Тёмный

Mercedes W123 Engine Deep Clean - Steam Clean - Restoration 

Restore It
Подписаться 540 тыс.
Просмотров 247 тыс.
50% 1

Go to getroman.com/RESTORE for $15 dollars off your first order of ED
treatment.
In this episode, I make a start on the deep clean of the engine and gearbox as requested by the owner. The engine starts and runs well and so a full restoration was off the cards for the owner in this case. I partly strip it down and steam clean everything before it gets ice blasted and rebuilt with new service parts in episode 2.
There's one more episode on this and then it'll be ready to go back into the finished car, which is also close to being finished. It's taking a lot more of time than I planned, so that's why things are a little slow, but during the next project, I'll have more help which should mean more consistent episodes.
Thanks for watching. Subscribe for more!
#restoration #Mercedes #engine
Tools & equipment used:
Quartz Lacquer - goo.gl/8PTVKM
Base Coat Paint - goo.gl/mWhufG
Rust Remover - goo.gl/13gopW
Rohr 250 Welder - bit.ly/33mkOGP
Workbenches - arborgardensolutions.co.uk
Moldex Full Face Mask - goo.gl/NNYGrv
FGL 5 Spray gun - goo.gl/Acg5rd
A.N.I. R150-T Mini Spray gun - goo.gl/cHTJS2
Colad Washable Overalls - goo.gl/3Css9E
Colad Mixing Cups - goo.gl/8DYmE8
Colad TurboMix Sticks - goo.gl/cYZfks
Colad Synthetic Paint Strainers - goo.gl/H79ZgL
Follow me on Social media to keep up to date with videos and behind the scenes.
My Patreon Page:
/ restoreit
My Twitter Page:
/ restore__it
My Facebook Page:
/ restoreitchannel
My Instagram Page:
@RestoreItChannel
PayPal Donations:
Restoreitchannel@gmail.com
Discord
/ discord

Авто/Мото

Опубликовано:

 

2 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 157   
@hellbillypete.7898
@hellbillypete.7898 2 года назад
I might have an oilcooler..i think its for an 230, but its look like the same size. I will check it out tomorrow. Btw, i live in Sweden, and if you pay for the shipping, its yours for free! :-)
@jeffhammond8969
@jeffhammond8969 2 года назад
For the cooler, could you use a fin comb tool to straighten the fins and repaint the outer housing?
@matthieupaire3853
@matthieupaire3853 2 года назад
Your videos are always great! As an old Mercedes fan I loved it.
@danielprivate7442
@danielprivate7442 2 года назад
4:53 oi, those timing chain sprockets are really really worn. See the way they are bent over and even broken at the tips? Might want to think about replacing those. Great episode.
@RestoreIt
@RestoreIt 2 года назад
Thanks Daniel, I wish this was my project haha. I'd replace so much. But cheers I'll tell the owner and see what he says...
@KhanIlkara
@KhanIlkara 2 года назад
Despite that, for the age of the engine it seems pretty well taken care of. Sure they get old and worn out and replacement would do it good, but I'm surprised at the lack of well, destruction here.
@danielprivate7442
@danielprivate7442 2 года назад
@@RestoreIt Well, if the client doesn't want to shell out money for a new part, you might be able to do this: If the sprocket is simply keyed to the cam AND if the hub is symmetrical (no offset) you could turn the sprocket around and gently file the tips that are gnarled over so the chain seats nicely. Just don't forget to transfer any timing marks to the other side of the sprocket too. That will buy some time before the part fails.
@Nbomber
@Nbomber 2 года назад
@@danielprivate7442 damn, thats a neat idea actually.
@shakedinbar2162
@shakedinbar2162 2 года назад
that was so interesting ! i wish i had all the tools and spacework to get similar stuff done too
@TheNorthernmunky
@TheNorthernmunky 2 года назад
Very satisfying to watch! Awesome work
@Pedro5antos_
@Pedro5antos_ 2 года назад
Awesome content! This project is turning up pretty great
@hajdarsalihi4215
@hajdarsalihi4215 2 года назад
Hey man look on autodoc for the oil cooler and you can get one for a w116 Is not the exact one and it has top and bottom inlet/outlet connection but with some slight modification you can make it fit. I did it on my w123 and it sits nicely. Good luck
@repairrestore3293
@repairrestore3293 2 года назад
As always, a great restoration 👍
@andrewedwards6548
@andrewedwards6548 2 года назад
Always makes my day seeing an upload from you 😊
@vessmachineen193
@vessmachineen193 2 года назад
I always enjoy watching you work. a nice job like always.
@Famouzlastwrds
@Famouzlastwrds 2 года назад
I appreciate how his clips don't have unnecessary music playing on them
@stephenansahoyirifi7827
@stephenansahoyirifi7827 Год назад
I like the way this gentleman works keep it up
@sonyhk3824
@sonyhk3824 2 года назад
Great job. Cheers 👍
@punkbloater
@punkbloater 2 года назад
Very satisfactory to watch, all though I was just at the dentist today and removed a tooth and that high pitched dremel sound brought back bad memories. 😳😁
@philbaier
@philbaier 2 года назад
Please include window seal replacements in a future video! I have a 300CD and love these videos so far.
@electronic7979
@electronic7979 2 года назад
Excellent restoration
@nickwhitney1534
@nickwhitney1534 2 года назад
Satisfying to watch.👍
@Radio4ManLeics
@Radio4ManLeics Год назад
My goodness! You are clearly a very patient & painstaking man!
@markdaugherty6378
@markdaugherty6378 2 года назад
Great progress, looking forward to the next episode. Once again, great camera work.
@ezequielsilva2709
@ezequielsilva2709 2 года назад
Muito bom!
@MrSHAUNE55
@MrSHAUNE55 2 года назад
I used to work on loads of those 110 engines years ago, always needed valve guides and seals.
@EnriqueLopez-hb5jn
@EnriqueLopez-hb5jn 2 года назад
Awesome information to restore that engine back to new condition.
@mythicalcadmus8023
@mythicalcadmus8023 2 года назад
I cant wait for the E30 to finish
@tattoosteveneo
@tattoosteveneo 2 года назад
Just a friendly. Never grind valve covers or manifolds unless you flatten them before install. Since you haven’t done that yet I would recommend it. Good job on it so far.
@MrHBSoftware
@MrHBSoftware 2 года назад
´the wire whell doesnt take off material...i use it in the shop to clean off old gaskets and sealer on valve covers and sumps and if you look closey it doesnt even remove the machining marks...you just have to use a not very aggressive wire wheel and dont force it, obviously
@cookie_boi
@cookie_boi 2 года назад
great going champ 🤜🤛 as for the cooler, get a reputable radiator joint and ask them to either repair the one you have or make a better one (more cores) usually they come up with a better bigger and more durable solution also look up forums until then, keep the grrat content coming 🥃🥃
@dearlord4990
@dearlord4990 2 года назад
Amazing job
@winsurf2971
@winsurf2971 2 года назад
very very impressed by the job
@PB-wb2kj
@PB-wb2kj 2 года назад
You can use a fin comb for radiators on the oil cooler.
@johns8000
@johns8000 2 года назад
I would go with Hydroblasting to clean up the parts , it also takes off rust and doesn’t leave pitting like sand blasting. Didn’t know about Ice blasting before this video.
@rominou684
@rominou684 2 года назад
Hello :)! There is some time I would like ask to you about, I hope you will don't take it bad. So, why are you using the dremel with a metal brush for cleaning the aluminium part? It's a thing i often see, and it always a paint to watch it as it scratch and alter the aluminium surface in the process. Why don't you use instead some soda blasting on the aluminium part, it's a good compromise for removing greases film and contaminant as paint. That's especially really effiency for cleaning sensitive part as carburators. Always found it (little ;)) damaging your overall resaerch of high quality and clean as possible restaurations. Otherwise, as usual, good continuation to you ;)!
@namenotavailable11
@namenotavailable11 2 года назад
I was going to mention the same thing. You especially don't want to on the mating surfaces.
@pinzgauernorcal
@pinzgauernorcal 2 года назад
I'm looking forward to the ice blasting results!!!
@wojtekdobrowolski8084
@wojtekdobrowolski8084 2 года назад
Will you replace the starter motor brushes as a sort of preventative maintenance or are they not really worth replacing until the starter stops working properly?
@chombi84
@chombi84 2 года назад
Great video 👍
@pascalhogstrom2203
@pascalhogstrom2203 2 года назад
Love it 🥰
@georgeae0
@georgeae0 2 года назад
Hey man! I've seen some pretty gnarly injuries from using a bench grinder/wire wheel without gloves. It makes me scared when I see you do it.... Stay safe
@dietsausage1
@dietsausage1 2 года назад
ive been in a hurry before and once had my index fingered sucked into a bench grinder. it doesnt happen twice. get some pliers and gloves. it aint worth the pain and inconvenience of healing....
@ridethroughlifertl
@ridethroughlifertl 2 года назад
@@dietsausage1 I was always taught not to use gloves on a bench grinder because it can suck your hand into it. I honestly don't know which is correct.
@54mgtf22
@54mgtf22 2 года назад
Me too. It made me cringe.
@dietsausage1
@dietsausage1 2 года назад
@@ridethroughlifertl yeah, i just use them in case the tool slips
@maxbradley9534
@maxbradley9534 2 года назад
Don't use gloves, a thread from gloves caught in the wheel is far far worse than it just catching your bare skin
@bobjoncas2814
@bobjoncas2814 2 года назад
...lookin' good ,stay safe and have a great week....
@RestoreIt
@RestoreIt 2 года назад
Cheers Bob, you too!
@AmazingThings685
@AmazingThings685 2 года назад
Grit job man
@picaspero
@picaspero 2 года назад
Hi, What brand of wire wheel do you use for the dremel? I bought some, but they fell apart in a few seconds of use.
@Peaceof59
@Peaceof59 2 года назад
Aliexpress 2 ~ 5min use (buy set x100)
@MP-nl6he
@MP-nl6he 2 года назад
Awesome !!!!! Job
@RestoreIt
@RestoreIt 2 года назад
Cheers dude!
@kensilelongway2658
@kensilelongway2658 2 года назад
Living one of my ADD dreams. I wish i was doing this so bad lol
@barneykennett9282
@barneykennett9282 2 года назад
Nice...👍.
@isyt1
@isyt1 2 года назад
Great job! Just wondering, where does the grease go when you steam clean? I expected to see it dripping off but it seems to just evaporate or disappear?
@netmatrix75
@netmatrix75 2 года назад
It drips down. You can see he has a large pan under the engine to catch it.
@derverschraubungstheoretik1278
@derverschraubungstheoretik1278 2 года назад
Krass! Wie sauber das geworden ist
@houseofno
@houseofno 2 года назад
May I ask what the make and model is of that steam cleaner? I may want to purchase similar equipment if it's within my budget. Thanks for another great video!
@dariusmartu2619
@dariusmartu2619 2 года назад
It’s worth to remove oil pan clean all and inspect shaft bearings 👍🏻also valves?
@dasautoshoppe6932
@dasautoshoppe6932 2 года назад
The black paint on the bell housing is overspray from the factory, and wasn't necessary to remove. The shift linkage was a non coated steel when new, and was never painted. Only a yellow inspection paint mark on each end would have been present. The Exhaust gas recirculation pipe is stainless steel, and was left bare when new. It was not painted. However, the nuts on each end were yellow zinc plated. In addition, the top of the EGR valve was yellow zinc, not clear zinc (silver). The fan and pulley on the alternator were clear zinc plated when new. They were never painted.
@richardpalmer4936
@richardpalmer4936 2 года назад
What rust converter did you use please?
@radhamesortiz
@radhamesortiz 2 года назад
The fins of the alternator also have to be zinc plated, the exhaust manifolds are originally ceramic coated in a light grey paint ( almost white)
@MichailDoc
@MichailDoc 2 года назад
Oddly satisfying
@stevengysin1392
@stevengysin1392 2 года назад
Which steam cleaner are you using? I've been debating on getting one for my own projects.
@michaelem7883
@michaelem7883 2 года назад
He was telling that SC4 which is a karcher steamer
@ROADKILL4147
@ROADKILL4147 2 года назад
nice job did you look on ebay for that alternative thing?
@CrazyKraut20
@CrazyKraut20 2 года назад
For the love of god please wear a respirator when sanding, cleaning and de-rusting surfaces :/ Love your videos I have already learned a lot about Body work and welding just from watching your work :)
@FhVW
@FhVW 2 года назад
Where do you leave the water with the paint remover? and which rust remover are you using? Here in the netherlands I can almost choose of just 1 remover and 1 reformer..
@robertm5969
@robertm5969 2 года назад
for the heat exchanger, why not use one of those "combs" to pull the metal fins straight again?
@adrianobastardi
@adrianobastardi 5 месяцев назад
I didn't know such a thing as ice blasting existed.
@lepeejon2955
@lepeejon2955 2 года назад
What kind steam cleaner did you use? Excellent video.
@thomasvanonsem8842
@thomasvanonsem8842 2 года назад
Kärcher SC4
@Picard1701ABCDE
@Picard1701ABCDE 2 года назад
Amazing video and what a beautiful finish. In my opinion the M110 is one of the most gorgeous engines there is, simply beautiful.
@user-nr9sl2qq1d
@user-nr9sl2qq1d 2 года назад
👍
@ldenorio
@ldenorio 2 года назад
what are some of the bands you are listening to on your headphones?
@christophermarshall5765
@christophermarshall5765 2 года назад
Something else worth talking to the owner about is deleting the oil cooler. Yes, I did this to my own car, and it is fine. Simply fit blanking plugs & copper sealing washers in place of the oil cooler fittings on the engine. It has no ill effects to the engine.
@goeatapizza2572
@goeatapizza2572 Год назад
Ac automobiles need it
@christophermarshall5765
@christophermarshall5765 Год назад
@@goeatapizza2572 actually they don’t. The ones that are fitted with air conditioning usually have a bigger radiator. Mine has a three core radiator. Non ac ones use a two core, except in hotter regions like Australia, where three core types are used. The oil cooler in my 123 wagon is still there, but is not used.
@pascaljeske7307
@pascaljeske7307 2 года назад
A very good Job Love it really 👍❤️👍
@tahraouiislam3537
@tahraouiislam3537 2 года назад
I work as a mechanic and have 9 years of skill from Algeria. I am looking for a job in your country. I like your country very much. I am 29 years old.
@blazerobbins3958
@blazerobbins3958 2 года назад
What’s the steam cleaner you’re using?
@gr1mrea9er82
@gr1mrea9er82 2 года назад
a couple of old welding sleeves would keep your arms clean from dirt and rust...
@Shalash87
@Shalash87 2 года назад
I am kind of hoping to see you take on the automatic transmission
@aitorbleda8267
@aitorbleda8267 2 года назад
I see you still have a Titan paint stripper can from Spain!
@pmyhill
@pmyhill 2 года назад
You must go through a hell of a lot of the small rotary wire wheels ?
@MrSSSamuelll
@MrSSSamuelll 2 года назад
I also restored a M110. I think you won't get around redoing the head. Valves, valveseals, valveseats, resurfacing, you know the drill... Should be around 2000 Pounds
@abedhiaz3162
@abedhiaz3162 2 года назад
What is the name of this steamer ?
@patsematary
@patsematary 2 года назад
I agree with degreasing and steam cleaning but I would have covered alternator and ignition distributor & other sensitive parts..also rubbing with the dremel and the rotating brush the alloy head cover is not a recommended treatment, hope it was at least a brass brush, not steel
@MrHBSoftware
@MrHBSoftware 2 года назад
there are people who make custom oil coolers and radiators for very cheap...overhere in Portugal you would be looking at about 200€ tops for a custom oil cooler in aluminium and very similar to the original....
@andrewedwards6548
@andrewedwards6548 2 года назад
Hey I have an idea about the rad you want replacing.
@christophe8549
@christophe8549 2 года назад
Hello !… J’savais même pas qu’il y avait des 5 chez Merco ! V’la la pollution avec tout ces produits chimiques , mais c’est le résultat qui compte. J’en remets une couche, vidéo pas finie 😿
@rolandl4782
@rolandl4782 2 года назад
Open connections on the K-jetronic fuel system cant be good?
@drd0a
@drd0a 2 года назад
Better plug up those ports to prevent contaminating the combustion chambers mate
@user-ry5hm7ho8t
@user-ry5hm7ho8t 7 месяцев назад
Don't use caustic degreaser. It will severley attack the aluminium.
@jayinmi3706
@jayinmi3706 2 года назад
That L800 part, is that an oil cooler? That seems ridiculous if it is.
@snail415
@snail415 2 года назад
Curious if you know Sandro over at Auto Craft Car Detailing in Melbourne. He’s practically the best detailer in the developed world. Look him up and his channel up. You guys deserve to have a beer together.
@user-ry5hm7ho8t
@user-ry5hm7ho8t 7 месяцев назад
I wee people spend thousands on these cars getting them like new, then selling them for a lot less than it cost them to do so, just to keep them there. That model next to the rover p6 are worth saving for what they taught us.
@pawenowak8642
@pawenowak8642 2 года назад
2.8 6 cylinders M110
@ibma6658
@ibma6658 2 года назад
👍👍🌺
@_ifv
@_ifv 2 года назад
wear your PPE!!!!
@bokkenrijder172
@bokkenrijder172 2 года назад
I was searching and looking forward to the dry ice blasting video, but it’s nowhere to be found despite that this deep clean video is already 6 months old.
@sverdson
@sverdson 2 года назад
bonjour pouvez activer les sous titres svp ? merci
@RestoreIt
@RestoreIt 2 года назад
Je suis surchargé de travail en ce moment mais je m'y mettrai dès que possible. Ou faire participer quelqu'un d'autre. À votre santé
@alexnike84
@alexnike84 2 года назад
Un saludo desde Lima Perú. Fuera muy bueno que tuviera traducción al español
@StefanJovanovski
@StefanJovanovski 2 года назад
Hey bro, we all feel very manly working on our cars, but I don't understand why you don't protect your hands while working with the grinder 7:50
@frankbiz
@frankbiz 2 года назад
I can only imagine what you could do with a 500 Watt Laser Cleaning machine. You would save many hours of time. Not sure how expensive they are. Have you considered one?
@christophermcelligott1593
@christophermcelligott1593 2 года назад
What am I missing here? 5 cylinders with 6 exhaust ports?
@albertospengler
@albertospengler 2 года назад
Nutela... too worried not to get dirty
@lucasconstantino3884
@lucasconstantino3884 2 года назад
6:38 não fica bravo não.
@fargogemini694
@fargogemini694 2 года назад
Steam cleaner? That’s thing is what my wife cleans in the house with
@filipbrecelj669
@filipbrecelj669 2 года назад
great video but i would change the title to mercedes m110 (.924?) engine rebuild
@mrtube16
@mrtube16 2 года назад
U missed replaced water plug pastile
@user-of3kl1sp7z
@user-of3kl1sp7z 2 года назад
Привет из России !
@user-hi7zl3ex5b
@user-hi7zl3ex5b 2 года назад
Яко
@Z1LVA
@Z1LVA 2 года назад
Do not use bosch spark plugs. This part is poor on quality. Or keep that in mind.l if there will be misfire.
@stephencrozier396
@stephencrozier396 2 года назад
3 wks! What going on?
@user-jr1qf7jg1t
@user-jr1qf7jg1t Год назад
Keep dirt there don't matters.. Still working 😢
@user-ry5hm7ho8t
@user-ry5hm7ho8t 7 месяцев назад
Hit the word "more" beneath the film site.
Далее
Mercedes W123 Restoration | Welding Part 2
16:06
Просмотров 71 тыс.
Mercedes W123 Differential Restoration
18:59
Просмотров 415 тыс.
UNO!
00:18
Просмотров 1,1 млн
Help Barry And Barry Woman Scan Prisoners
00:23
Просмотров 1 млн
Fully Built Subaru STi Engine | ASMR
19:03
Просмотров 786 тыс.
Mercedes Driveshaft Restoration - The Hard Way
22:12
Просмотров 266 тыс.
что за звук?
0:15
Просмотров 3,2 млн
Manual installation process of highway guardrail
0:15