If you have any questions or messages, please feel free to comment.
I have repaired a Gibson Les Paul Studio.
We did refinishing, side scalloping, fret polishing, and overall adjustment.
The most difficult part was the refinishing. This refinish was neither lacquer nor polyurethane.
It is shellac paint, which does not use a spray gun or compressor.
We painted with French polish, which is one of the most time-consuming and labor-intensive methods.
However, to be precise, it is not a French polish finish paint, but a simple polished and polished? French polish.
At the work meeting stage, we were planning to polish only the top, and to use a thin shellac on the body back and other parts of the body, and finish with French polish.
During the process, we discussed with the customer and chose to polish.
You can see in the video how it is finished with French polish in the middle of the process. Polishing after finishing with French polish.
French polish is very difficult from the point of view of those who have experience in lacquer painting.
It looks like you are just twirling the pad while applying the polish, but to get a mirror finish, you need to know the density of the shellac, the amount of oil, the material of the pad, the drying time, and the repetition of polishing while applying the polish. In total, about 300 coats are applied, 6 hours a day for a week.
I dreamed that I was doing French polish, but in a failed state.
Flat boards and furniture without bumps are very easy to apply.
To be honest, I don't recommend applying shellac to anything other than body tops. The labor and cost are out of proportion.
However, I was fascinated by the unique film of Shellac French Polish.
I think it is because it is not a spray, so surface tension does not work, but the paint surface looks like it is stuck to the wooden surface of the body.
When I shine it in the light, guffaw! Gwah! Gwah! The paint film is called "Paint Film". It's hard to describe with a camera, so I'm not sure if it comes across...
I think this is the kind of surface that can be achieved because of the shellac French polish on the arch top. I think the price is high, but it is worth it.
When I see the finished product, I think I would like to do it again.
I will regret why I took such a request when I start working on it....
The highlight of this video is that I used masking tape instead of a scraper to express the binding in the staining of the body top material.
Perhaps.
Thank you for your request.
Parts and tools used
TONE Power Grip Driver Set PLPGD6
amzn.to/2Q5MrRr
Wera Craftform Diamond Screwdriver Set
amzn.to/3s2RoLu
VESSEL Precision Hex Screwdriver
Set, amzn.to/2O6hFoC
1.27(inch)amzn.to/2X4xBvQ
1.5amzn.to/34KDAZs
Fret Polishing 3M Sponge Polishing
320-600 amzn.to/2YC5c0k
800-1000 amzn.to/2JnIEd9
1200-1500 amzn.to/32iG29c
Metal Polishing also Picard
amzn.to/32Ip7f7
For masking tape, 3M is good. For high frets on guitars, 6mm is recommended.
amzn.to/32H0gZ9
Dremel 4000 rotor. Great torque, but hot! If you can, get a 4000 because it can do a lot of things.
amzn.to/2Kh3NH5
I heard there is a new one called 4300. If you can use the base plate of a StuMac, this might work too.
amzn.to/3712F48
3M body polishing compound, this is enough for a guitar.
amzn.to/34WHuhO
It's good to have a lot of stuff, orange English oil for fingerboard
amzn.to/2Kh4G2n
This cloth is very good. Recommended. Seriously.
amzn.to/2PRUJM8
Website
pedaru.wixsite.com/andybassan...
Twitter
/ andybassguitar
Facebook
/ andybassguitar
Instagram
/ andy_bass_and_guitar
#gibson
#restoration
#asmr
#andy_bass_and_guitar
10 мар 2022
