Тёмный

Mitsubishi Ecodan Wireless Controller Connection and Dipswitches 

Dore Woodman
Подписаться 1,9 тыс.
Просмотров 7 тыс.
50% 1

In this video we will show you how to configure, pair and set up the wireless Mitsubishi room thermostat controller and receiver. As well as the pairing we will show you the Dipswitches that need to be changed in order for the system to work.
#sustainableliving #greenerliving #therebuild #renovation #surrey #countryside #buildingproject #restoration #heatpumps #ufh #ashp #gshp #climatechangehoax #newbuilds #greenindustrialrevolution #saveourplanet #renewables #renewableheating #renovations #dorewoodman #futurehouse #youtuber #youtube #pricecap #energysaving
#home #homeextension #tinietempah #climatechange #extraordinaryextensions
#channel4 #energysavings #passivhaus

Наука

Опубликовано:

 

9 сен 2022

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 6   
@RapaciousSloth
@RapaciousSloth 9 месяцев назад
I have the FTC6 and im only looking to hook the heatpump to the MELCloud app. Do i need the controller and the receiver? i already have a wires thermostat for each room in the house.
@annettewhite9011
@annettewhite9011 Год назад
great video, can I ask a question about the pump for zone 2, the UFH. Our manifold and UFH pump it is right next to the cylinder so we are using this pump for zone 2. Usually, this pump is connected to the UFH wiring centre. Using a 2-zone pack from Mitsubishi they say: When adding a second heating zone to a pre-plumbed cylinder the pump for heating zone 1 needs moving from OUT2 to OUT13. Then wire your additional pump into OUT3 Should we wire the UFH pump to the FTC or the UFH wiring centre?
@dorewoodman
@dorewoodman Год назад
Hi Annette, either or on the pump wiring. When a thermostat calls for heat it will switch the pump whether it is from the wiring centre or the FTC as long as the signal cable from wiring centre to in6 on the FTC. I hope that makes sense.
@annettewhite9011
@annettewhite9011 Год назад
Hi, we were so pleased to learn how to do that. But.... switched the HP on and got error EE, do you know how to address that error? is it a fatal error?
@howarddavies1124
@howarddavies1124 Год назад
Hi there. Great video and really helpful. Just a quick question. If I only have a single zone, do I still need to switch off Dip SW2-1?
@dorewoodman
@dorewoodman Год назад
Yes, SW2 - 1 corresponds with zone 1 and SW3 - 1 corresponds to Zone 2
Далее
Mitsubishi Ecodan wireless thermostat not working !
5:09
Ecodan FTC6 Dipswitches
5:16
Просмотров 9 тыс.
2DROTS vs WYLSACOM! КУБОК ФИФЕРОВ 1 ТУР
07:25
Кто быстрее? (GTARP)
19:19
Просмотров 572 тыс.
Mitsubishi Ecodan wireless controller setup tutorial
4:48
Ecodan control board
3:26
Просмотров 7 тыс.
Mitsubishi Ecodan Air Source Heat Pumps
39:20
Просмотров 73 тыс.
no hot water Mitsubsihi Ecodan, Emergency mode
3:27
Просмотров 14 тыс.
iPhone 16 - НЕ СТОИТ ПРОПУСКАТЬ
4:50
APPLE дают это нам БЕСПЛАТНО!
1:01
Просмотров 674 тыс.
iPhone 16 - НЕ СТОИТ ПРОПУСКАТЬ
4:50