*We liked it **Fastly.Cool** so much in the basement, we bought a second one for the main level. The amount of moisture it pulls out of the air is astonishing.*
Wish I’ve found your video sooner. I’ve got the same exact unit and thought this was the issue, so your replacement part being available on Shopee really helps ! Thanks for sharing!
Thanks buddy this was the same fix for mine too. I got my ultrasonic 20mm from amazon. Came in pack of five cost about $13. So a $2.60 piece caused so dilemma. Saved me my $130 humidifier. Had in garage ready to dump it into recycle electronic. Pheeewww...
I didn't have to replace the ultrasonic plate on my Anjou diffuser, all I did was take it apart and wipe it down with alcohol and it started working like new.
Being doing the same thing almost for 10 years now. 😂 Wipe with alcohol and it's good as new. The only thing that broke down during that time was the fan, and that was replaced. Changing the ultrasonic unit isn't a long term 'solution', because this sort of issue keeps happening due to water quality.
Very good video, I have the same problem. I am measuring the voltage on the old mist maker, but am getting O. Would you know if there is supposed to be any voltage at the mist maker, where the two wires are connected to the round white mist maker? I am getting voltage to the circuit board. But do not want to spend money on a new ultrasonic mist maker if the circuit board is shot and not providing current to the mist maker. I tried AC and DC and get 0 amps, volts, 0 anything. Unless when the mist maker is shot it has no current going to it. I cleaned everything else up and have tried getting it going. Thak you in advance.
How is mist increased when putting on higher setting? Is a longer pulse sent to the diaphragm (ie. lower setting, diaphragm is off longer)? Does the droplet size change with the output setting?
I think the mist is not vary because they rely on frequency applied and those frequency is not change. Mist can be adjusted by the air coming from the fan which pushes the mist.
If you have a multimeter, you can measure the output voltage of the terminal. Just turn on the humidifier af adjust the knob then tap the probe on the two terminal. You can easily determine where is the positive and negative
How did you find out it was a 20mm part ? I have a MH-903A - Air Innovations Humidifier ultrasonic one but it has a black right (not rubber ) around it
Ang sa akin po ay pag pindotin ko ang on switch mag beep once lang pero ayaw umandar. Pero kun pindotin ko ang light switch mag ilaw cya pero walang mist.
My daughter has this exact one and it keeps leaking as soon as I turn it on. Any suggestions??? This is the 2nd one to do this and I’m fed up, but my daughter really likes it.
Mine has stopped working too. Fan is ok, led is ok, and even i can see the water vibrating above the piezoelectric atomizer but it is not making mist. Is it still possible that the atomizer is bad? Maybe it is not completely bad, it is working some way but not correctly?
Sir Mera Agaro humidifier switch on krne pr ON nhi ho rha maine voltage check kri voltage aa rhi Hai kya problem ho sakti Hai abi 3 month hoye Hai purchase kre hoye
Sir good day po Same din tayo ng unit kaso ayaw p rin mg mist sa akin. Hindi man lng kumukulo. Kakapalit ko lang bago mist maker Any advice po? Salamat at Godbless
Kung no power po possible sa electronics na ang sira. Pwede niyo po ipacheck sa mga electrician. Or kung kaya niyo po check niyo po baka may natanggal lang na wire
My original intention for this humidifier was to use it for plants that require high moisture levels. After using it in my room, ru-vid.comUgkxtD9aJ2m6GU-X1IChQxjn9l31K1A7Kpwj however, I think that's where it is going to stay in the fall and winter season at least. The increased humidity in my room made the room warmer and more comfortable. I had first ran the humidifier for 4 hours with the timer setting for it. After the first hour, I checked my room and can feel the difference. When the full 4 hours was up, I checked again and noticed that the humidifier was shut off as it is suppose to. The moisture level never seem to get passed 56/57%. I then let it run until all the water is used up, which it wasn't all used up. There are still some left in the base that you are not suppose to add water to. I filled up the water tank all the way again, being careful when removing it from the base. Some left over water may spill out. After putting it back on and setting the unit to auto, I let it operate. It didn't stop running, rather I don't know if it did at any point since I didn't check it regularly, for 24 hours after which the water in the tank ran out. The moisture reading never passed 56/57%, which may be a good thing for me. Being situated right next to my bed, the noise was not very noticeable with the occasional water gurgle from time to time as the unit ran.
Ginamit ko kasi sya kanina umusok naman then i tried ilipat sa kwarto tapos hindi na sya nag i steam . Working naman yung mist and all idk bakot di lang umaabot sa top yung usok bigla
sir tanong ko lang po, nung inON ko po may power naman, pero walang mist, and kahit nung inopen ko and inON walang bubbles like nung sa video nyo.ano po kaya ang problem? tnx and God bless.
For me its a quick fix. Its not even complicated if you followed the procedure. My motive is to help people with same problem. Sorry if I did not meet your expectation
Opo para maihinang sa terminal. Pero kung wala po kayong soldering iron pwede niyo naman po icut nalang yung wire tapos dun niyo nalang pagbuholin. Tapos lagyan nalang po electrical tape
@@DrixWorks 16mm po is sakto lng . ang hndi sumakto e ung wire .1.5-3w ung naorder ko mnipis ang wire . ung tinanggal ko na mistmaker is ung white ay mnipis ung isang wire ay mejo mkpal .tingin nyo po anung (mm)&(hertz) kya ang fit sa humidifier. ko . syangnmn kc ko bbili pa bago .
Oo sir napansin ko rin yan. Actually dalawa kasi yung gamit namin na humidifier. Kinuha ko mist maker nung isa yun triny ko dun sa mahina bumuga. Tapos yun dun na ko nagconclude na mist maker talaga sira
Sir ganyan din po yung humidifier ko, kaso yung sakin umapaw po yung tubig at gumapang sa baba yung tubig hanggang nabasa yung loob habang naka-on. Tapos nag amoy sunog na siya sir. Repairable pa po kaya yun sir?
Drix' Works san po kayo banda sa La Union po? Ayaw po kasi gumana ng humidifier po namin. 😥 bagong bago palang po. wala pang 1 week na nagamit po, 3 days lang nagamit tapos after 1 week po nung ggamitin na namin ayaw naman na po gumana. bglang nagflicker lang ung ilaw nung sinaksak po namin sa extension tas wala na po
Boss paano kong tatlong piraso ung ganyan...kasi nabiyak ma lasi ung tattlo lumalabas tubig sa kakalinis nang kasama ko nabiyak..20mm naman sukat niya sir..puwede kaya yan doon ...or lahit anong klase na ganyan basta 20mm sukat