Installing Trim And Ridge Cap on DIY Shop Building Kits

Подписаться 18 тыс.

Просмотров 185 тыс.

50% 1

Now we are installing the trim and ridge cap on one of our DIY Shop Building Kits. Here is a look at how we do it!
Get your Building In A Box kit here: www.buildinginabox.org
Build It Yourself With Our Easy To Assemble Kits
Thousands of our buildings have been built in Arkansas, Missouri, and Tennessee. We are able to sell our kits at affordable prices because we make all of our products on site. We manufacture trusses, make our own metal roofing, and buy lumber straight from the mill.
Follow us on social media
➡️ Facebook: / buildinginabox
➡️ Instagram: / buildinginabox

Хобби

Опубликовано:

8 апр 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 22

@saucesgalore 9 месяцев назад

Finally to this stage

@atchmon902 Год назад

I'm prolly gonna have to special order the trim for the roof cause no hardware store in my town has it.

@Chruch14 4 года назад

That’s great but what about the end of the rake trim would you mind pointing me to a video that shows how to finish that?

@Boeing767Driver Год назад

Do you use the foam closures at the eaves if the building is insulated?

@Day12My Год назад

Did you not watch the video?

@traviscampbell7455 7 месяцев назад

No butyl tape needed under rake trim on roof?

@bobbydelaura 3 года назад

How did you make that cut on the rake trim at the peak? I see hthere was another question, however, without any reply

@stankles7688 3 года назад

It seems he was using a pair of tin snips, maybe he cut it with that? Just my guess unless the piece came cut like that already

@Mikemetalroofing Год назад

you just knotch the bottom and it bends. as simple as that

@dustinworrick9173 11 месяцев назад

I was wondering the same, and finally figured it out on my own. For anyone else wondering make a 90° cut center of peak and cut back the reveal side at whatever angle you roof rafters were. Mine was 50° so I did a 50 and 90 from the same pivot point, and for the roof side, make a mark on center and cut 45 each way going outward (only on angled and screwing flange) so the metal can bend and not interfere with itself.

@juanmojica8469 2 года назад

How moch does it cost

@jmsjro6 3 года назад

How the heck do you make that cut on the rake trim at the peak? I don't want to make a mistake and have to drive 4 hours round trip to buy another piece.

@EricFapton 3 года назад

You would put the piece on the roof on one of the sides. Mark it exactly at the peak. Use a square to mark a line on the face of the metal that would be straight up and down from the peak to the ground. Take the metal off and cut that line. Cut that line all the way to the 45 and your metal will bend into place once you put it back on the roof.

@bLaZeRs4dub 3 года назад

@@EricFapton i kind of get what your saying it’s not you it’s me. can you show a video of you doing that cut on the ridge cap

@joeyarbrough1956 2 года назад

That top cap looked good but he didn't put corner trim up first😱

@cepedaruben1 3 года назад

What's wrong with screwing ridge cap at every rib rather than every other rib? Trying to a short cut here isn't recommended due to sudden wind gusts, etc..