Iztoss/Welugnal Universal Speedometer Set Up and Calibration | Cafe Racer Rebuild 

WIRING 0:57 CALIBRATION 2:06 Hope this helped! Cheers!

Thanks for this video, 4yrs old and still helpful.

Black wire="Electric door lock" is Chinese English for switched power supply. So, power coming from your key switch. This will switch on the unit. Red=connect to a constant power supply. Hope this helped someone.

If you want to be very accurate. Put a chalk mark on the tire and the ground sit on the bike and roll it forward put another chalk mark then measure the distance. This will be equal to the circumference.

when I bought my '82 cb750f recently, i was really happy that it came with crash bars. they might not be the most aesthetically pleasing things, but protecting the motor is always worth a small sacrifice to the look in my opinion. saw your video of the crash, glad you walked away and the damage to the bike is really minimal considering it was a high side.

set 1 is the circumference of the tire set 2 is the magnets placed set 3 cylinders set 4 fuel resistance set 5 odometer reset

Thanks really useful, Lost my wiring diagram so your videos came in very handy 👍.

2:06 very informative.

Legend!

This was useful. Planning to get this for my CB750 DOHC. Subscribed, easy to follow and easy to listen to. Cheers!

Thank you! 888 allowed me to switch it from kmh to mpg.

Hi Mango thank you for the video's it is very helpful. I have the same speedometer and installed all the wires with your help from the little blue paper :) When I went to drive to check the speedometer it says continu 0 km/h, ( Im from Holland). The light on the sensor is on and showing red, but whatever I do it is not showing my speed. I thought this was the only plug for plug and play. I have insert all the correct calibrations and played with but still no change... What am I doing wrong?

Hey Moto Mango, referred to your video when I installed mine 2 years ago, great help. Just today I burnt my speed sensor output terminals, water got into the 3pin connector that connects to the magnetic sensor. I was wondering if I should jump a power line from elsewhere to power the magnetic sensor but I need to check what voltage that sensor runs on. My guess is 12V, and wondering if you could help measure yours. Thanks

I have watched several videos for similar gauges. They seems to have different wire colors and different set ups. Some dont have a code, just hold the rear button on power up. I wish you tested the speedo to know what your doing before video. The glare didn't help either. Thanks for the information.

i'm really hoping that tomorrow when i config mine that the password is the same! because i've been searching the internet far and wide!! and have come across this video after 2 days!

Hey mate great work Just wont to ask something,my cb400 sf tachometer has rpm over 12000. The universal on the video stops at 12000. Any issues?

hello I mounted everything, I just can't figure out how to calculate the circumference can you help me? my wheel is 120/70 r17

I was wondering if anybody could help me I’ve got the exact same speedo I’ve wired it up but it says I’m idling at near 8000 rpm which clearly isn’t right any ideas ?

I would love to have the Amazon link to this speedometer.

Hi Great video. How is the visibility of the display during day light? Does the odometer is just for a trip that can be reseted or there is the bike total milleage which can't be reset?

I bought 1 in shoppee here in philippines..installed properly and all the wires are correct but after 5 months its malfunctioned..not accurate at all..Im on full tank but the indicator is empty,and even the bike is running its still 0..Do i have to change the whole digital speedometer?

How do you know which gas gauge will be compatible with this speedometer to be able to read the gas level?

Where did you connect your rpm wire to? I tried everything and no luck.

Thanx this was very helpful

this may be a dumb question but i want to make sure that im doing it right, im setting up my diagram that im gonna follow and i want to make sure that the negative gear connection wires all go to ground or the negative terminal on the battery, ive already figured out what wire does what but im just making sure

Is wheel diameter from the rim size or the tire size. I have a GSXR front end conversion and planning on doing this speedo/tachometer also?

Hi i have a stock electric tacho and i wired mine to the stock wiring but my tacho won't move. Should i try to take pulse from the ignition coil?

I have a question regarding the wheel perimeter. We put in the diameter of the rim or the diameter of the position where we have installed the magnets

Very well explained...👌👍

Hello, Where to connect the wire from to show the transmission gear indicator, because there is only a neutral transmission to the terminal on the diagram? Yamaha xv 750

Has your mph ever fluctuate like says your doing then goes insane to like 50 back down to 20? And got my rpm signal wire hooked up but the rpm gauge is slow af and not responsive as good

when you are measuring diameter of the "wheel" - you mean rim right? not rim and tire?

Hi Mango, I have this installed on my keeway cafe racer 152 which is a sensor type for speedo but the first time i mounted it 1st gear i am already running at 100km/h then i had asked someone to install the magnet and my speed wont go up to 7km/h. adjust the 60-65 LC setting on the speedo i still have the same outcome. your thoughts might help thanks!

I can't get the RPM to show correctly, It always shows my idle at 8k ant when I twist the throttle a bit it goes to 12k, I tried setting the "pulse" in the speedo settings from 2-9 still shows the same RPM, I can't get the "pulse" to the 1 setting, when I do that and check the settings again it shows 2 not 1? I can't get it to save on the 1 cylinder is what I'm saying.

Love this speedo. Bought it for my Triumph Legend TT. However, it is a 3 cylinder bike and I believe this Speedo accommodates 1, 2, and 4 cylinder bikes. Would you recommend I connect it up as a 2 Cylinder and rpms will just be a tad low and slightly inaccurate? Any wisdom there would be hugely appreciated. Thanks!

Hi! I have a problem. Shortly after starting the display of the speedometer turns off, and I don´t know why. Could you please help me. Thanks in advance.

Hi sir. I need your help. the positive and negative are already connected. but the digital display doesnt appear. what should i do.

no shiftlight ? gearindicator if stock bike dont have this thing dont show gear?

I've just bought that, very good. Do u know if I have to use this speed sensor or can I try use mine original? I'm trying the original, but nothing changes......

Could u let me know what should i put on my bike its 4 stroke 2V cylinder for the engine menu also the wheel diameter on my bike is 1645mm And i have the same speedo just in mechanical movement not digital just for the speed

Got the same thing no password needed but it said u can set your odometer but it dose not set it

really good video (uuhh) (gsh) glad you figuered all this out so I don't have to. Wouldn't mind seeing where/how you mounted the speedo magnet/sensor Ride safely

I order the kilometers per hour is there a way to change it to mph or do I have to return it?

Hi did u get the correct settings? Mine is circumference =1839mm Diameter =23.1" / 58.7cm

Hi. Thanks for the video. Do you know if there is a specific distance from the magnet that the sensor needs to be? My gauge came with no instructions at all. Any assistance would be greatly appreciated 👍🏻

Thank you really Thank you.

Thanks for the great video! I have the same speedometer and I am trying to install it on my Honda CX500. I am a bit lost though as I dont know from where should I get the power line for the speedo?

Hi.. I need help.. my speedometer is the same but the menu is different compare to yours.. my menu is exactly the same as your instructions.. if I’m using 4 magnets, what will be the reading for F00.0? Pls help

How to measure the wheel size ?

can you tell me please it can work with 2020 Honda rebel 500 ?

Hooked this up. And the turn signals and indicators wont flash when I hit the switch. They just stay on based on position of the switch. I've had l.e.d. signals and lights all around which worked fine prior to this speedo install. (With stock guage cluster) I have an 82'Honda cb900. Please help!

Can you just use this Speedo or do you need some kind of electrical box for it? (I'm a total noob)

I bought a similar model everything working but odometer. Any suggestions to check?

I have the same speedometer, my wheel Cir. is 184cm but the speedometer read 5km/h over my GPS speed. Should I lower my wheel Cir?

Hi, great videos about this digital speedometer. I've solved the stand light problem (no indicator light) simply spilling out the stand light signal from the bulb cable itself. But at the moment I'm experiencing another huge problem: everything works fine, but when I start the engine the bike positive signal (I assume) switches from battery to alternator and the entire speedometer goes down. Ok, blinkers, "N" and other lights are still fine, but neither back light nor display are on :-( any clue? Thanks anyway!

I can only get my neutral light to work kms. I connect say the running light and it displays the cluster regardless if it's on or off. 79 GS750. Theres 2 wires to each bulb which might have something to do with it

Hey.. I tried fixing this .. in my RE Himalaya.. but I couldn't figure out how to fix the speedometer connection to the meter.. can you help me on this.. did u changed the wheel speed sensor.. or did u used the one which came with the package..

Hi. Do you have any ideas on how to fix the fuel sensor? Mine doesn't work properly. The guage is fluctuating

Mine has the same settings as yours, but. My speed goes from 0 to something like 18 Km/h while running and then goes down to 0 again don't know why

Hi. I got the same one. I got 2 magnets on my rotors and a 17in wheel with a 120/60 tire. But I can't seem to get it calibrated right. It's always way above the gps reading. Thank you

hi i'm sorry i hope you could respond, I'm curious about the product, can you mention the diameter of that speedometer? was planning to buy one but I'm too afraid that the size of the product is too big

I just installed this yesterday. The one I got has different software though. You can not change it back to 1 cylinder if you change it to 2 or 4. I accidentally changed it to 2 cylinders. I have a 4 stroke 1 cylinder. At first it was doubling my speed, but I changed the number of magnets in the software from 2 to 3 (I'm actually running 5 though.) The speed and rpms seem to be perfectly calibrated now. That's all I changed in the software was the magnet count. I ran my rpm wire to the ignition pulse on my cdi. So now I'm wondering if the number of cylinders really matters. Would it effect the rpms or the speed? Also, I'm wondering if the 1 cylinder mode is for a 2 stroke, and the 2 cylinder mode is for a 4 stroke. Maybe that's why it is working on my 1 cylinder because it is a 4 stroke. Any thoughts on this. People are telling me it can't be right. But the speedo is GPS verified, and the tach seems to be showing the right rpm range for my engine. Thanks

Hello. what are the set values for honda cbf500?

Where did you mount the speed Sensor? I cant find a good Place to Mount it. got a cb too...

If your bike has a drum brake, you might not be able to calibrate it. I have a cb250 cafe racer, the only place to put the magnet was on the rim. That diameter is too great for the range in the computer...so mine reads about 10mph off at (40mph when you are going 50) I wish there were a way to make the gas gauge stop flashing, but I was able to get the N, turn signals, rpms all to work.

Hi buddy ... I recently bought one of these speedometers and all I'm getting is the neutral light after the tachometer does it's initial sweep and nothing else it's not even lighting up. Can you help please

hello why inside my universal speedometer,.. is moistureng i don't know why,.. after washing my caferacer,.. and then ther are moistureng inside

Hi what about the readability of the screen in daylight conditions? Thanks

another question for you, what did you wire your "RPM" wire to? coil positive?

Hai.. I still cannot do the speed calibration... Can you inform me detail again... My wheel include tyre is 64 cm diameter

Can figure out why the led parts don't light up. (The blue and white parts of it. Not the indicators or brights)

@Moto Mango; buddy could you help with the circumference of the front tyre as my speedometer RPM is gone beserk. My tyre size reads 90/90 18. Any help would be appreciated. Need help with the video time 2:51

Hey did you connect the wire wich says position lamp? What that means exactly?

can you please tell me if you can change the tachometer.I need it to say over 80.000km otherwise it will fail inspection!

Hey man, don't wanna bothering you, but did you find any solution for the gas indicator blinking "empty"? I've got the same problem... I don't have a gas sensor, I don't care about knowing the level but this blinking on the speedometer is very annoying.. I'm trying to find a solution to keep it constant, even it doesn't correspond to the reality... Thanks!

Hi, how do I connect the tachometer on sv650 to Iztoss speedometer

Hi Mango! Can you understand those instructions being english mothertongue? .. WTF is "Electric door lock" on 9 pins connector??! Thanks a lot!

Hi sir.. do u know whats the proper setting for keeway superlight 200

Why it keeps reseting? When i off it? I comming back to 180 lc

What did you connect the tachometer sensor to?

i have different mode and the instruction is not clear. the "door lock" is for the wire from the key ignition switch. or the "ACC". That's a hard translation of google translate from the Chinese characters written on the instruction i got. 😅

for some reason I'm not able to get into the settings of the speedo, I long press the button and all that happens is it changes from KMH to MPH. HELPPPP

hello, help I can't run the rpm counter, my motorcycle is a yamaha virago 750 83

Where did you hook up the RPM wire in your wiring loom??

PLS HELP! When I put the bike into gear the speedo turns off.. :\ it’s only on when the bike is in Neutral

How can I make work the fuel level indicator, I been calibrating acording my manual and doesnt work, plz help

They forgot about 3 cyl bikes :(

How did you enter the milage?

negative black is also ground isit not ?

Is there a way to reset the whole setting. Trying get to cylinder 1...

Bought one for my cb400sf didn't instal it yet! My problem is that the Speedo doesn't have any coolant temperature indicator (very essential for old bikes think so). Any ideas?

I was hoping to get some help here because the person who sold me this isn't helping... I've gotten everything to work except for the speed sensor!!! I removed the connector and now I'm left with the brown, blue and black wires from the sensor itself... could anyone tell me what exactly those three wires do? when I first plugged in the 3pin connector it doesn't work, no speed readings at all. the rest are fine.. help!!! 😅😅😅

its trial and error then..about the cylinders i mean? its 0 or 1 or 2 you dont even know. for 4cylinders its 0 or 1?

Good bro! Is the neutral wire is connected to negative wire?

i got no code and no paper work atall with mine !

Hai..anyone know what code for my keeway rkv 200???

My friend can write what works in the settings respectively, I will try to do my own language if I could not do any one I would be very grateful if you helped

Teria o manual de configuração para repassar! Por exemplo ID 888 e o resto das configurações.

My backlights is dying :(

And still no rpm responsivness test!