Remote Braking, Backwards Steering, and More Jeep FC Puzzles

Подписаться 563 тыс.

Просмотров 42 тыс.

50% 1

In this video we tackle more issues on the Jeep FC including a remote braking setup, the backwards steering conundrum, and some really rusty bolts. Theres a few hidden tips and tricks in this one along with some crazy solutions to solve this Jeep FC nightmare of a puzzle!
Ep 1: I'm Gonna Build Your Dream Jeep... Then Give It Away! : • I'm Gonna Build Your D...
Ep 2: The Winning Jeep Is… : • The Winning Jeep Is...
Ep 3: I Bought a Rust Free Jeep FC from Utah… • I Bought a Rust Free J...
Ep 4: The Motor Blew Up on the Scorpion… and Then I Flipped It… • The Motor Blew Up on t...
Ep 5: I Kinda Sorta Bought a Jeep LJ from Alabama… • I Kinda Sorta Bought a...
Ep 6: Florida Jeep FC - Its Free… But Is It Worth The Cost… • Florida Jeep FC - Its ...
Ep 7: Look What I found in the Jeep FC’s Glovebox!… • Look What I found in t...
Ep 8: Possibly the Sketchiest Gantry Crane Ever Built - Jeep FC Build… • Possibly the Sketchies...
Ep 9: Can We Free the Jeep FC? - Jeep FC Build… • Can We Free the Jeep F...
Ep 10: Jeep FC Begins Again!… • Jeep FC Begins Again!
Ep 11: The Jeep FC Motor is Full of Water… • 💧The Jeep FC Motor is ...
Ep 12: The Jeep FC Cab is Sitting Pretty… • The Jeep FC Cab is Sit...
•Ep 13: Remote Braking, Backwards Steering, and More Jeep FC Puzzles… • Remote Braking, Backwa...
Ep 14: Will It Start? Can We Get This Thing Running?… • Will It Start? Can We...
Ep 15: The Jeep FC Gets Rubicon Axles!!… • The Jeep FC Gets Rubic...
Ep 16: Jeep FC Can Finally Steer…Sort Of… • Jeep FC Can Finally St...
Ep 17: The Jeep FC Gets 1 Step Closer!!… • The Jeep FC Gets 1 Ste...
Ep 18: The Jeep FC Leaves the Shop for the FIRST Time!… • The Jeep FC Leaves the...
Ep 19: Jeep FC Mixed with a Little M715… • Jeep FC Mixed with a L...
Ep 20: What is Left To Do On The Jeep FC??… • What is Left To Do On ...
Ep 21: You Thought I Forgot, Didn’t You?… • You Thought I Forgot, ...
Ep 22: This 4WD Selector is DOPE!… • This 4WD Selector is D...
Ep 23: I Need Help With This… • I Need Help With This!!!
Ep 24: 1957 Jeep FC… Will it Grab a GEAR??… • 1957 Jeep FC... Will i...
Ep 25: A Little Pritchett Canyon for the Jeep FC!… • A Little Pritchett Can...
Ep 26: Leg Day for the Jeep FC… • Leg Day for the Jeep FC
Ep 27: The LAST FC Video!… • The LAST FC Video!
Ep 28: Jeep FC HITS THE ROAD - For the First Time!… • JEEP FC HITS THE ROAD ...
Ep 29: Jeep FC Goes OFF ROAD for THE FIRST TIME!!… • Jeep FC Goes OFF ROAD ...
Ep 30: FC Overland Adventure Gets Sketchy Quick!! - DBBBpt1… • FC Overland Adventure ...
Ep 31: The Jeep FC Makes My Wife Giggle - DBBBpt2… • The Jeep FC Makes My W...
Ep 32: He Won a Jeep FC… You Gotta Hear this Call!! - DBBBpt3… • He Won a Jeep FC... Y...
Ep 33: The FC was NOT Built for this… Can it make it?? - DBBBpt4… • The FC was NOT Built f...
Ep 34: The Jeep FC is gone forever!! But we hit a Badge of Honor trail first with the Forward Control Jeep!… • The Jeep FC is gone fo...
Patreon: / bleepinjeep
RU-vid Membership: bit.ly/2wGeSec
All the Details: bleepinjeep.com/giveaway/
If a BleepinJeep video has ever helped you consider returning the favor by:
• Supporting us on Patreon here: / bleepinjeep
• Becoming a Member here on RU-vid: bit.ly/2wGeSec
• See what we recommend on Amazon here: amzn.to/2kc6Syn
• Buying a T-Shirt Here: www.bleepinjeep.com/store
• Or Just leaving a kind comment on FB here: / bleepinjeep
This product is meant for entertainment purposes only. Your mileage may vary. Do not try this at home. Void where prohibited. Some assembly required. For off-road use only. Slippery when wet. Batteries not included. Do not use while operating a motor vehicle, heavy equipment, cherokee XJ, wrangler TJ, wrangler JK, or any Jeep vehicle, especially the newer Fiat ones. How-to videos may be too intense for some viewers and children under 30 years of age. Please remain seated until the 4x4 ride has come to a complete stop. Studies have shown viewing these videos causes increased cancer risks in laboratory test people. I am not a professional, I have no training, I'm not even particularly good at horse whispering. Don't believe everything that you know. Please keep your hands in the vehicle at all times. Do not tap on glass. Do not eat anything that has been on the floor for more than 3 days. Keep your hands to yourself. Not to be taken internally. Reproduction strictly prohibited. Driver does not carry cash. Objects in Bleepinjeep mirrors may be farther than they appear.

Авто/Мото

Опубликовано:

24 янв 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 271

@bleepinjeep 3 года назад

@gwood69 3 года назад

Well if both steering boxes are reversed then you’ll be good lol I think the reverse is being reversed back to normal

@jakubiszyn96 3 года назад

I figured it out! if the pitman arm is facing the steering gearbox input then the 90° needs to have the output at a reverse rotation of the input, but if the pitman arm is facing away from the steering gearbox input, then the 90° gearbox will have to have the input and output rotating the same direction!

@conorshenanigans 3 года назад

Hey why not use a steering box from a mitsubishi fuso or some other medium duty cab over so that it's less complicated

@myconight 3 года назад

Please Leave the Lift, atleast give the parts to the winner... Reverse the reverse, smack it on the butt, and Pedro's your Pappy!

@chrisperks1112 3 года назад

If i where you id put "GIVEAWAY JEEP FC" maybe throw in "ENTER, ENTER, ENTER" or something promote the crap out of it, so alot of people have a chance to win. And than it may even be profitable enough that you may want to it more... Make people happy and make your pockets fat. Clear win for everyone

@larryalexander4833 3 года назад

This is the bleeping jeep I grew to enjoy. Like the builds and info matt

@profitlemon5004 3 года назад

At 19:00 I think the phrase youre looking for is "It cant be tight if its a luquid"

@LoganLovell 3 года назад

Ya beat me to it! One of my favorite things to say along with "the faster you go, the less time there is to screw up!"

@bradstubbings9871 3 года назад

Listening to the beginning music, I thought for sure Uncle Joe from Hee Haw was going to pop out from behind a bail of hay and start playing the Banjo. Lol

@10545555 3 года назад

Look into getting an aluminum triple pass radiator can go with a small size and still getting plenty of cooling because it goes through the radiator 3 times before returning to the engine

@danhambrick6331 3 года назад

Good score on the Rubicon axles.I think the weight of that FC is gonna be need them....

@beau7160 3 года назад

really digging this build. been watching your videos for awhile and have to say enjoy seeing your fabrication work grow and get included over the years. nice work.

@davyleupz 3 года назад

A ball joint press tool has helped me a lot with those axle bushings. I tried to figure out the steering game but my brain started to melt so I just went and got my own cookie. Lol 😂🤘

@bleepinjeep 3 года назад

No cookie for you! 🍪

@StormbornJKU 3 года назад

It’s definitely interesting to see this build coming along. Can’t wait to see you start getting to the body work. Getting rid of all the rust and making it look pretty again!

@jimmccabe801 3 года назад

Great video. Can't wait for the next.

@jakedetrick7720 3 года назад

Gonna be an awesome build for sure! And learning tips and tricks with your videos have saved me a lot thanks for your time and effort to pass on knowledge!

@cmac956 3 года назад

Hi Matt, looks like you have it figured out .its great watching you work .look forward to the next video.

@wesmannpaintball 3 года назад

Awesome engineering! Great video!

@dustytrailscactusron 3 года назад

Looking good! Coming along.

@GoatOffroad 3 года назад

Coming along great Matt!! Love seeing you build stuff. ❤️🐞

@jasontanner5656 3 года назад

Always like your videos. Gives me lots of ideas

@NWJeeping 3 года назад

Looks good Matt i can't wait to see it finished!

@carlstanoyevic3070 3 года назад

I love the look reminds me of my cab over days I’d give my big truck for that. Love it

@chriscook8076 3 года назад

Great job Matt! I like what you've done with brakes. I have a similar conundrum with the Willys.

@wyattoneable 3 года назад

You're kicking butt Matt!

@levidbateman5174 3 года назад

Love where this is going... should turn out great!!

@IndianaTony 3 года назад

FCs are awesome. And weird. There are so many unique challenges with this build.

@johndempsey8643 3 года назад

Matt, impressive solution for the brake master cylinder packaging issue!

@thosegrays1 3 года назад

Another great video! Have always enjoyed your build videos and can use all the tips and tricks! Thanks for all the work you put Into your videos!

@kellyduncan5968 3 года назад

Cant wait to see it finished!

@metaldog7128 3 года назад

Loving it 👍

@travisflores1176 3 года назад

Glad to see olight is expanding more...hahahah hats off to you for supporting them!

@holdthatdown6695 3 года назад

For future reference go to your local Home Depot or hardware store and pick up a Diablo carbide tipped sawzall blade. Same thing happened to me on my XJ leaf spring bolts and it cut through them like butter and I still have the blade and use it regularly.

@DonkeyStomperProducts 3 года назад

You got alot work to do keep it up. Good Job!!

@robertpotts7589 3 года назад

Man that already looks figgin bad ass! Love those sit over steer vehicles. Who ever gets to own that is going to be thrilled. Already a bit jealous.

@kurtmccarthy6733 3 года назад

Right goes Right and Left goes Left !!

@RangeRyan 3 года назад

Well as they say...Turn right to go left. Lol. Love the FC build.❤ Keep up the great work🤘👍

@spyhunter99 2 года назад

brilliant idea for the brake booster

@max28197 3 года назад

And I keep learning with bleepin jeep and litebrite nation. Thumbs up..cant wait to be next week

@trashandtrail 3 года назад

2" lift will work...just needs bigger tires to fill those wheel wells.

@jefferyanderson3524 3 года назад

Cool plan for the brakes!

@connerw25 3 года назад

Just became a patreon, can’t wait to see it finished. Love the drawing apoc designs did! You may be able to do a radiator in the grill where the heater core was and in the tunnel in front of the engine.

@connercurzio3645 3 года назад

That brake booster is an amazing idea, but I would build a "drip tray" underneath it, worst case scenario, a brake fluid leak, could possibly cause a fire, dripping onto a hot engine.

@jeepsterdylan8420 3 года назад

Awesome!!!!!!

@toddrhowardplus4 3 года назад

I used my ball joint press and a map gas torch to get old rubber bushings out. Heat it up and push it right out. Clean the sleeve with a small wire wheel on a drill and popped new prothane bushings right in.

@leonkane8240 3 года назад

Hi, I like the shape of this FC cab over. I have never seen one before & certainly never seen one here in Australia. Great video.

@terryjones5798 3 года назад

About time you made more video's , lol

@fredmonroe6042 3 года назад

Amazing jerryrigging !

@michaelcook3919 3 года назад

I used a ball joint tool to press my new axle bushings in. Kind of hard to get it squared up without an extra hand but works like a charm.

@markeetafarmer541 2 года назад

Good hack for hole saw pilot bits. I got tired of constantly breaking pilot bits, so after deep thought I remembered they sell round bar stock at hardware store. Cut a piece of round bar same length as pilot bit. Determine center and drill or use bit in hole saw to drill pilot hole. Then replace bit with round bar and cut with hole saw. if round bar bends cut a new piece. Heck of a lot cheaper than drill bit. + round bar is softer won't snap like a bit more forgiving

@sivteangkuch6112 3 года назад

This thing is freakkin cool

@Bleepincolt 3 года назад

Brake boosting genius!! 👍👍

@bryankrall8302 3 года назад

This is a hell of a millwalkie tool commercial.

@michaelmalmstein9698 3 года назад

For cooling, you could run 2-3 mini aluminum radiators about 9-10" square with electric fans mounted. Run the radiators one to the other and this would allow you to either stack them or remote mount them. You caps also then ditch the manual fan to free up some power.

@nathanwheeler3645 3 года назад

You could use a ball joint press to get the bushings back into the axles. Makes fairly quick work of it

@2147jarhead 3 года назад

a lot of re-engineering going into this little FC, looking good

@lal5555f 3 года назад

I must have this jeep! haha Steady progress I'm surprised how quickly things are moving along!

@sabinwills7687 3 года назад

Im not much of a JEEP guy (I have A Ranger with a 347 stroker on 36" IROKS, a Explorer on 35's and a built up Samurai) but I enjoy these vids on the FC (would be killer to own one).I did subscribe and will continue to watch. We did own a CJ7 that was on 38's (The wife wanted it) but it got to where we couldnt get in and out of it so she got rid of it and we bought a Challenger (go figure). Great vids. Keep it up.

@kurtmccarthy6733 3 года назад

Loved the Video Matt. Can’t wait to “Win My Dads Jeep FC 170 Refined” by one of the best and experienced Jeep Man !!!!

@albertpobre7101 3 года назад

good video

@Davjd_E 3 года назад

Both directions are correct for the gear box. It just depends on how much fun you want to have when someone else drives it for the first time. LMAO

@yodarudy6155 3 года назад

I use ball joint presses for those bushings

@RR-co4wh 3 года назад

The cut in half Dr pepper can is the tool that makes it all work lol

@stanr3491 3 года назад

Youll need to find the air compressor for those Rubicon lockers, they use a super small amount of psi to activate. Also very hard to find replacements if they fail.

@rickyschultz6357 3 года назад

Loving this build. Your new scooter thing should be called a scooler. Obviously.

@brianhaw9398 3 года назад

Or the Cooter

@jasonlyijnen84 3 года назад

i would mount the radiator like the Camaro's did on a angle going forward from the bottom. make them taller without going taller. get a 3 row at 3/4 should be good effort for a 4.0 with electric fan.

@ypopnun1003 3 года назад

Corvette's did the same. I would turn a full-size Chev 90 degrees should be narrow enough to fit. Mount a remote filler tank.

@ChickenStripsLife 3 года назад

Millwright in a building full of welders, I auto safety squinted every time you pulled the trigger on the welder.

@Fabrication101 3 года назад

Kind of complicated but I like that brake booster solution. Initially I was thinking you need to have that 90 degree steering box turn opposite the direction of the input. But I am thinking you're going to need to turn the pitman arm around to the backside of the shaft which would make it go the wrong direction. SO, I am going with it needs to turn the same direction.

@95jeepers 3 года назад

Ball joint press for the axle side bushings.

@manest69 3 года назад

Another method for bushing removal is to burn the rubber part out with a torch and cut the outer sleeve. It looks like you might have experienced that with the control arm bushings when you were trying to get the bolts out.

@Somebabies_ 3 года назад

The shafts turn opposite in the angle gear box also use a ball joint press for the bushings easiest and safest. Snap on has a pricey one but the cups clip on and don’t flop around like otc

@rgsrails 3 года назад

There was company in Raleigh, NC that made a cooler like yours called a Crazy Cooler.

@timryan1360 3 года назад

Lenox thick metal sawzall blades. Cut through a yota drive shaft at the slip off road on the trail. Cut through moly heims... They are $15 each. Worth every penny.

@kululv 3 года назад

great progress! I would have reinforced the rear body mounts below the floor, to distribute the load more towards the outside of the plates. I'm always concerned about the the remote brake master cylinder set up. Its a single circuit set up. if you have a failure, you lose your brake completely. It really should be a dual set up as well! I have a FC170, my radiator dimensions are H:22.5" x W: 16" x 2.75" thick, which must be a 3 row. The old motor was quite inefficient, so a good aluminum 3 or 4 row will probably do it.

@terraforge_motorsports 3 года назад

Answering your question on steering you have to mount the 90* gear box so that that it has opposing input/output. Since you mounted the Jeep gearbox upside down your steering is going to be backwards.

@Lockitinlow 3 года назад

This thing’s cool! Full cage tying into a rack over a tray?

@verberne123 3 года назад

Just an crazy idea leaf the lift but add bigger tyres, so you can ceep the ground clearance to your frame. I think it will ride fine even on 35's

@Brandonscode 3 года назад

You can use a ballpoint press to take the stuck bolts out of the arms/ mounts without damaging the mounts on the axle.

@darrinrebagliati5365 3 года назад

That's your "Cooler, Cooler!!"

@timetable620 3 года назад

A ball joint press works for the bushings

@Baddecisionsjkur 3 года назад

Also it may be worth doing a twin radiator setup.

@gwood69 3 года назад

Them tekton ratchet wrenches 😍

@ingluv 3 года назад

26:00 get a ball joint press to remove/ install those bushings. "Free rental" at many auto part stores, Just verify that it's in usable shape before you drive all the way home.

@lilhack69ify 3 года назад

Little over engineered on the brake booster. Speedway motors street rod 7" dual diaphragm booster under floor mount With corvette master. Cheaper than just that wilwood pedal assembly alone. I wouldn't want to be in the driver seat if the line blows!

@garymolony8880 3 года назад

Id love to win this but getting it into Australia might be problematic. Love the build process though. Keep up the good work

@jeremyhanna3852 3 года назад

It needs to spin the same way to steer correct rube Goldberg would be proud of that steering concoction

@BenSand 3 года назад

I think the phrase you are looking for is "Can't be tight if it is a liquid"

@Revnahead957 3 года назад

That was a beautiful white XJ!!! at 21:15

@bleepinjeep 3 года назад

Ya it was very clean.

@seniorrider9337 3 года назад

Are you required to use steel lines for all brake lines? A stainless steel braided teflon line like for motorcycles would be easy to run in the cab to go from the MC to the SC. Galfer will make any length and connecting ends you require. Just replaced my rubber brake lines on my bike with Galfer SS lines and wow, big improvement in feel. No more sponginess. This is going to be a cool JEEP.

@guyinthegreencar 3 года назад

I want that front axle for my xj. Can't find those rubicon factory elocker axles in my area.

@nathanbrickles6387 3 года назад

To reinstall the new bushings put them in the freezer for an hour or 2 then when they're good and cold heat the mounts up...the don't need to glow but they do need to be hot...slip frozen bushings into hot hole and maybe give it couple of love taps with a hammer just to make sure its seated

@timfisher77 3 года назад

nice work Mat! It is allways interesting to see how you build things. It would be fun if you spent more time explaining the thought process The "WHY"... Why did you decide on a hydraulically actuated remote brake MC.. Why did you decide to build that crazy elaborate steering setup?....Why do you feel like you need to put the radiator infront of the engine

@16driver16 3 года назад

0" of lift is just fine, you can increase the droop in the suspension still for plenty of travel(longer shocks, long arms, etc)

@jorgezuazo6461 3 года назад

Greetings from Peru

@howardhudson7214 3 года назад

I personally think you need to rethink the steering box. You need something that vertically with pitman arm at 90 degrees. It will make your life a lot easier.

@saltyymannscustoms6989 3 года назад

You wont need to use the opposite direction for the steering junction box. As far that steering box is concerned it will still turn right when you turn right. Since its turned around when you turn right the box if would still be in the stock position would turn left but with this set up will turn right if you turn right

@bleepinjeep 3 года назад

Or will it??

@saltyymannscustoms6989 3 года назад

@@bleepinjeep id like think so but time will tell

@omabluevenice 3 года назад

Learning with BleepingJeep 🤣

@jamesonward5141 3 года назад

I'm sure you've already thought of it, but make sure you can get that tower of a beast out that garage door. 🤔 Or it could be good incentive to get the addition completed 😂

@Baddecisionsjkur 3 года назад

Blue wrench always works on stuck fasteners

@omaolalaidh1289 3 года назад

Gonna have to put a lowering kit on it to get that cone head out that shop door

@patrickburke5606 3 года назад

If I recall the radiator in my 1939 chevy coupe streetrod is real narrow and tall, I believe the dims are Core size 22.5"×17"×2.2" Upper/lower outlet 1.5" / 1.8" Core and Tank: All Aluminum Application engine: CHEVY HOT / STREET ROD 350 V8 1938 automatic And this seems to work in that tight space of these narrow, v shaped hoods, could be worth a try as it looks like you have the height, just not the width. This cools my built 350 decently..keep up the great work

@bleepinjeep 3 года назад

I've got 16x16

@patrickburke5606 3 года назад

@@bleepinjeep Wow that's a tight space to work with, I did find a FC170 radiator 3 row made for a 6 cyl online but its over $600...new of course but can it cool that hot blooded 4.0L, tis the question

@ameyers67 3 года назад

Don't take the lift out. It will work great when I put 40's on it.

@Fix_It_Again_Tony 3 года назад

That's what I am thinking. The tires just aren't big enough yet.

@Somebabies_ 3 года назад

Then your center of gravity is too high “As low as possible as tall as necessary”

@jeremy3541 3 года назад

Hey Matt. What you going to do with the scorpion after blowing up the motor?

@Failprone27 3 года назад

23:53 when you tell her you drive a jeep

@natecarbajal4146 3 года назад

I would so get rid of that mechanical fan and run electric instead, help free up some extra room in that space and most likely be more efficient while opening up way more radiator mounting options.