Join the Caliber8 Tribe to get a free ebook on 10 simple ways to beautify your home plus more home improvement and diy tips- join.caliber8.com Get the Ultimate Utility Bag use coupon code Tools- www.caliber8.com/product/caliber8-ultimate-utility-bag/
So I had the Milwaukee M18 random orbital sander and decided to purchase the new m18 sheet sander. I tested both on stripping paint from my kitchen cabinets to prep for paint. With both using 80 grit sand paper the sheet sander was way faster at stripping the paint. I figured it was going to be the other way around lol. Was only going to keep one but I don’t know which to keep so guess I’m keeping them both 😂
You are not alone! I am stripping the last bits of paint from trim and my Craftsman 2.0A 1/4 sheet sander is probably twice as fast as my Makita 5” random orbital. Both sanders are using 80 grit 3M pro grade. Go figure!
Great video! I would like to add, if you already have an oscillating tool, you can purchase a sanding attachment to reach those same corners that a sheet sander can fit into. Cheers!
Well I’ll just be darned. I had no idea that plate for the bottom of my sheet sander was to create vacuum holes. So yes, I learned something today. Thanks!
I only have random orbit sander and I use it on bodywork on vehicles coz i only have a small compressor which cannot use DA sander. The good alternative is picking random orbit sander. Its like heaven-sent tool on prepwork. Cutting bodyfiller fast, flat and closest to the body as it could be rather blocking it to size. Also I use them to locate dents on huge panels whicu makes you more productive. Now i want to try finising sander for color sanding. ( getting rid of orange peel. ) My arms grow sore I sand only by hand. Anyway. Clear and concise video. Thank you!
I'm in need of a new sander, so your video is very helpful to me. One thing stood out and that was aligning the holes on the orbital sander. I think I would cut two short dowels to stick into the sander opposite of each other, then slide the matching holes down the dowel. That should be quick, and maximize alignment.
for most of common works and diys what should i buy, i watch most of diys creator using orbital one even for finish? most of time i would like to get paint out of old furniture? or for wall sanding what would u suggest?
Great video! Subscribed! :) Repainting our old doors. Will Sheet sander be enough or should i go for orbital ones? Just need to take off that old paint from the wood.
If your doors have recessed sections with corners, the right angled sheet sander pad can get into those corners better than a round orbital pad. If there are no corners go for the orbital. Have fun painting. Thank you.
This video was so helpful! I'm gonna go with an orbital sander for my DIY project for my dresser and nightstand. What grit should I use to remove the paint and other layers? Should try some type of remover?
You can start with a coarse grit paper and work up to a finer grit. Is your dresser pressed wood. Anything from 40 grit to start on up to 150 to 220 fine grit to smooth it out. As far as removers, soapy water or a heat gun and putty knife are some chemical free options. Nail polish remover or paint thinner are options but the chemicals are harsh.
I have a sheet sander…I am prepping ugly old golden oak cabinets for painting…will it work for what I am doing or should I get an orbital? Thanks for the explanation…great video.
Sheet sanders are better for getting in corners because of the square shaped pads. This is good for cabinets because of all the straight edges and corners inside.
What kind of sander would you recommend me to buy if I'm using it for my ceiling? I'm trying to remove my popcorn ceiling this summer and sand it before I repaint it.
Use a drywall knife or spatula to scrape off the popcorn until the surface is smooth then sand it. Or if you only use a sander to remove the popcorn, use an orbital sander. Start with a coarse grit paper to remove the bulk of the popcorn then use a finer grit as you go in.
Why are you calling a sheet sander a palm sander? I’m trying to understand all the differences and am unsure if I’m missing something. Thank you in advance
I still can't decide. I have an old veneer dresser that I want to refinish. I removed most of the varnish with chemical remover, but now I want to smooth the veneer with more sanding. Which is best?
All sanders leave swirls. If the swirl is very noticeable it could be something in between the sander and the wood, like dust or wood chips, worn out sand paper or sanding technique.
I’m a beginner! Thanks for your video, i want to get a sander, I’m still stumped on which one of the two types to get.. can you recommend? Between the two?
Orbital sanders are more suited for rough sanding work. They are more powerful than sheet sanders. Sheet sanders are good for lighter sanding jobs and there is less risk of over sanding. Sheet sanders are also better for getting into those corners because of the square sheets. .
Depends on if it’s a concave curve(outward) in which case an orbital would do. If the curve is convex(inward) and smaller than the face of the orbital sander you may need another tool like a tailed sanding apprentice.
@@rickferr1546 For the wood garage, start off with a more coarse sand paper like 80 grit then graduate to 150 grit and from that to 220. For the metal door, go really fine with 400 grit, for the tough spots drop down to about 150 grit. a variable speed orbital sander should work.
I am making cricket bat now I am sanding bat with grinder but it makes Mark not giving smooth finishing. So what is best to do my work. Your recommendation is orbital sander????
