to have a flex point and that stupid plastic seal is now rubber

Robbie, I’m not sure about the JLU but when lifting a JKU jeep you need a new complete u joint front driveshaft because the stock front driveshaft joint boot on the transfer case side will rip and destroy it self over time.

You should look into dropping your transfer case, that will help the driveline angles a lot. Especially at full droop.

The jeep looks great, love the new lift & color. Your garage floor, did you epoxy it yourself? If so, what did you use?

With the sand make sure u get it out of your frame. It will collect and rust out,

Now I get it “ultimate adventure machine”😂

Ya that is a bold move Cotton. Don’t know if I could ever go that aggressive with a lift.

I'm surprised you dont have a mini fridge for drinks for them long days in the shop

Shoulda got the antirock swaybar, get full travel but never need to disconnect it

Awesome work what will be the biggest size of tires that you will go?

The front axel looks like a front axel from a small traktor with 4wd. The suspension on the jeep is built to be loded down or be towed with

4" doesn't sound like a lot but it is!!! Man it is nice looking. So nice to work on a new vehicle eh and not old rust buckets.

This was a cool video. I had a 4 inch lift on my old Jeep. It really changes the whole look

It looks dirpy with those wheels now. With bigger wheels tho, that is going to look sick!!

Hey Robbie your old truck got sold about 2-3 weeks ago for $44,486 on Kijiji Auto. I just wanted to see if I could find if before it got sold and saved the listing.

The jeep content is pretty sickk keep them coming ma boi

Impress good job welcome to the club . Not too many jeeper fixer jeep with a nice lol watch on

Those joints (I think) are also rebuildable unlike normal heim joints. Those parts look beefy! Remember to grease em all before and after you go wheelin.

Ay! Notification gang!

You need to get that thing undercoated you can already see some minor rust. Just protect it for years and years

Hi for 4ich do u need to change driveshaft? Brake lines ?

“This looks like way more than 4inches” 😉 that’s what’s she said!!!

Well done . Can you temporarily not put sandbags in it for extra weight? To protect your drive shaft .

Dude that jeep looks massive! Definitely gotta shove some 35s under there! Congratulations man you officially have a badass jeep!

Joint joints are the best in the business

question, I have a 4 inches lift kit jeep wrangler unlimited. but now my jeep goes side by side like a boat in the ocean. some people told me I have to push forward the axle. other say I need to change my rough country spring to rubicon xpress spring. I don't have any idea

New subscriber here, thank you for the link to Belltech. Now I know what lift I’m putting on my jeep gladiator. Also you should take a look at a product called autolynxfor your front disconnect. If you’re going to be wheeling your jeep it makes disconnecting your front sway bar so much easier. I put a set on mine and love them.

Make sure you get extended bump stops or your springs can bottom out before the bump stop does its job. Also they might help stop the swaybar from hitting the shock. Edit: Nvm what I said, I see you got new bumps on top of the shocks.

Next you'll be V8 Hemi swapping it (maybe LS lol) for some more low end torque for off the line and horsepower for that interstate highway driving. I know Jeep just put the 392 in them but a smaller V8 that's not $80k would be awesome. Maybe something around the 4.8L to 5.7L V8 would be some nice. Love my 2015 Jeep JKU but it needs a little power. Love these builds the S10 now the Jeep, it you do a BMW Z3M roadster I'm going to worried you are calling me out lol. That's my garage

Loving the jeep content bro. This build is my favorite so far

I can tell by now that your favorite word is ( sick) 🙂 That's sick!

the tab on the nut is called a flagnut

Yes on the full send of this

Those tabs are great but only work when you're jeep in New 😭 they're a nightmare when stuff is rusty bc the welds make it hard to fit a spanner or socket on 😤

are you gonna do a video on your hot wheels wall build?? That would be a nice lil side dinker video!!

Not totally convinced on the jeep, but I’ll watch all the way through to show support

you should use that scratch resistant wrap on ur garage floor

Hi how much you add the blue lift in you garage house ? Can you send me the link or information about that please Thanks

Sweet Jeep

Room for 40's now!!!

Time to get the auto hidden steps next?

do you have to replace the caliper brake lines? Thanks.

Who did your PPF?

about to do the same thing brother 😩

What size tires are on?

This looks like more then 4 inches only heard that a couple times 😂😂

A traditional vehicle that jeep is built quite traditionaly😂😂

God those rokus look so nice on the ls10

Wow! Looks great man!

Looks sick my dude ready for the 37 or 35s?

Hello Robbie, I am seriously considering replacing my lift with this however what is the measurement ground to bottom of frame?

Yay we get new keep mods 🔥🔥👀

Love all the vids Robbie keep it up🔥

Dude wash it with sand paper Just as a test 😂😂😂

Could I use those springs on a 85 caprice

Nice Robbie!!! Now you gotta go 35 or 37, trim/change the fenders and you are ready to hit the trails!!

please tell me your going with some offset on the wheels

The bro gods are pleased

Big boy tire time 😎

How much you paid for the car lift 🤔

Hey Robbie! Can we get an update on how the floor is holding up? I used the same floor but there was a problem with the product and it hold dirt and stains like nothing else. No peeling or bubbling just terrible surface :(

Love the channel - huge fan, but watching him use that janky Rigid driver got me thinking that we got to use the power of the internet to help him out. Message is for Milwaukee tools - Robbie is in need of a 1/2” (or 3/8”) impact. Something like a 2962-20, 2555-20, 2855-20 and maybe a matching ratchet 2558-20. 🎅🎄😀

This is dope af!!!

Also it's cause it is more than 4 inches it should be around the ball park of 5 because the rubicon trim modles are from the factory with a 1 in lift so when they buy a 4 in left they get a 4 in lift but when someone that has a sport or Sahara they get more lift out of it says why your lift isn't correct at all as far as total lift

I like the jeep the way it is.

Looking good!

You can race with it ?

Love it. Looks sick

I've always thought larger vehicles were easier to work on bc everything is just bigger then jeep goes off and add 10 control arms and I'm going cross eyed trying to figure out what is what😭😂

Looks hot. Are you going to put an air compressor in?

💯

1:29 Congratulations on your 1,000,001 Lift Kit install.

Lets go!

What happened to your tailights bro?

I'm still searching for the lift I want with my 2020 2 door JL. Went to belltech and site says no lift for 2020 Wrangler Sport. Both engine options... any guidance you can give?

Adams drive shafts yw

How much?

Get you some 37s 13.5s

Man to high for the size tires you have a 2.5-3 would’ve been perfect

I'm back at the beginning of video

Finally!

Now you should buy some aluminum in fender