No video :(

Microsoft Surface Pro 4 - screen bulge fixed, battery replaced, SSD upgraded!

Подписаться 582

Просмотров 53 тыс.

50% 1

Own one of the tablets with the bulging screen, maybe even developing a screen gap? Need to deal with poor battery life (or no life at all)? Want to upgrade SSD on one of these ultraportable laptop/tablets? This and a lot more you can find in this video (use the chapters if you want to jump to a specific section)!
So this time around the subject is Microsoft Surface Pro 4 (1724). The device is not exactly new, but I love these Surface tablets, own several and quite pleased with what they can do. Full blown PC with proper OS in a tablet form factor? Yes please! But like many similar devices, over the time internal battery deteriorates. This means poor battery life, but more importantly, eventual battery swelling that leads to screen bulging, often followed by screen delamination or even cracking.
Unfortunately, these devices are not easy to repair. To get to the battery, we'll need to disassemble pretty much the whole tablet, including detaching the screen, disconnecting a lot of things internally, removing the motherboard and then the battery. Then do everything again in reverse ;) And you can see me do exactly that in this video. This means that you can use it to see how to replace the LCD screen, internal components, battery and yes, internal SSD can be upgraded while we're there.
If you want to do a project like this, I suggest to pay attention to the video as a lot of things can go wrong. I would know ;)
Extended worklog version is on the sibling JMI Works channel:
• [JMI wLog] Microsoft S...
Don't forget to like and subscribe if you found this useful and would like to see more. Let me know in the comments what you agree/disagree with, what you liked, what you didn't like, if you have any questions, if you know of a better way of doing it, or if there is something that I absolutely should not be doing or have done ;) All constructive feedback is welcome! ;)
Disclaimer:
This video is only for entertainment purposes. Any injury, damage, or loss that may result from improper use of tools, equipment, or from the information in this video is the sole responsibility of the viewer.
00:00 Intro
00:24 Is it a bad battery in your tablet, or is it just happy to see you?
01:03 Real reason why your device developed a bulge
01:58 I have a plan!
02:45 Different methods for screen removal
05:18 Warning: here be dangerous areas when cutting screen adhesive!
06:14 Cut the screen out
11:41 Disconnect the screen
13:21 That's one gassy battery!
13:33 Why full disassembly is a better way
14:15 Remove antenna support bracket
14:51 Remove CPU EM shield
15:15 Remove heatsink assembly
17:10 Detach camera connectors
18:18 Disconnect power and volume buttons
18:36 Disconnect left speaker
19:00 Disconnect headphone connector
19:21 Disconnect SD card reader connector
20:20 Disconnect power/dock internal connector
21:15 Disconnect right speaker connectors
22:07 Unscrew the motherboard
23:17 Remove right speaker assembly
23:58 Remove the motherboard
24:35 Battery removal plan
25:37 Remove that battery!
28:57 Old battery vs new battery, ouch...
29:20 Install new battery
30:28 Reinstall the motherboard
31:25 Reassemble and reattach internal components
34:23 Clean up and reapply thermal paste
36:34 Reattach heatsink assembly
37:18 Reinstall CPU EM shield and antenna support bracket
37:49 Replace SSD
39:21 Reuse and reapply screen adhesive
40:37 Reconnect the screen
41:03 Glue the screen in place
43:29 Success - thanks for watching!

Опубликовано:

14 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 102

@emcaco Год назад

Omg you actually show the steps of putting it back together! Instead of saying "Just Do it In Reverse" and leaving people to rewind through the whole video. I appreciate it

@JustMakeItNow Год назад

I know, right? ;) Not all operations are easily reversible - e.g. if you break a glass, you can't say "and to fix it you just do the same thing in reverse". But some people complain that videos are too long, so you can't please everyone. I know I personally want to see reassembly, so that's why I put it in my videos. You can always skip parts that are not relevant, but you can't put back something that is not there.

@michaelcaldwell4890 6 месяцев назад

Much appreciated. Got my son's surface back up and running with a new 2TB ssd as well as a new "FLAT" battery. Don't think I could have done this without someone like you!

@JustMakeItNow 6 месяцев назад

Thanks Michael, I am glad that my video was helpful!

@polarbearchp 2 года назад

Thanks so much. Love the detail and the pictures shots were very good. Thanks again

@JustMakeItNow 2 года назад

Happy I could help!

@rrwholloway Год назад

This is exactly what I needed. A proper full teardown and reassembly, including motherboard removal.

@JustMakeItNow Год назад

Glad it was useful, hope your project went well ;)

@rrwholloway Год назад

Sort of. Screen is off successfully, but wow that antenna array is designed to be destroyed on removal! £20 for a new assembly and £36 for a new battery and I should have a fully working surface pro 4 once again.

@JustMakeItNow Год назад

Ha, I know what you mean! Before you splurge on new antenna strips, check if you can simply straighten them up. Unless you straight up cut/tear them on removal, these are just foil strips, if they're just bunched up you can unfold them back.

@rrwholloway Год назад

@@JustMakeItNow unfortunately it’s toast. The best advice i would give others is get a sharp knife and cut as close to the display assembly as you can. That black glue is sticky and horrible

@rrwholloway Год назад

@@JustMakeItNow what did you find was the best way to remove all the glue before reapplying new glue?

@mickstickwheeledwarrior 2 года назад

Thanks for this video just got my first probook after years on older machines and this helped

@JustMakeItNow 2 года назад

Great to hear!

@listendeaf 2 года назад

OMG! Thank you!!!!!! Fixed my problem!

@JustMakeItNow 2 года назад

You're welcome!!

@pabloresplandesdeoliveira8108 Год назад

Incredible!. Thanks for the content, it was of a professional mastery and warned me about the care in the dismantling phase.

@JustMakeItNow Год назад

Great to hear!

@AsusMemopad-us5lk 8 месяцев назад

It's impossible to do such precise handwork with that fast music going on in the background! Would have preferred the walk-through with no music at all, and with closer real-time video of how the little connectors and adhesives come apart. Recommend using an ice cube tray or egg carton for tracking the screws and other small parts in their sequence of removal. Thanks for the video!

@JustMakeItNow 8 месяцев назад

Thanks! You can mute sound and change playback speed in the player controls. The video is already pretty long, and if it would be 1x speed everywhere no one ever would click on it ;)

@pastorlugo121 4 дня назад

Outstanding video. Thanks.

@JustMakeItNow 4 дня назад

Glad you enjoyed it!

@libertadmatos5780 Год назад

I appreciate the info. I just need this video to move a lot faster. Thank you. Brilliant!

@JustMakeItNow Год назад

That's what playback speed option is for ;)

@mohamadabuel-ezz3822 2 года назад

Thanks very much. Very useful and educational video.

@mohamadabuel-ezz3822 2 года назад

Where can I find spare screws for Surface Pro 4

@JustMakeItNow 2 года назад

You are welcome!

@JustMakeItNow 2 года назад

IIRC all the inside screws are T3 and T4 drive, these might be difficult to find for cheap if you're only missing a few. I'd probably just get one of these laptop/watch/glasses repair kits which have an assortment of small screws. Those would likely be Philips heads rather than Torx, but for that kind of repair that won't matter.

@mohamadabuel-ezz3822 2 года назад

@@JustMakeItNow thanks for your reply. I''ll try to find it.

@tonis2u Год назад

thanks you for this tutorial, can you tell me what type of bit you are using on the screw gun. I have taken apart an iMac and have the screwdriver for those screws, I am wondering if it's the same size.

@JustMakeItNow Год назад

I don't remember exactly, but I am pretty sure this Surface Pro 4 used T4/T5 bits (Torx). I don't know what was in your iMac, but there is good chance that it may not work. Apple tends to like using pentalobe screws, these bits won't work on Torx.

@BobsWebofWonder Год назад

Great video! Wish I had seen yours first.. Didn't know about isolating the battery. Now it won't power up. Any idea what has blown can I fix it?

@JustMakeItNow Год назад

Sorry to hear that :( This is not uncommon, unfortunately. First thing, check the battery connector pins, sometimes these get deformed during disassembly/reassembly, and this prevents solid contact. If that's not it, try your old battery (if it worked at all), sometimes aftermarket batteries are faulty from the get go. If none of the above helped, things get progressively more difficult; potential fixes will require hot air station and knowing what you're doing. Couple of common things that go bad during battery replacements are Schottky diodes on the charging circuit, or any number of fuses on the mainboard (some are marked as 0 Ohm resistors). If you're good with microsoldering, check out this page, they have a good summary of potential issues with SP4 power: www.aonemobiles.com.au/2020/03/microsoft-surface-pro-4-no-power-no-schematics-no-problem/. Good luck!

@TubeROfUS 2 года назад

Awesome video! Leaving a like and sub, keep it up man. How thick can the double sided tape be? 3mm too much?

@JustMakeItNow 2 года назад

Thanks for the sub! I actually used exactly 3mm wide tape in this video ;)

@JustMakeItNow 2 года назад

Just to be clear, 3mm is width, not thickness.

@TubeROfUS 2 года назад

I got some that is 1mm thick. The old one does not stick much anymore. Thinking about removing the old tape to make room for new stickier tape. What's your opinion?

@JustMakeItNow 2 года назад

Yeah, if the old adhesive is not sticking anymore, or is mangled up, it is better to remove and replace it. At the same time, you probably don't want to use super strong stuff in case you need to open it up again some time later.

@TubeROfUS 2 года назад

Trying to put it all back together. Good news is it's booting. However, it appears that the screen assembly may have been damaged during removal. I get flickering and lines all over the place. Those ribbon cables only attach one way or is it possible to clip them on out of position? Maybe that's what I did.

@JO-xq3kl 6 месяцев назад

I replaced ed two batteries on two surface pro 4 laptops and they all say battery not detected. they both switch on with ac power but when not plugged in they do not turn on.

@JustMakeItNow 6 месяцев назад

This happens, unfortunately, especially with aftermarket batteries. First thing I'd check if the battery cable is seated properly. If no issues there (likely, as you can run on AC), then you can try to do hard reset, which goes something like this: . - Power off - Hold Volume Up and the Power button for 15 seconds. The Surface logo screen may flash, but continue to hold for 15 seconds. - Release the buttons - Wait 10 seconds - Power on the Surface . Also, while on AC, check if battery device shows up under Device Manager in Windows.

@scottd9448 2 года назад

Mine has only a slight bulge (maybe 2mm in the centre), but it is causing colour issues on the edges of the screen. I'm awaiting delivery of a heating pad & pry-tools. Do you think the screen will go back to normal after replacing the battery? Thanks for the great video!

@JustMakeItNow 2 года назад

Yeah, I forgot to mention that before complete screen delamination, swollen battery pushed up into LCD and this (as well as heat) caused visible discoloration on the screen. In my case, these were large yellowish areas - very visible on light backgrounds. After battery replacement these were completely gone, though it is not a guarantee. Be careful with the heat though, it is easy to permadamage LCD. Just because heating pad is supposed to be temperature controlled does not mean it is necessarily very good at it, especially if not calibrated.

@scottd9448 2 года назад

@@JustMakeItNow I already have an IR laser thermometer to check. Thanks for the tip!

@JustMakeItNow 2 года назад

Just keep in mind that pads may also have uneven heating due to the way heating element is embedded. Keep the temp settings a bit more conservative to be on the safe side, and you may still supplement it with more targeted heat from a heatgun. You should be good as with a swollen battery it is much easier to lift up the screen (which is the hardest part of the process).

@wenshengfan6670 2 года назад

Thank you for the tutorial. But would you please tell me where you purchased the new battery and how much it cost?

@JustMakeItNow 2 года назад

I did buy my replacement battery through the local wholesale mobile repair supplier, so that probably won't be helpful to you. You can easily find these batteries online though, just search for "G3HTA027H" (this is the battery model number). They go for about $40-50 or so. I know for a fact that there are some on eBay, Aliexpress and even Amazon. Probably not OEMs, but I'd say it is still a pretty good deal to restore your Surface Pro 4 back to almost original condition. Hope it helps. Let me know if you have any other questions! ;)

@wenshengfan6670 2 года назад

@@JustMakeItNow Thank you for your reply. I found some eBay seller that carries this model number. I also have a Surface Book (model: 1703 / CS4-00001) with a similar issue. The right side of the screen is bulging. I would like to replace the battery too. Do you by any chance know the battery's model number? If not, is there a way to find it out? Thanks.

@JustMakeItNow 2 года назад

I don't own this model, but I believe there are several battery models that are compatible with your 1st gen Surface Book: G3HTA044H, DAK822470K, G3HTA020H. If you're disassembling your device anyway, the easiest would be to look at the existing battery number to be sure.

@wenshengfan6670 2 года назад

@@JustMakeItNow Thank you very much.

@eedimil Год назад

Hi i have surface pro 4 that is not working and i was planning on removing the battery and put it in another surface pro 4 that has a bloated battery.. Will it work?.. Thanks

@JustMakeItNow Год назад

Well, it depends ;) First of all, are you sure that battery is good in the not-working Surface? It does not need to be bloated or visibly damaged to get bad. More importantly, you'd have to be _really_ careful in removing the one that you intend to transplant - you'd want a lot of isopropyl and probably some heat. The thing is, most of the time when you remove the battery it is quite warped as you pull on the adhesive with quite a bit of force, and the batteries are very thin and pliable. I am sure it is possible, but it might be more work than you think. You can try this first, and then go for a replacement battery is it doesn't work. These batteries are not super expensive.

@AJTHIND Год назад

read every comment , good job. I have this problem with i7 version I'm typing this on. Stupid Question: did you clone the surface before onto the new samsung SSD? Or did the msbios do a stock install? Also same issue with same gen Surface i7 Book Pro

@JustMakeItNow Год назад

Not a stupid question at all, I probably should have mentioned it. Yes, I did clone the drive. Don't remember the details, but I usually just boot up into live Linux from USB and dump existing drive onto network location. Then after swapping the drive I boot into live Linux again and restore the dump, and then re-adjust partition sizes if the new drive has more space than the old one.

@sirJayGee Год назад

Hi. I've done everything exactly as shown but when I try to power it up I get nothing. Even if it is plugged in. Did I fry my motherboard? Blow a fuse? How can I tell? Is it now a paper weight? Thanks.

@JustMakeItNow Год назад

It's possible :( One thing to make sure is that you properly connected the battery, and that the battery is in working order. Without battery connection the device won't work even if plugged in (AFAIR). You may try to connect your old battery if it was working, even if it wasn't working well. If that's not the issue, there is a good chance that you did blow either fuses or some diodes on the motherboard. This is not something that can be easily diagnosed or repaired. If you know what you're doing you can try to check for continuity on fuses (R000) or diodes, but the chances are not high. Unfortunately, it is not uncommon to blow something on the motherboard if you're not super careful with connecting battery terminals - if these are slightly misaligned, bad things happen :( . Good luck!

@sirJayGee Год назад

@@JustMakeItNow thanks for the reply. I think I'll bring it to a professional tomorrow.

@JustMakeItNow Год назад

Nothing's wrong with that, hopefully you'll get it fixed. Would be great if you could post a comment as to what the issue was, in case it would be identified.

@danielb3500 Год назад

I need this fix for my surface pro 4 so bad. It just sits in a drawer now. Can you recommend someone/somewhere that can do this exact fix for me?

@JustMakeItNow Год назад

You're probably better off finding a local mobile repair shop, they should be able to do such job. If you go local, at least you will have someone to complain to if things don't go according to plan ;)

@danielb3500 Год назад

@@JustMakeItNow thanks for the reply! You're a talented dude for sure. I'll check out my local options

@jerryc8135 Год назад

Good morning, where are you located? Do you do repairs if I send my surface pro to you? Thank you

@JustMakeItNow Год назад

Thanks for asking, but at this time I prefer not to accept mail-in repairs for liability reasons. I would recommend finding a local repair shop, so you have better options in case something goes wrong with the repair. Cheers!

@XxSBeeZyxX Год назад

What kind of double sided tape is that? Do you have a specific recommendation?

@JustMakeItNow Год назад

Double-sided acrylic tape, the exact specs are not super critical as long as it fits dimension-wise, so 1-2mm wide with thin carriers. Usually this would be something from either 3M or Tesa, you can see in this video I used 3M 9448A tape, but Tesa tapes (something like 75620) would work just as well.

@XxSBeeZyxX Год назад

@@JustMakeItNow thanks dude

@championmenace 11 месяцев назад

How long does a fix like this last, if it's successful?

@JustMakeItNow 11 месяцев назад

For as long as the new battery is going to function. This depends on battery, usage patterns etc. Can easily be several years if everything goes according to plan, which will probably exceed usable life of the device anyway. If not, replacing it the second time is a much easier procedure (unless you hardglued screen back in :) )

@ShawnKirk007 Год назад

What do you have the temperature set to on your heat station?

@JustMakeItNow Год назад

I had it on the lowest setting - 100C, though the source temperature is not that important. The important part is how hot your screen surface gets, that's why I was constantly checking it with my hand. You can go higher temps, this means you have to reduce heat application time. IIRC screen panels get permanent damage at about 80-100C, depending on screen technology (LCD, OLED).

@ShawnKirk007 Год назад

@@JustMakeItNow Thanks. The kit comes in tomorrow along with a larger M.2 drive. So I'm fixing and upgrading all at once.

@JustMakeItNow Год назад

No worries. Just don't rush and it's going to be alright ;) Good luck!

@DaveS75 Год назад

What temperture setting did you use for the gun?

@JustMakeItNow Год назад

Pretty sure the lowest I could set my hot air station to, so that would be 100C=212F. You can get away with higher temperatures, it is all about how long you're staying over the same spot, and how much you're heating up the screen panel itself. Damaging screen due to overheating is the danger, other components wouldn't be damaged by these temperatures.

@maythesciencebewithyou Год назад

How high is the risk of the battery burning or exploding?

@CEMBerthoud Год назад

Mine powers up but the screen is blank

@JustMakeItNow Год назад

Try to connect external screen, or access via Remote Desktop. It is possible that the screen is dead, but the rest is functional.

@CEMBerthoud Год назад

@@JustMakeItNow I tried that, and it works with an external monitor, the touch function works and the tablet works fine wit the external monitor. the tablet display lights up when powering on but is blank. It's not cracked. I check the display drivers all look good so I'm not sure what to do now.

@JustMakeItNow Год назад

Well, most of the tablet works, so that's a good sign ;) In your case it is most likely one of two things: either internal display cable is not seated properly in its socket, or the panel itself is dead. Just because it is not visibly cracked and digitizer works doesn't mean LCD panel is functional. I'd open up the case, try to reseat display cables and see if that helps. If not, replace the panel as the hard part (opening up) is already done.

@osamabeenllama3021 Год назад

where did you get the battery from

@JustMakeItNow Год назад

I got it from a local mobile repair supplier, but you can get these batteries from eBay, Amazon, Aliexpress and elsewhere. This is a relatively easy-to-find item, look for part number G3HTA027H or DYNR01.

@nynshawty5608 Год назад

Ive repaired dozens of surface pro's there is no need for heat guns. i can take the screen off in 5 min. All you need is a old ID card. Start at the top and swipe all the way around the screen. Ive repaired every surface model without breaking the screen ever

@JustMakeItNow Год назад

You must have some military-grade ID cards ;) I can see how you can cut adhesive cold once there is an opening (which is, in all fairness, the case in this video). This would be harder than heated, but would be doable, certainly if the device was opened before. But if the original adhesive is intact all around (e.g. no delamination yet), how do you start your cut without heat? The whole idea is to soften the adhesive so a part of the screen can be pulled with a suction cup and then you can insert your cutting tool. Without heat, how do you first insert the card in?

@rrwholloway Год назад

So do a video showing your incredible technique…?

@daveys 8 месяцев назад

Not a truth challenge by me, but please could you post a video of how to do this if you’re ever doing one again? I’d like to open my SP4 up and I’m definitely reluctant to break it. Mine has the video wobbling fault.

@jeffreymurillo3131 Год назад

Do you have a business of repairing these?

@JustMakeItNow Год назад

This is more of a hobby ;) Though I do sell some repaired stuff from time to time.

@danielb3500 Год назад

@justmakeit I'd send you mine and pay you to fix this issue on my sp4

@registriert2012 Год назад

why on earth the terrible loud music???????

@JustMakeItNow Год назад

Can't please everybody... ;)

@AJTHIND Год назад

@@JustMakeItNow he was here for the music only

@BrianBaccus 2 года назад

Great information but you just take so long to get to the point I need to fix this not read a novel

@JustMakeItNow 2 года назад

Just like longer videos get comments that they need to be shorter and to a point, shorter DIY videos are full of comments that too much is skipped/fast forwarded, and viewers can't see exactly what is going on and follow the steps. Considering that you can't see what is not there, my approach is to do more detailed videos, and put in chapters for navigation. This way, if you want to zero in on something, you can, and you can skip/fast forward parts you are not interested in. And the viewers who like to see more details can do so as well. And believe it or not, some of us watch these videos for entertainment/education purposes, not because we need to fix something right away ;)