Installing a Pfister 1-Handle Bathroom Faucet with a Push & Seal Drain - Brea Collection 

Use a 7/16 deep socket to scr 4:51 ew on the long brass nut that holds the Faucet. In my 1950s house, not even tiny tim could get a crescent wrench up in that tight area. Also, have someone hold the Faucet above in place . Much easier..oh one more thing, make sure the little final tighting nuts down by the white plastic caps..I didn't notice with rust crumbs everywhere that it was above the horseshoe Faucet holder. Thank God I didn't have to loose that long nut with a crescent wrench. Looks really nice when your done. Oh and you may have to partially saw off the plastic nuts that held the old Faucet tight to get it loose. Rigid sells a reasonably priced oscillating saw. Remember, it looks nice when your done.

as amateur as I am, I appreciate a step by step video on installing the Brea faucet. Thank you for presenting it.

I just successfully installed this faucet using this video but the one thing this video leaves out is that you've got to use plumber's tape or some kind of sealant on the water line connections. I did this without it at first and got leaks on both connections. After the tape, no more leaks. Looks really good. Changed the whole bathroom.

"Next is the long nut" that SHOUD NEVER BE THIS LONG. YES, I'M YELLING😂😂😂😂😂😂

Saved my butt! I was taking it out (changing from oil rubbed to brushed nickel) and I was trying to unscrew the thin silver bolt rather than the octagonal sleeve.

Would have been a lot cooler if the lf-042-vngs instructions would have mentioned the water supply lines needed are 3/8” to 1/2” 🙄😤

So, in this case, no plumber's tape is used at all, on all the connections presented in this video, correct?

Great video EXCEPT you are putting the water valve connections on the wrong Faucets. You connected the Cold water to the Hot input and the Hot to the Cold input. I assume you did this for video recording issues. However, you should have changed the video camera etc to make sure you had it match your instructions.

Thanks. I just installed my faucets.

You made it very simple. Thanks

This was so helpful!! Thanks!!

Great instructions, you helped me big time! Thanks

perfect, exactly what I needed, thank you!

Need to see one with putty. That’s what I searched for

At 3:23, how many of you noticed that this step is super hard to achieve, using an adjustable wrench? Am I the only one who has super tight space under the sink?

Good presentation. I had to look for more installatio specifics as the literature with the faucet does not include the information about the water line connections. Technical writers are evidently in short supply.

Thank you so much!!!!

DO NOT disconnect the waterline click connectors after you initially click them together. It destroys the washers and you’re left with a mess.

I installed an Elden faucet, only for the sink seals on the drain to still leak. Now, I'm going to tear it back out and install with silicone. Why I ever trust the manufacturers instructions to not use silicone is beyond me.

Should I wear shoes while installing bathroom faucet? 🤔

This is precisely what I was looking for! Thank you!

I have a question, I instaled the faucet, water is running, however, there is no pressure, or a very week one. How can I fix that? I had a normal pressure before in the old faucet.

I have a question....my lower deck plate has a hole in it. It looks like the hole is used to guide the long mounting nut. But when I use that as and installation guide the two other guides to not line up. Could I get some help with this?

I recommend to still use plumbers pudding

Any video or instructions on removing and cleaning the aerator in this specific model?

To overflow or not? What sinks are compatible?? Anyone?

Bad video trying to put the horseshoe and long nut is a pain in the ass to install and good luck with a crescent wrench.

Great video, but isn't the long cylinder-like nut put on upside down under the facuet?? Compared to the instructions - can someone pls confirm

I have the Pfister Parisa RT6-AMCC, our one is 12 years old and needs a new cartridge, does anyone know what type and where to purchase them in Canada? Or Pfister, where can we purchase a replace RT6-AMCC?

ok I had a water line break on a Pfister faucet. it was part of the faucet ---is there a way to replace just the line and not the whole faucet

the plastic part of my deck plate comes thru the metal part but the part that comes thru is oval while the faucet bottom is round nor do I see a seal on the bottom of the plastic part any suggestions ?

Great video. Wish I had seen this before I paid fortune to plumber.

mine didn't come with the adapter 😤

Where can I purchase the adapter shown at 4:12 ?

AWS

Rather useless when the bottom part is screwed all the way to the bottom of my copper sink and doesn't even come close to tightening it up. Calling Pfister in the am.

Nothing to connect to a 1/2" supply line?!?!?!? Come on man!

WATCH OUT!! DOES NOT COME WITH A TOOL TO TIGHTEN THE LONG NUT UNDER THE SINK.

I didn't notice any plumber's putty on the drain. Is this not needed with this particular design?

My faucet is leaking from the threads of the drain pipe. Did I screw it on too tight?