Installing LUA Scripts for External RF modules on ETHOS

Подписаться 9 тыс.

Просмотров 11 тыс.

50% 1

🔗 www.MrD-RC.com 🔗 / mrd_rc
Since version 1.3.0, Multi-protocol and Ghost external modules have been supported. They were joined in 1.4.0 by Crossfire and ELRS external module support. But, if you open the list of external modules on the ETHOS RF screen; you see any of these modules listed.
In this video we look at how to get external RF modules working on ETHOS. To do this, we have to install LUA scripts for the modules that we want to use. I will show a couple of methods for downloading the scripts. Then show how to install them on your transmitter.
✈️ Contents ✈️
00:00 Introduction
00:27 What you see in the RF section as standard
01:02 How to get the different external modules working on the transmitter
01:52 Downloading the LUA scrips
08:17 Getting the LUA files on to the transmitter
10:19 Checking out the RF settings on the transmitter
11:19 Conclusion
Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.
✈️ In this video ✈️
🔗 FrSky TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL
⚙️ FrSky ETHOS Feedback Community: github.com/FrSkyRC/ETHOS-Feed...
✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help RU-vid share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.
✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at / discord
🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows RU-vid that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at / mrd_rc
🛩 If you prefer, you could always buy me a Coffee at www.mrd-rc.com/go/ko-fi/
🛩 I also have merch at mrd-rc.creator-spring.com/ This include branded items as well as general fixed wing RC apparel.
Thank you for your time, and don't forget to fly it like you stole it!

Хобби

Опубликовано:

30 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 103

@spartan3299 Год назад

Love your effort to make all things RC flight clear and doable. You are a great talent and service to the hobby!

@MrD Год назад

Thanks, and have a great Christmas 👍🏻

@los_sitios_de_lola Год назад

This video is very usefull! I was able to install the modules on my twin x lite s radio! 🎉 Thank you so much for you effort making these vídeos !

@MrD Год назад

Thanks, I’m glad you found the video helpful 🙂

@adrianmilanesi9143 Год назад

Great review as usual, just loaded the Multi lua file into my X10S Express it was effortless, waiting for my iRangeX IRX4 Plus to arrive so i can test it out, Thanks again for the time and effort you put in this hobby. Cheers Adriano

@MrD Год назад

Thanks Adrian. I’m glad the video was helpful 👍🏻

@davidsRC1966 Год назад

Thank you as always for great content. Worked like a charm once I followed your procedures.

@MrD Год назад

Glad I could help David 👍🏻

@grumpyrse Год назад

Thankyou Darren, very useful as always. Merry Christmas!!

@MrD Год назад

Merry Christmas, and a happy new year :)

@nonhands Год назад

Thanks! Would not have been able to get my IRC Ghost module working on the TWIN X Lite without this video. 👍

@MrD Год назад

You’re welcome. I’m glad it was helpful 👍🏻

@poul-erikjensen508 Год назад

Merry Christmas! from Norway ! 🎅

@MrD Год назад

Merry Christmas Poul, and a Happy New Year.

@KenSprouseJr 9 месяцев назад

Fantastic video! I am now able to bind my X18SE to any Spektrum receiver! Cudos!

@jeremykg1569 8 месяцев назад

What external module you using? looking to do the same

@greatmatze 11 месяцев назад

this was really useful!!!! thank you so much!!!

@MrD 11 месяцев назад

Glad it was helpful 👍🏻

@markbutler7027 Год назад

Thank you. This video is very helpful.

@MrD Год назад

You're welcome Mark. I'm glad it was helpful.

@brentfairley5156 Год назад

Great video

@MrD Год назад

Thanks Brent

@2007crf450r Год назад

thank you i updated my x20 and i lost functionality of my multiprotocol external module followed your directions and it fixed it now i can fly all my bnf spectrum stuff again thank you so much

@MrD Год назад

Awesome. I’m glad it’s working for you again 👍🏻

@NorthIceMan Год назад

Thanks Darren - get some z-z-z man! Merry Christmas!

@MrD Год назад

Thanks, Merry Christmas Ron

@UncleFesterUK Год назад

Cheers for the vid :)

@MrD Год назад

Thanks mate. Merry Christmas 👍

@Neonbusa Год назад

hell ya thanks for this its been a big topic last few days in the owners group!! please do a video on what flex firm ware is and how it works

@MrD Год назад

I've made a video on FLEX and the installation. I'll be making a second on how to use it.

@helikeith Год назад

Thanks!

@MrD Год назад

Thank you Keith 👍🏻

@heycheckthatout Год назад

If anyone is having issues getting this to work and could not see the different modules, i found the issue. Some radios (mine is specifically an x20s) came with the multi protocol option already available when i bought it. However, after updating the firmware the multi option has disappeared from the module menu and now when trying to put the lua scripts back on to use the multi module again or other module scrips, they are still not showing up. The fix is, in the scripts folder, there is a folder already in there called "modules". This is the old multi lua script and seems to be causing a conflict and is overriding everything else preventing other lua scripts from working properly. If you delete this folder from the scripts folder, leave in all your other lua script folders, restart the radio, you will now be able to see module options. The general menu is also different than what is shown in the video (im running firmware 1.4.8) and i found i did not need to change anything as the options described in the general menu are no longer relevant for fw 1.4.8 it seems. i was tearing my hair out trying to get this to work and have found zero info anywhere else. Hope this helps someone. it should just simply work with out doing anything special.

@MrD Год назад

This is a great tip. Thanks for sharing 👍🏻

@piloto300 Год назад

Great video as always! Where could I buy a multi-protocol external module for X20S? Which one do you recommend? Thanks

@MrD Год назад

Thanks. I don't use those modules, so can't really comment. But a lot of people use the iRangeX IRX4 Lite.

@JamesHurd Год назад

I am still stuck on Open Tx 2.2 😂 Happy Christmas!

@MrD Год назад

Wow, that is ancient!! Still, those DS planes won't glue themselves back together ;) Have a great Christmas mate

@phillasbury9336 Год назад

Thanks for the video dude! I followed your steps to get my multi protocol module working 👍 However, I don’t see and RSSI or any indication of the RF connection at all! Can you help?

@organiccleanfoodconnection 2 месяца назад

Thank you so much for the video getting closer. But when I bind the models, I cannot figure out the channel mapping. It’s like there’s no real throttle. Any suggestions on what I’m doing wrong? Thanks

@kalps2608 Год назад

Appreciate it. Thankyou. How do you run a 3rd party script apart from the module ones? How do you access the scripts after installing it in the script folder? For e ample lior’s Battery script.

@MrD Год назад

The installation is the same. I would imagine that these are views in widgets on the main screen.

@madsloper 4 месяца назад

Thanks for putting out these helpful videos. I ran into an issue when copying the ELRS script into my X20 Pro, I copied it into the scripts fold within a subfolder. The ELRS header didn't appear in the RF "type" pulldown but was found in the protocol type pulldown under the "twin lite pro" header. I wasn't sure if it was going to work with this RF type header so I remained the main.lua file to include ELRS and pasted it outside of the ELRS folder but still in the scripts folder. My reasoning behind renaming the file was that the multi Lua script main.lua was already present in the scripts folder and I didn't want to replace it with the ELRS main.lua script. I powered off and powered back on the Tx and low and behold the script was in the RF type pulldown like you had shown in this video. Do you think I'll have any problems with the way I installed the script? I don't have the module yet but should be arriving any day now. Cheers!

@martinhall9142 11 месяцев назад

Thanks for this helped alot - slightly unrelated but is there a lug for Inav to show telemetry on Ethos - Yap appears to not work with Inav and Ethos I want to see satellite numbers without needing goggles

@MrD 11 месяцев назад

Not currently. The Yaapu LUA with the AHI is for ArduPilot. I do know that FrSKY are trying to get an INAV LUA developer involved, to get the INAV LUA working on ETHOS.

@CarlSmith-wg8gp 2 месяца назад

Hi Darren a quick question,I’m trying to set up my ix4 lite and you are saying put it into the script on the transmitter,how do you make the script or can the download for the ix4 be added another way .thank you

@embededfabrication4482 Год назад

are all these irx4 lite modules on ebay the same or is there a good one to buy? can we control spektrum DSMX with multiprotocol now? when you install this module does that switch the TX to always use it even for frsky 2.4 receivers or can you take it off and go with the oem config?

@MrD Год назад

Being eBay, who knows. iRangeX are a company. But I don’t know if their stuff gets cloned. DSMX is in the list of supported protocols. But I don’t have a module or Spektrum receiver to test. www.multi-module.org/basics/supported-protocols No, you set the RF on the model to use the external module. Then set up the actual protocol you want to use. For FrSKY 2.4, use the internal module. The exception being if you want to use D8, which isn’t supported by the internal ISRM module.

@richardwangler3367 5 месяцев назад

I have an older Taranis X9D, and have bought a new 2.4 ELES Bandit module. Can I still get audio telemetry read out? Like audible RSSI Voltage etc? Like with the original accst FRSKY protocol? Is this what the LUA scripts are for? I didn't really hear a concise description of what they are and what they are used for

@Pete_Harris Год назад

Informative video thanks! Does a module exist that will enable me to use Spektrum Receivers with my X18?

@MrD Год назад

The multi-protocol module should do that. It is worth checking the supported protocols on the particular module you buy. Here is a list for MPM in general. www.multi-module.org/basics/supported-protocols

@Pete_Harris Год назад

@@MrD Thanks a million! : )

@usetech2133 Год назад

ok Thanks

@heartland3845 Год назад

Will the iRanger IRX4 Lite, or the FrSky module work with the X18 with Spektrum RX's? Ar636, AR631 and AR637T.

@MrD Год назад

To be honest, I have no clue about Spektrum receivers. The list of supported protocols are at www.multi-module.org/basics/supported-protocols If they’re DSM2 or DSMX receivers, they should be fine.

@michael88997 11 месяцев назад

I got elrs setup on my 18se however I can’t figure out how to setup a low rssi warning on it

@trcjr4030 Год назад

Can u show how to set up spektrum safe receivers on your x20s with multi protocol module Thanks

@MrD Год назад

Sorry, I don't have a multiprotocol module or Spektrum SAFE receiver. You should just need to assign a switch to the correct channel to change your modes. You would set that up in the ETHOS mixer with a free mix. Then output that to the channel that the SAFE receiver is expecting the mode switch to be on. I guess that information should be in a Spektrum manual for that receiver.

@usetech2133 Год назад

Hello Darren thanks for your help how can add Lua Telemetry INAV script on X20s ethos

@MrD Год назад

There is no INAV LUA script for ETHOS yet. Only OpenTX and EdgeTX.

@chriswu6174 Год назад

Did you ever get around to checking out the ELRS LUA script? On my twin xlite, the configuration screen is empty, and I can't get the module to bind even though the versions ands bind phrases are the same.

@MrD Год назад

Yes, it’s working fine for me. I have used the internal and an external module for ELRS.

@chriswu6174 Год назад

@@MrD Very strange, but good to know it's working. Any suggestions that might solve the problem? Maybe a better question would be if your configuration screen is blank too? Thanks :)

@MrD Год назад

No, I get everything populated, and can change settings. One thing that was left as a comment. Check your scripts folder on the SD card. If there’s a folder in there called modules. Delete it. This is older LUA scripts, and they conflict with the newer scripts. So that may be causing your problem.

@brentfairley5156 Год назад

Does any of these lua script have to be updated at any time in the future and if so is it the same process as you showed in your video?

@UncleFesterUK Год назад

They get changed from time to time, just keep any eye on the history on the right, that give the last update. :)

@adam_mawz_maas Год назад

Yes, they may get updated from time to time, and third parties may publish improved versions, especially of the MPM script. Same basic process to update, copy the new script to the right location and restart the radio

@MrD Год назад

These two guys have covered it. Thank you both.

@brentfairley5156 Год назад

Thanks guys

@mariocafaro8324 Год назад

Hi, Nice video. Could you help me please? I have a Problem I can't understand! After creating the scripts like you did and saving them on the SD Card, I tried to bind with a Spektrum SPM4650; the led on the receiver becomes steady but the multiprotocol module is as if it weren't connected to the receiver, in fact the signal on the X20 remains at 0. Can you explain me why? Thanks in advance

@MrD Год назад

Sorry. I’ve not used multi-protocol or Spektrum.

@organiccleanfoodconnection 2 месяца назад

When I flashed my module, it kept saying I needed a updated boot loader. So I tried updating and it said the same thing. I loaded the file and things will bind, but I cannot get the mapping correct. Is that because of the incorrect boot?

@Redski69 Год назад

hi ,your site is amazing , still i'm no computer wizzard , i've the ethos - twin lite S , but i want to install some lua scrips , you make it easy as it shown ,is there a another way ? thx

@MrD Год назад

Thanks Andre. Unfortunately not. This is the only way to install these LUA scripts at the moment. I have asked if they could be installed by checking boxes for the LUA scripts you want in ETHOS Suite. I think this would be much easier for everyone.

@finn4795 Год назад

Hello, i have a question. I have a irange irx4 lite and it works fine but i dont get rssi. Is there a way to show rssi? Greetings Finn

@MrD Год назад

This should be fixed in ETHOS 1.5. It has a milestone for that release.

@BlancNikita Год назад

Hello, thank you very much for this video! I would like to install the Multi Scripts into my radio. I tried to follow your video but at the end when I look into "RF System" > "Type" the multi is still not appearing. Is it possible that it does NOT work because I am trying with a iRX4 lite external module ? Thank you for your answer !

@MrD Год назад

No. But you may have put the script in the wrong place. I know that it does work with the iRX4 Lite. Which transmitter are you using?

@BlancNikita Год назад

Thank you for your answer. I am using the Twin X light transmitter

@MrD Год назад

You will need to check in System > General and see if it is expecting scripts on the radio or the SD card. Then you would need to create the scripts folder on that drive. Don’t forget to restart the radio after copying the script over.

@tonybeverley5406 3 месяца назад

Hey Darin can you show me how to get voices back on my x18se,I think I changed the name of the folder in the radio from en to something would that have wiped them,because they still show up in the radio under file manager but I can't get them to work in 1.5

@dfourmed Год назад

Hey D! I can not for the life of me get this to work. I'm running an X20S, latest FW, followed these steps as you did them and ELRS will not show up in the type/protocols. Actually when I go into general settings to see if LUA is run from SD or Radio, I can't even find that screen. I have placed the file into both and still nothing. I'm dying to use this system but going thru hell trying to figure it out. Help please!?!?!?

@MrD Год назад

On the X20/X20S/X20HD you don't get the option for storing on the radio or SD card. That is only for transmitters with NAND storage.. On the X20's SD card you should have the folder /scripts/elrs/ and in the elrs folder have a file called main.lua. That contains the actual script. If you open that file up in notepad and the first lines don't read: -- Express LRS Module local translations = {en="ELRS Configuration"} the contents of the file is incorrect.

@emmanuelsab1095 Год назад

hello darren is it possible to install the LUA INAV script on X20S ETHOS?

@MrD Год назад

Not currently. The LUA Script would need to be rewritten for ETHOS. Unfortunately the transmitter firmware developers haven’t standardised the LUA commands.

@techFPV5964 Год назад

How do i bind the frsky D8 to the Taranis QX7 ACCST Tx?

@MrD Год назад

It will be the same as the ACCST method. Just choose D8 instead of D16. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2QL7DWcH1G0.html

@antlerhanger Год назад

Another great video .. Get some rest .

@MrD Год назад

Thanks Allen 👍

@skychenkoishengsheng6641 9 месяцев назад

Hi i have a hard time to add the lua script to my x20hd.....it judt doesn't show up in my external module...what am i missing here....😢

@MrD 9 месяцев назад

They’re probably just in the wrong folder or have been downloaded incorrectly. First check the folder. If they’re right. Open the LUA file and make sure that’s good. I’m sure I have an example in the video of how the LUA should look.

@skychenkoishengsheng6641 8 месяцев назад

Thank you@@MrD

@N8904V 8 месяцев назад

Does INAV LUA telemetry work with ETHOS Frsky X18? Im asuming it is not out yet?

@MrD 8 месяцев назад

Not currently. Nor is there an ETA.

@N8904V 8 месяцев назад

@MrD Thank you, for future upgrades would you use Edgetx or Ethos? I do use arduplane and a little INAV. Just trying to find the best radio to use Telemetry widgets.

@MrD 8 месяцев назад

This is something that I am thinking about for the future. At some point I will need to update my Horus X10S Express. It’s currently still on OpenTX. But, development for that is virtually nonexistent. At this point in time, I would go with ETHOS. I really don’t like EdgeTX in its current state. The UI is really not nice to use if you don’t have a touch screen. Plus, ETHOS is touchscreen compatible and has a nicer UI. There are also things that are in ETHOS but I noticeably miss in OpenTX/EdgeTX. The Ardu LUA script from Yaapu works fine on ETHOS. I’m hoping that the INAV LUA will get a port at some point in the future.

@N8904V 8 месяцев назад

@MrD Thank you, for the great comprehensive answer.

@MrD 8 месяцев назад

You’re welcome

@rkelley8475 Месяц назад

Step by step every step . I have done this a few times and it's still not working

@spartan3299 Год назад

Dear FrSky, Why don't you give your potential customer base a boost by giving them choice? Choice of operating systems, namely OTX, Edge TX and ExpressLRS. Why would a viable growing supplier of equipment ignore such an enthusiastic and growing segment of the hobby with which you once dominated? Your radios operate, look and feel great. What purpose is served by making a LUA script mind numbingly complicated when almost anyone can do this, mapping, INav, Ardupilot, TBS ect. ect. ect. by dragging and dropping simple files.

@MrD Год назад

I can understand some of that frustration. I have actually asked FrSky to incorporate these RF LUA script installations in to ETHOS Suite. I think it would be so mush easier for pilots. Of course, other scripts, such as mapping, INAV, etc would still need to be installed manually (as they are with OpenTX/EdgeTX). These aren’t in a central repository, so there’s not really much choice with that. However, I don’t think FrSky need to support OpenTX/EdgeTX. The developers of EdgeTX could make a target. But to be honest, I’ve seen countless posts on Facebook where people have asked “If I install ETHOS to my X10, can I go back to OpenTX if I don’t like it?” The answer is of course yes. The ETHOS bootloader fully supports OpenTX still. But, they don’t change back. I swear I’ve not seen a single person change back. Why? Because for 95% of things, ETHOS is as good or better than OpenTX. There are a couple of places where ETHOS isn’t there, like flight mode settings (especially trims), global variables, and a couple of minor details. But for most things, it is there. And, unlike the latest version of EdgeTX with it’s sausage finger interface, it works well for touchscreen and regular screen. I will not update my X10S Express to EdgeTX, because the new interface is horrible for regular LCD screen. You have only a couple of lines of information, because every has been made huge for touch. I still use OpenTX on my X10S Express. Purely because of being able to disable trims and reassign them to other functions, depending on the flight mode. But, I do find myself getting frustrated when I use it now. Some things are just much nicer with ETHOS. As for ELRS. It has been supported since ETHOS 1.4. You just need to install the ELRS LUA script to activate the RF part. Though I have no idea it the setup LUA works with ETHOS. That’s a 3rd party LUA made by ExpressLRS. So it’s really up to them to make sure it’s compatible, if they want people to use their products with and ETHOS transmitter.

@spartan3299 Год назад

@@MrD My daily driver is the first run Jumper T16Pro MPM running ELRS 2.4 on the latest OpenTx, I have an Eachine T16S running Edge, but it is a backup for the much maligned Jumper ribbon cable X10 clone that just keeps going. So far I haven't missed touch screen for anything I do, but while playing with it I don't see any major issues. Not being able to easily read my color screen in the sun plagues both. I am cheap though, My Original fist run X9D was a hand down, and these 2 T16 TXs were on sale for peanuts.

@MrD Год назад

Whatever works for you 👍🏻 At the end of the day, so long as we’re all enjoying the flying, that’s what matters. Merry Christmas and a happy New Year. Thanks for all the comments too 👍🏻