Kia Soul Fuel Injector Cleaning DIY: P02xx Codes Fixed!

Подписаться 29 тыс.

Просмотров 8 тыс.

50% 1

Product Links:
eManual: geni.us/eManualOnline
Use code Dansway22 for 22% off!
Fuel Injector Pulser: geni.us/Fuel_Injector_Cleaner
ODB Scanner: geni.us/ODB_Scanner_WIFI
Thumb-Wheel Ratchet: geni.us/Thumbwheel_Ratchet
Torque Wrench: geni.us/Torque_Wrench_250Ft_Lb
In this video I cleaned / replaced the fuel injectors in my 2013 Kia Soul. Lots of steps, so be sure to watch to the end for the reassembly process. Please comment below with any quesions you might have or other suggestions to those who are doing this also. Be sure to give this a thumbs-up if you found this helpful as that is a huge 'Thank You Dan' to me.
Chapters:
00:00 Introduction and eManualOnline.com
3:08 Fuel Pump and Battery Cutoff
4:20 Getting to the Fuel Injectors
12:50 Removing Injector Rail
16:43 Remove and Examine Injectors
18:19 Cleaning the Injectors
22:37 Reassembly
33:19 Battery Connection and First Start
The links above are Amazon Associate affiliated which means that without costing you a dime, I get a few dimes when you use these links.
Thanks so much for the support!
Dan
dtdw@danholt.net

Авто/Мото

Опубликовано:

6 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 42

@mrd.808 Месяц назад

I appreciate you, Boss Dan for making this RU-vid episode.

@gerardodonaire699 3 месяца назад

Excellent excellent job 👏🏻

@DansWay 3 месяца назад

Hey, thanks for the comment! Did you get this done on your car?

@gerardodonaire699 3 месяца назад

Yes sir with your help was easier. I didn’t get the injector cleaning tool but I put new injectors oh and also I cleaned the valves.

@DansWay 3 месяца назад

@@gerardodonaire699 Awesome! How did you clean the valves? Did you remove the head?

@gerardodonaire699 3 месяца назад

I didn’t it so deep but I removed a lot of gunk and oil . I used carb cleaner and air compressed. With each valve closed I noticed each cylinder was clean

@juana.deabreu464 5 месяцев назад

God bless you bro❤

@DansWay 3 месяца назад

You too!

@renman3426 5 месяцев назад

Thank you so much for posting this I'm getting fuel in my oil I have leaking fuel because of the fuel pressure regulator is faulty sending too much fuel to the fuel injectors which makes it back out and spill over onto the o-rings of the fuel injectors corroding them and then seeping into the engine and then getting into the engine oil. Can you point out to me with a fuel pressure regulator is located? Iran that it's on the driver's side of the fuel I did replace the fuel rail pressure sensor which is on the left side or passenger side of the fuel rail. I replaced the fuel rail pressure sensor. But now I have to replace the fuel pressure regulator which is on the driver's side of the fuel rail. Is there any way you can point it out to me on your video where that's located? I would really really appreciate it! Thank you.. RENMAN

@RajVeer87156 4 месяца назад

Try to look for manual online

@NURsMec 2 месяца назад

I subscribed your channel. Great video. Very informative. By the way how many mileage your car has?

@DansWay 2 месяца назад

Hey there, this Kia has about 120K miles as I recall.

@NURsMec Месяц назад

Im trying to clean my kia soul 2015 injector and i have cleaning kit. My injectors nothing come out when i press the pressurized carburetor cleaner can, at the same time pressing na continues pulsating tester. Any idea?

@jbeckva499 3 месяца назад

Hey Dan is there a good PN for just the replacement O rings? Going to give this a shot on a 2020 GT Line Turbo. TIA!

@DansWay 3 месяца назад

Hey there, you will definitely need to go through a selector tool that takes your exact year/make/model/sub-model in mind. Go to a Autozone (or similar) and get the exact right part.

@johnnytoy5487 2 месяца назад

Thank you 👍 now I need to find a video of the 2013 KIA Sportage.

@DansWay 2 месяца назад

Sure! Let me know what the differences are... I haven't worked on one of those yet.

@obnoxiouscreationz2523 Месяц назад

I have a 2015, your sportage having jumpiness on acceleration that comes and goes?

@jamesphilip4562 2 месяца назад

Sucked for me because I had to slightly move the alternator to give me enough space to come out with the fuel rail

@DansWay 2 месяца назад

Ah man, bummer.

@gsxellence 6 месяцев назад

Hi 🤗. You didn't want to try a cleaner first (bierman B12/lacquer thinner/Lucas fuel stabilizer mix, or BG 44K)? That noise that you heard that scared you at the end of the video sounds like my idle air controller clicking and buzzing on my spectra 😋, however it's not drive by wire. Is the escape a 3.0, love to see more💪

@DansWay 6 месяцев назад

That could have helped much earlier in the deterioration process, but that cylinder was barely functional at this point. I chipped off a huge flake of crud from the injector when I first removed it. Thanks for the comment!

@DansWay 6 месяцев назад

Is this what you are talking about? geni.us/BG44

@gsxellence 6 месяцев назад

@@DansWay oh my I'm sorry that happened. I've been working on this Mazda 6 for a while now and I might have the same issue too regarding the injectors getting clogged up with so much crap due to lack of oil changes and maintenance from when I purchased it last year. I did initially do the Bernie's cleaner wishes I think CRF and cro 505 cleaner switch get help out. Using the endoscope I can see that the cylinders were getting cleaned but I had a lot of carbon on cylinders two and three on my 3.0. No wrong I'm glad you got it fixed the chorus I just hate you had to go through that trouble in that such a small amount of space.

@DansWay 6 месяцев назад

@@gsxellenceLooks like you are getting it cleaned up. If you open it up, let us know how it looks!

@gsxellence 6 месяцев назад

@@DansWay sadly I'm at a standstill because I just had ankle surgery so I'll be out for probably 4 months or so. I just have left trying to fix those stupid OCV seals. I thought I had it fixed because the replacements don't fit in an OEM guides it popped out and one of the boats stripped. So I'm going to get creative using some RTV and I guess some lock tite epoxy or JB weld. That was one of the reasons why I was asking about your Ford escape If it was a 3.0. those are definitely easy to work on compared to the sedans with the VVT solenoids.

@eddyalanis6947 5 месяцев назад

Where did you buy the spacers between fuel injector and cylinder?

@DansWay 5 месяцев назад

Are you referring to the Green o-rings?

@jeffersonjcoat Месяц назад

@@DansWayDan they looked like a washer . U picked them out of the hole , after removing old injectors

@BCEngineer321 4 месяца назад

Query, did you remove the skid plate from the front of the engine?

@DansWay 4 месяца назад

No…? I don’t recall it having one. Perhaps it is missing…

@BCEngineer321 3 месяца назад

Yah there 6-8 bolts and four clips that hold a skid pan on place. Removed it and bam 5 minutes later the bottom cable bracket bolt was off

@DansWay 3 месяца назад

@@BCEngineer321 ok, cool, thanks for the update...

@limitzone4074 4 месяца назад

What year is this and engine size?

@DansWay 4 месяца назад

This is the DGI 2.4L 2013 motor as I recall...

@mrd.808 2 месяца назад

Ah yes, GDI injector replacement

@irisbaez1972 3 месяца назад

You almost dissembled the motor to do this. WOW. That is why we need to learn mechanic things to know what the Hell to buy. Better buy a car buy how maintenance must be done instead of looking attractive.