Mazak TPS Button Function 

I ran a t2 mazak for 10 years and never knew how to use tps. Think the t1 controls had same too. Back when dinosaurs roamed the earth. Thanks for the video.

As usual i like your videos, very informative for both beginners and trainees. I would like to see a video about how to set up a new tool, tool data, to avoid cutting deep with a tool that cannot go deep. Many who don't know the correct way just put in 0.

That's very useful, thanks for your videos, one day I'll write to you some questions about this type of control, I'm a new one on this lathe 😁🙌🏻

Thank you so much !!! Finally I know how to use TPS function 👏🏼👏🏼👏🏼👏🏼

thanks, your videos are helpful, im an apprentice in a small company and the only tradesman who use to run the machines left so ive got alot to learn and theres alot of little bits and pieces im missing so thank you.

Copy option work done.....Thanks a lot 👍

Ha. No more cutting air for me! Thanks!

Thank you

I Love your videos Best regards from peru

Thank you wish you health success

i hope you make tips&tricks of mazak any more. Thank you very much my Professor.

fantastic.

Just a warning, when you rapid straight down onto the job, you have a chance of rapiding into the job if your previous insert was heavily worn. I like to move away in both directions, and on my mazaks they will feed down on the hypotenuse of the x and z movements.

this is so handy my smart 300 has this is great just be careful I broke a carbide 1 x 12 bore bar in a bore my fault so be sure what you doing big deep bore incerts wear out have to change tps 123

Hello and thanks for all your help! Do you have a video on the TPC button? An area I am struggling with. I have. T32-3 control and a T-Plus control. Thanks Phil!

thanks mister

For sub note reference would you be willing to list machine/controller specs in video summery? Machine: Series? Controller: T2, T3, Other? Very informative video btw. As most of this content can be used Controller to Controller with slight variations in user interface/controls seen in later models of Mazak's turning machines.

thanks you Sir. Your video is fantatic

Thank you sir.

OD Threading mazatrol 25x1.5 length 29.0mm

it's essentially a save state. TPS allows you to "load" your game.

Cómo puedo comunicar el PC con la máquina?

Can you use TPS a few passes back. Just by pressing feed hold, handle, move X.200 away from cutting surface, then TPS, move Z.100 back, then TPS and X and Z again then a insert change. Will the machine let you restart the cycle in the middle of the canned cycle a few passes from the cutting surface.

do ¥ou know TPC ? ? how to change it? what about a video on machine and user parameters?

Thanks alot Is there any way to approach to the workpiece more gently instead of G00ing

Please show how to copy unit, program, program sequence in same program as well as in different program

That i am looking for

Hello Phil. I was reviewing your TPS button video and am wanting to try this on our Mazak 350 II as I have never done this yet. I am sure it it probably different on a newer machine vs the old but similar in ways too. I would like to ask however if the turret can be rotated to access an upside down held tool during this TPS movement cycle? Your example shows the insert side up and easy to access. Many times our tools are upside down and can't see the screw untless the turret is rotated to get to them and then return to the cutting tool position desired. Can you please advise on this as I am interested in knowing more.

Phil, how to reduce chattering?

hi . I have a Mazatrol t1 , but the key board and menu are another language and manual is different language . how can I change Manu language to English . thanks🙏

When you change the insert you have to touch the tool off again on the tool eye .

Phill how do you use the tool pack clearance function on a mazak 640t fusion lathe

For Nexus 645 qtn

hi, i have a machine mazatrol cam-T2 in german language..plz tell me how to change language in English..

Can this be used in single process mode as well as auto?

can I request Mazatrol T33-2 tutorials for wheel reprofiling of mazak

Can this function be used on eia/iso programs?

Plz spline cpy command

...