Installing Bonoss 15mm wheel spacers on my 2023 Honda civic TypeR FL5 

For added piece of mind, I use a small amount of blue threadlock on the factory studs, and then torque to spec. Nice little comparison video!

A note about the 15mm spacers. Due to being only 15mm thick these spacers use a special nut unlike the other thicknesses; this is to insure that the entire nut sits just below the surface that the wheel will bolt onto. Only your hub's stud threads should protude above the surfae into your wheel's voids.

Just install the 15mm Bonoss spacer today. i have torque down to spec as instructed. i want to see how often should i recheck the torque spec ont he spacer and the wheels. Nice video you have done.

A mi parecer, No se cumple el principio De fijación por completo Y esto puede tener un sub viraje, Ya Que el RIN, No descansa en el centrado de la masa, al hacerlo solamente el la punta de los birlos originales con ny poca superficie de contacto , debiendo acoplarse los espaciadores, directamente : de un lado con el Disco y por otro lado En la cara interna del Rin como Lo mostraste al principio del video, Poco antes de instalarlos, Por favor revisa eso, A mi me pasó y las ruedas No se balancearon bien, Lo solucione, Hasta que , rebaje la parte de cuerda sobrante de los birlos originales y es como pudo acoplarse al 100% el espaciador entre el disco y el rin

Thanks for the video. I've installed 20mm ones. It seems as there is understeer now. What is your experience? Any understeer in spirited driving cornering after installation?

Nice color

Thank you for Sharing very informative. RS!

I just installed the 15mm on my stock FL5. Only downside I'm seeing is a little vibration on the steering wheel after 65mph.

Why didn’t you just buy aftermarket wheels with a lower offset?

Please buy and use a torque wrench you didn't show any torquing. I would hope you came back and did it for the sake of your life and others.

🔥🔥🔥

Love the car. I have an FL5 myself and was thinking about running by these spacers. How have they held up until now? Any issues with them?

What will be torque specs? Same as factory specs? Thanks and looks good just ordered a set

what’s he exact color of your car?

Looks great with the 15mm. How are you liking the swift springs?

When adding the bonoss spacers are the torque specs the same as the wheels at 94 ft pounds?

Are you using the OEM size tire??

Hello, do you have 15mm in front and rear? Also, I’m running stock height and wheel/rims. I want to look for a good flush look but I don’t want it to be popping out, I want something subtle but noticeable. Would 15mm all around be a good choice? Would 20mm all around be too much? Please let me know what you think! Thanks.

hey man. do you have to buy them on their ebay page or can you buy spacers through their website? it seems like buying from their website is a little confusing because I tried to order 25mm ones for my car and when I got to the page to place an order I didn't input a credit card number in and i got a confirmation that the order was placed already

i dont understand why a wheel spacer would need cooling

I’m so confused sorry. So those spacers you don’t need to buy extended lug nuts and all I do put those bolts nut on the OEM part and then the new spacers goes into my wheel and OEM lug nuts on it and that’s it? Sorry new to this all

Any problems since installing?

Have you noticed a difference in steering and handling?

Where did you buy bonoss wheel spacers?

are those caliper covers if so can you send the link ?

You should’ve went with 25mm or at least 20 because it barely looks like you did anything but if it works for you right on

Is anti-seize required?

I would have gone 20mm

jesus man put some locktite on that!

Always use a torque wrench! Not a gun as you have no idea how much torque you're actually applying.

I don't recommend it. I had put spacers on my camaro before and it's not even lowered yet the fender hit the tires everytime I run on the bumps. It's not good for your car

Should probably ask why they didn't do that from the factory. Sure it looks better, but does it affect handing or tire wear, particularly at speed? I'd guess one or both. As a comment mentioned, you're better off just getting different wheels with the offset you want instead of half-assing it with spacers. They also sell hormone blockers for kids. Just because someone sells something doesn't make it a worthwhile product. Love to hear spacer-selling bros discuss their engineering testing and why the Honda factory got it wrong. Use at your own risk I'd guess would be the answer. Ahh, I just leave my stock wheels right against the hub, thanks.

Car culture promotes some dumb shit but StANCe would have to be in the top 5 most ridiculous. I would bet this car has lost performance after this "mod"

Wheel spacers are spocom. Buy proper wheels.

What a fail. Doesn't even torque it down and is using those stupid spacers that bolt onto the existing lugs. Changes the geometry of the suspension creates more wear and tear on the ball joints and the wheel bearings and even the axles since it's bringing the wheel out farther from the hub. But do what you got to do for a "look" I see a plastic wrap all over your car also so it all makes sense. 😂