Pros and Cons of Low-Temp Solder Paste - Workbench Wednesdays 

Awesome video! I like using bismuth-based, low-temp solder to remove components from boards. This reduces the chances of destroying pads by overheating.

I’m a rank amateur who's a danger to society with a hot air gun. I managed to move 4 SMDs from an Arduino Nano the first time I used one. Low melt solder has been a life saver for me, I can work confidently at lower temperatures when trying to fix my mista… I mean things the manufacturer got wrong.

I do motherboard repair on mainly iPhones. All of this is super important for reballing ic's and running jumpers on torn flexes. Need to master your temp control to do stuff that small! Nice video!!

Interesting, as a home hobbyist I always assumed that low temp solder was lower temp than lead free solder but still higher than leaded solder. I'm glad to know better now.

Very straight forward explanation Thanks for the video!

Very interesting. I have only tried wire solder before.

Wow, that's the first time i heard of bismuth based solder paste. I'm a professional, and at work I only use leaded solder wire, even for small smd components. I prefer it over solder paste, as it doens't really have a shelf life. This definitely changes my opinion concerning lead free alloys, I simply prefer lead.

Could the low temp solder paste work to reattach aluminum terminal studs to the aluminum base on a 3.2v 280ah lifepo4 cell?

You are an excellent instructor. Will b buying this from MG. Thank you.

learned something, so thanks.

Very timely video. Great explanation.

Is there a build video on your reflow oven?

I have an old timy container, jarlike but tiny. Of dolder paste from china yhe entire things in Chinese, can i mix it up with a toothpick to redistribute the flux? Then use it to solder a wire onto a 12v chord

I tried to solder ic with bout 1/8 gap and got bridges the solder didnt melt and it was boiling i used soldering iron and it bridged

what solder station did you used?

Chur bro great video lots of useful tips

you do realise now you have to made a LED chip cookie PCB to have as a prop :D

I've not tried it yet, but the reflow temperature of bismuth-based paste being only slightly higher than my 3D printer's heated bed during ABS prints gives me ideas 🤔 I'm not suggesting the heat bed would do all the work, but it could maybe act like the initial stages of a proper reflow profile, and then a hot air gun could push it over the edge... (I mean a temperature-controlled soldering station hot air tool, not one of the 2kW paint-stripping things, to be clear.) That seems like it'd give more consistent results than the hot air tool alone, especially for things like exposed pads on QFNs or ESP32 modules, and might cause fewer melted connectors and switches 👀 (Obviously something like a hacked toaster oven will give better results than what I describe here, but I'm not at that stage yet! This is an experiment in whether I can get improved results _with equipment I already have_ :))

Hey... this actually is informative... 😳👍

This question may be out of your wheel house, but I am going to ask anyway. I have a Jeep vehicle that has the rear window glass defroster grid. Jeep has a common problem with the electrical connector breaking free of the copper mounting location on either side of the grid. The recommended fix is sort of epoxy that conducts electricity (which doesn't work, mine fell off within an hour after the dealer repaired it), or just replace the glass. You can bet the the connector will come loose on the new window sooner than later. Do you think this low temp solder could be used to make a permanent repair to these defrosters?

I need to solder the "wire" (small tab like thing) back onto my rear window defroster. Would I just put a blob on the defroster, push the tab onto it and then use my heat gun to reflow it?

What paste do I use for Hi power LEDs

Low temp solder is great for sensitive chips. Reflow first with SAC and then finish sensitive stuff with the low temp.

hi super video😍🙂🍻👍

the brittle thing is a huge minus for me, but hmm i'm very much tempted to cancel my order and switch it to the half price bismuth stuff :P i'm building a hot plate soldering plate and it can do 260c.

Why would you put it to 225f or 107c to fix your heat problem when you just stated that it was 280f or 138c melting point Little confused

How does one not move a board when using a soldering hotplate, since the hot plate stays hot for so long after turning the power off?

He left aftomod tech and landed here

Some call it balls some call it granules... It's solder, solder... 😳

is Solder Paste = flux ???

Imagine if gold was common. Our electronics would be so much more reliable.

sodder/solder 🤣🤣🤣

..you are FUNNY!

it's always disappointing to watch these videos. i can't afford one of those high tech black and decker reflow ovens! making the hobby inaccessible!

did you just threw that stuff in your mouth?! lol lol lol

Lead was better. All the crap electronics from 2006 Era failed because of the switch from lead solder.

hello i like contact you about wire glue can give me your email /thank you