Making a 9mm-5.7mm chamber insert 

It's ok, I have a drill press now 😀

He needs a drill press.

@@ccos720 yes 🙂

@@TheRhinestoneHurricane why do a lot of people say rifle the barrel first even gun smiths say that?

@@ccos720 might have something to do with the land introduction 🤔

Thanks ☺️

@@Mihail2204 Thanks, the 5.7 case has a dual radius neck so it’s not difficult to round out 🙂

C'est pas faux,😉 22 lr,maxi ,au dessus 🤔 boum 😮

Thanks

@@TheRhinestoneHurricane Спасибо за видос! А я таких придурков которые в такой агрессивной форме пишут комментарии сразу блокирую, удивляюсь твоему терпению)

​@@Tik.Tak.Просто твою херню никто не смотрит, там и блокировать некого😂😂😂😂

5.7x28mm is a center fire ;)

@@paulromsky9527 thanks ☺️

I used grease on the first bit, the hardest one to drill through ;)

👽😉🖖

I use a drill press know ;)

@@joshualuna3515 I suspect most people click on this video thinking I’m making a gun, you’ll just have to wait for that video 😉

It’s designed to fit inside the barrel, can’t be very thick 😉

Laienarbeit! Das hast du sehr rücksichtsvoll gesagt! 😂 Passender wäre Pfu***

Of coarse its amature work... or he would use a lathe. That doesnt mean he did a bad job though

I used a roller from a photo copier 😛

@@tomspeed2000 I have used those but this one had to be drilled out of a solid bar 😉

Ну плешивому диктатору ты же веришь или нет? Хотя он только переобещать обещаемое обещать гаразд.

Метод рабочий, но дрочево... и точность, так себе.

It’s a chamber insert, it goes inside the barrel 😉

Yes but what a cool hole :P

worst job, not safety and accurate and good.

​@@TheRhinestoneHurricaneشسسظظظظظظظظش

@@mattivirta you're just mad he has the balls to do this. 😘

😂😂😂😂

I don’t have a lathe 😪

@@TheRhinestoneHurricane Печально. Если вы занимаетесь такими работами, то он вам просто необходим. Впрочем, этот станок и для других работ весьма востребован.

I do it all the time, no big deal :)

@@TheRhinestoneHurricane Sorry brother, but the visible run out on that bar stock in the opening seconds-that alone-would make it all but impossible to keep a drill bit perfectly centred.And I doubt that anyone could manually hold a drill chuck sufficiently steady as to maintain accuracy to that degree. If it was that easy, wtf would we need engineering lathes?

@@ratheanach5545 You can be believe what you want, I just grind out the goods 😎

😂🤣

The chuck that you push forward with the bits in it, is that set up on a little block or something? Whatever your doing is working man.

Thanks ☺️

Nope, relies on chamber integrity ;)

Thanks, I have a drill press now 🤗

America 😎

Thanks, 5.7 is technically a 22 ;)

Allein schon daran merkt man dass der keine Ahnung von Metallbearbeitung hat. Was dann folgt ist noch schlimmer.

@@Bluesmann1 Ja und? Mach das mal mit so einem Setup 😂

I don't use this method to make chamber inserts any more, I have a drill press now :D

goos good. you bought or diy?@@TheRhinestoneHurricane

@@mitropoulosilias bought it 😊

Thanks, I’m also working on a pen gun 😈

Não amigo. Pior é não fazer, dar desculpas que não tem ferramentas adequadas. A maior e melhor ferramenta ele já tem, que é a criatividade. Parabéns a ele.

M

Thanks 😊

I do use a bit of grease on the bits 😉

We don't need no stinkin rifling B)

Thanks, you should check out my playlist 🙂

Works for me 😊

It’s not a barrel, it’s designed to go into a barrel 😉

The whole reason this video took off is because it’s over half an hour 😂

Sometimes ;)

Even oil would no longer help with the technology. He lacks more important fundamentals.

Yes you are right! don't understand the positive comments. Apparently most people don't understand what they're seeing.

It would have to be a blank, can’t any holes drilled in it 😉

@TheRhinestoneHurricane I do know they have barrels with no holes. I got 1 cheap for a 380 I brought back to life. But you're like me. I like to try and make my own stuff.

Making your own stuff is quite fulfilling. Your sense of pride in creation is a remarkable feeling.

Untraceable

Ерунда, но ты победил в том , что сумел полчаса нам пропудрить мозг,браво.

Good thing its a 5.7 instead of a dutch flintlock caliber then!

How so 🤔

I don't think so, the 5.7 case should be fully supported :)

@@TheRhinestoneHurricane The AK chamber tapers 1mm in diameter along the length of the casing until the neck is reached. Obviously a taper aids extraction of the casing. I get the point about firing a 5.7mm round down a 9mm barrel, it isn't going to be a good experience.😂 You'll have to show the results.

😂nice sarcasm.

Muchas gracias! ☺️

Thanks ☺️

@@TheRhinestoneHurricane Can't wait to see some test firing on a range

@@doejohn8674 I already tested it 😯

@@TheRhinestoneHurricane I saw the other video with the blank cartridge, but did you try it with live ammo?

@@doejohn8674 I don’t have any live ammo, probably too spicy for the derringer 😬

I tested it with a blank that I made :)

@@TheRhinestoneHurricane Great. Just be careful testing live... fingers are priceless but strings (to pull the trigger) are cheap... :)

I don’t know what’s fake about it, I tested it 🙂

а че ты так сагрился на него? пусть делает что хочет, он еще и доброе дело делает - помогает новичкам освоить кустарное оружейное дело

"Здать" - ЕГЭшник)))))) И Сдают только у нас. У автора (США) это вполне легально., там не ссут власти давать право на оружие людям. А у нас скоро рогатки, блять, запретят.

Thanks, it’s pretty easy once you drill the first hole 🥵

First hole, thin drill bit, even more miraculous.@@TheRhinestoneHurricane

I'm not sure it is as perfect as you say.

I think it's always a bit of a gamble but as a principle, it is far more likely to get a straight hole by inserting a drill into a rotating workpiece than the other way around.

well Jozef, that is indeed the right way to do it@@jozefbubez6116