No video :(

Kia Ceed, Hyundai i30 - crankshaft position sensor, snímač klikové hřídele

Подписаться 518

Просмотров 17 тыс.

50% 1

Kia Ceed , Hyundai i30
vadný snímač polohy klikové hřídele - výměna
faulty crankshaft position sensor - replacement
defekter Kurbelwellenpositionssensor - Austausch
несправний датчик положення коленвала - заміна
uszkodzony czujnik położenia wału korbowego - wymiana

Опубликовано:

10 июл 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 15

@miroskal2593 Месяц назад

Super video 👍👍👍

@uNople Год назад

Followed your instructions for my 2009 i30, worked a treat! Thanks!

@FrySVK 2 года назад

Super video, presne toto ma postihlo s mojou Ceed, ťažké štarty, slabý výkon motora, po výmene snímača ide auto ako nové, úplný iný zážitok z jazdy a aj problémové štartovanie to vyriešilo.

@eliOOO1- 2 месяца назад

Dobrý deň ,ôže ten snimač mať problem auto vôbec nechce štartovať ?

@FrySVK 2 месяца назад

Tažko povedat, je to jedna z vecí, ktorá pri štarte sú potreba. Isiel by som minimalne na diagnostiku.

@eliOOO1- 2 месяца назад

@@FrySVK Daval som ukazalo tento problém potom už vyplo nechce auto natočiť sviečky dal nové čerpadlo počuť nič ide ide ide ale nič z ničoho nič auto šlo ráno šiel už som nemohol natočiť Dakujem za odpoved

@bobcat2378 2 года назад

Thanks for the video very helpfull.

@Igor_ZG Год назад

Nice video! I only have to figure out, how to come under the car. Can I do it only from above??

@Martin-vy2hr Год назад

hezke video, dik

@gernotskupin8472 Год назад

Vielen Dank für das Video!

@glicerinaldehid Год назад

Hello I have a question my car stopped during running on the highway right after I started the Aircon. Could it linked to this sensor? The engine when I want to start is really trying to start up but seems like no gasoline is coming. Could it be this sensor is something related to the fuel pump? Or spark plugs?

@marcusr8017 Год назад

just replaced mine on a 1.4 2015 kia ceed...car wont start now!....got a PO335 crank sensor pending fault ?...faulty sensor?...not touched anything else

@Amhrepairs Год назад

does the engine speed value show during starting in Diagnostic? if nothing is displayed (engine speed is at 0) the problem is somewhere in the wiring or a bad - unsuitable speed sensor. If it shows engine speed during start - the problem is somewhere else, but from my position it is imposible to determine where

@marquesmazucanemacie7303 2 года назад

Wonderful vídeo, My engine have problem is not start The check engine sinal is not on at pinel. Wat can Ido??

@Amhrepairs 2 года назад

ideally, it is good to use OBDII diagnostics, and check the engine speed during start-up. When the revolutions show, there is no problem in the crank sensor. It happens that the immo light flashes during starting, that would be a problem in the coil of the ignition switch (video will be coming soon)