REPAIRING broken lower door molding garnish 2014 hyundai santa fe 877222W000CA 

Fantastic hack where you used soldering iron mate. Worked well. Thanks for sharing this video 2:06

Thank you for sharing. Now I can fix my moms car

Thanks heaps for the vid. Having just endured the same repair, I'd like to offer viewers a couple of other tips. Before removing, undo the the nuts that hold the big clips, one at either end. The nuts are on the interior side of the door, at the bottom and are plastic coated. You can undo them with your fingers. Easy! If you don't do this and those clips (or rather, the molded mounts they slide into) aren't already broken, they will break and mean more plastic welding for you. At around 2:40 in the video, the guy says 'these one don't need a clip they just push onto the square'. They don't push on! You can see they're supposed to slide on but from opposite directions. This did my head in! But, if you remove the clips like I mentioned above, you can slide them in while it's off the door, then when you push the molding onto the door, the bolts pop through the holes and you can do the nuts up on the interior side. Finally, I've got to say... Hyundai... I know you want a clean look, but there's got to be a better way than this! If you are going to engineer it as a disposable part, don't charge $480 to supply and fit. That's what they wanted in Australia!

Thank you for showing this!

You could use a little bit of Brillo pad mix it in while you're welding

Good job I have same issue but it’s a infinity qx60

Looks just like a 2005 Santa Fe. My additional problem is that the molded holder for the clips (two forward most and both upper and lower of the fourth clip back are completely gone. Do you have a work around for this problem? Hoping your reply is not that the whole panel needs replacement. In any event thanks for the helpful video.

Very nice. Unfortunately, this piece has broken off a couple times for me, due to a high curb in front of my house and it catching on it. Most of the clips are missing and some of those molded anchor spots are missing too.

Thanks brother!

Nice work

Hi can u help me I get all my Clips broke how can I get the Clips please

Does anyone have the part number or link for the clips?, thanks

👍

How do you remove it tho?

Followed your steps and got the molding back in place. First time I ever soldered plastic! It worked great. Thanks.

How do we remove the moulding? Need to fix mine like you did. Appreciated

A very good video (short and without wasted time) that really helped me repair my broken molding for the price of a few new trim clips. Thanks for posting.

Looks like you didn't bother with the square pins that are screwdriver into the door... right?

I fixed my own panel. 👏👏 Thank you for this video.

I tried this but once the clips are in and I try to close the door the clips snap off. Any suggestions?

Nice this video was awesome. really helped me out.

Great video, this helped me with my Tucson's molding. Thanks sir!!!!!

Awesome! I backed into a fence post and it popped my the side trim off of my driver side door tonight. Tried ever which way to slide it back on with no success. Now I know what to do thanks to you.

Thanks for this video. The soldering got me part way there. I then drowned all the broken sockets in epoxy resin. Seems to have done the trick.

Thank you...I was going to slide the trim out and try the trim back in

Rick Case would be proud

Legend… thanks so much

JB weld clear weld works best

I see your doors sag also

Thank you. Fixed mine for the price of a cheap soldering iron rather than paying a body shop a small fortune. ***Those two bottom clips you left in can be removed by opening the door and twisting off the bolts they are attached too. Or with the trim off, you can slide your fingers under and touch the bolt. I noticed your bottom part of the trim was sticking out once reattached so looked until I found that little secret. I tried to smash it on at first before finding this out and it resulted in the bottom part sticking out and me partially breaking those clips. Quick soder fixed it.

Helpful! 👍