Massimo MSU 500 UTV 

Well, it's been 6 years how did it last ?

Dale.. how's the Massimo doing? ..looking at buying a relative's

Jay Todd my msu did the same thing with fuel gauge, I pulled the passenger seat, then unplugged the sending unit and removed from tank the float was stuck I ran it up and down a few times reinstalled it and it has worked for the last 3 yrs.

Might should have read the break in guide, or stop pulling 1200+ pound loads.

Think again

30 day money back, 6 month warranty. If you failed to return it that's your problem and you can be internet mad till the end of time. Massimo has some quality control issues but that doesn't equate to terrible equipment. Our first one had obvious wiring harness issues, Tractor supply made it right. Now your rant a few post's above says week 2,week 4. Obviously you're a dumbass cause you didn't load it back up at week 2 and make tractor supply give you a new one. Sucker's born every minute.

plenty of power. I use it here in Michigan and works great!

Any way to quiet them down more? ..insulation, more muffling, etc?

Did you have it in low? Trying to spin 4 tires in high rage is really hard in heavy sand

Look up problems and complaints. Literally nothing but PROBLEMS with everything you can imagine. No one will work on them very difficult to fix, very difficult to get parts. When you do fix it the same part breaks very soon afterward. Do yourself a favor use your head invest in used arctic cat, polaris, yamaha, honda or e-ton. Mossimo products are JUNK!!!!!!!!

@@mi5veezee I have a Suzuki King quad I don't have to worry about it but my cousin has one and it gets around pretty decent he's never had a problem. now he's not trying to hot dog it and beat on it like it was a RZR but just for putting around it does pretty good. And we live in Florida so we go through a lot of deep sand

That's why you take it back to Tractor Supply within 30 days for a return. We had the same luck, MSU 500 was a lemon from the start, never ran right, fouled plugs constantly. It wound up at the authorized repair shop where it stayed for 5 weeks and they along with Massimo couldn't figure it out but narrowed it down to the wiring harness. Long story short as far as I know it's still there at the repair shop while Tractor Supply gave us a brand new one no questions asked. The new one is perfectly fine and is a nice machine and runs perfect no issues at all. While we also felt the same way you did before Customer service did the right thing we also realize Lemons happen. I'd buy another one with all these features in a heartbeat for $8000 versus a $12000-$20000 machine.

I've had mine for a year now run the Hell out of it haven't had one problem.

So the Chinese picked the Yamaha to model their utv from...isn't that illegal?

@@jaytodd5809 yeah it is, but they don't care and Yamaha has moved on to newer designs and better UTV. Thier new YXZ are kick butt!!

well i bought one today. Before I did I looked to see if I could buy parts. The parts are easy to get so we will see?

Hi Bryan, my name is Rudy.I have a Massimo 700 bought at tractor supply. You hit the nail on the head when you said they are junk and nothing but trouble.But I`m stuck with it so I was just wondering if you could help me out.Let me give you a quick run down, Week2 blowing white smoke because of cracked cylinder head had it repaired by warranty machanic ever since starts real hard like it has way to much compression, week 4 just shut off no fuel had it repaired burnt wiring harness. I installed a bypass starter relay seemed to help in starting.Now i`m going up a small incline and the wheels started slipping and a slight banging noise (not good) in the front of the engine by bottom of trans.Was told it was the rear drive shaft took it apart only to find out that was not the problem.I have both front and rear drive shafts out.when I turn the yokes by hand they spin freely but when I start the motor and put it in gear I get a grinding noise like a gear is stripped ,When I put it in neutral and shut off the machine and try to turn the yokes there is resistence for a few turns like something is binding.My question is have you ever incountered this problem.I just can`t seem to get answers from anybody and no one wants to work on it.I`m a pretty good wrench I work on all my own equipment, Was just wondering if you had any information on this.Oh ya this machine has very little hours on it and its not abused at all.Any help you can give on this problem would be appreciated. Thanks : Rudy

Hi Rudy, I don't know if you remember me, I am Lance, I work for Massimo, we met in the mens room at the gay bar, you were dressed like a girl, anyway, I tolf you to bring it down to the shop and I would fix it under warranty, see you soon!

Hey did Lance fix that after all?

Look up problems and complaints. Literally nothing but PROBLEMS with everything you can imagine. No one will work on them very difficult to fix, very difficult to get parts. When you do fix it the same part breaks very soon afterward. Do yourself a favor use your head invest in used arctic cat, polaris, yamaha, honda or e-ton. Mossimo products are JUNK!!!!!!!!