Rust-Oleum turbo paint buff and wax! Must watch! 

Nice job. I had never painted a car or body parts in 30 years and at least 25 cars I've owned. This past week I painted my teenage son's Impreza in an open carport on gravel and dirt ground. I figured out what works for my area (western Colorado). I did 5 and 7 light to medium-wet coats on a whole car, over 4 sessions without fail. Apply and let dry for 15 (minimum) to 20 (maximum) minutes between coats and it works fine for the paints I used. You should spray two small test areas with all environmental/time factors the same before the actual project. For example, if you have an area to spray that takes 10 minutes to paint it, wait and warm-up/shake your next can(s) for 5 minutes and start the next coat. That's a total of 15 minutes. I know up to 20 minutes is also good. But 40 minutes was too long because that induced chemical reactions and severe wrinkling. I painted in the same order/pattern each time I sprayed a section. I had zero runs, spray errors, or reaction defects. The original paint condition was below average. No body rust, but 50% of clear coat was gone and hunter green was faded and rock chips galore. Below is the weather, process and paint I used. 1. Up to 3-mph occasional breeze is okay, anything faster or constant is to be avoided. Clear skies, for light, preferred. 20% to 40% humidity. Temperature between 50F and 72F while spraying. Warmed spray cans in hot water in a bucket. Shake them as much as possible. Paints used on sides, nose and rear (3 sections): -- Rust-Oleum Painter's Touch Gloss Navy Blue 2X Paint + Primer: 1 medium-wet coat. -- Rust-Oleum Stops Rust Enamel Gloss Navy Blue: 2 medium-wet coats. -- Rust-Oleum Stops Rust Enamel Crystal Clear coat: 2 light coats + 2 medium-wet coats. I think a 5th coat could be applied with no problems. Paints used on hood, roof and hatchback (1 section): -- Rust-Oleum Painter's Touch Gloss Black 2X Paint + Primer: 2 coats. -- Rust-Oleum Universal Hammered Black: 3 coats (4th coat optional). ***Color dries gloss dark grey with blackish specs, not solid black. 2. Sanded car with 100 and 150 grit dry paper by hand, with a scrubby dish sponge as the pad to fold the paper around. First, I sanded high defect/damaged spots...double their original size. Then I sanded vertically and again horizontally (cross hatched) the whole car. 3. From this point forward you must walk carefully to protect from dirt contamination...do not drag or scuff the ground. Wet the surrounding area to help keep dust out of air. Douse car with hot water and wipe down with rags. Let air dry 30 minutes. Check that all areas are smooth/scuffed well...touch up as needed. Wash with hot water+dish soap and rags/sponge. Rinse well. Dry with microfiber. Air dry 15 minutes. Tape up as necessary. 10 to 15 minutes before paint spraying use a microfiber cloth and lighter fluid or mineral spirits (same thing) to wipe down the section to be painted. Immediately before painting wipe all surface with a tack cloth. As you're spraying move slowly and don't scuff the ground. 4. Even in the open air you will want to use a painting respirator, but at minimum cover nose and mouth with thick damp cloth or N95/N100 face mask. Clear, tight fitting safety eye glasses work best...the larger goggles reflect light and make wet paint difficult to see clearly. I had to go without eye cover and just squinted my eyes when the paint spray was thick, because goggles distorted the light. 5. It will take these paint formulas 3+ hours to dry to firm finger touch so leave it alone for 5 hours. I let it dry 24 hours in the carport and then put it in the Sunlight for 2 more days before driving. At 25 to 30 days I'll polish and wax it. If you want to see pics drop me your email and I'll send you a couple.

I have to say for a rattle can paint job it looks pretty dam good!!! Here are a couple of tips for you. Before you do any bodywork you should wash the vehicle laundry detergent works very well and get edges underneath. You used the green primer that is what we call an e coat primer to seal the metal you should have put a primer surfacer then sanded if you needed to, also get one of those wet sanding sponges so you don't get the finger lines as you sand and put a couple of drops of ivory liquid dish soap in the water it helps with smoother sanding. The biggest thing never ever wax a fresh paint job!!!!!! Wax doesn't make the paint shine buffing makes the HIGH GLOSS the wax is what protects the shine that you just created... get rid of that buffer you need one that you can feather the switch if your afraid of burning the edges put some of the blue painters tape on the edges to help you from burning... Hope this helped you..... Not judging just want to make all cars shiny...Good luck

I do see ripples on the whole hood but due to hand sanding vs. Block, but the results came out awsome regardless. Not bad for budget job.👍

Came out decent but would highly recommend using a sanding block to get the paint flat and even before buffing. Can't wait to see rest of car good job man

That was awesome, talk about a mirror image. I’m doing this to my wife’s Durango. Just picked up 5 Turbo cans of Gloss White. Later this Fall I’m painting my truck with the Turbo Black. You did a great job Sir.

Automotive Spray paint in a can is STILL paint; follow the procedure,(patience included😉) you'll get the results! GREAT JOB!!!!

You should definitely wet sand with the backing pad so you have even and consistent pressure. No circular motions, either.

I cant believe that came out of a spray can. Good job Sir!

Looks fantastic! This is how smart people save $!!! FYI- After you paint the whole van just be careful when pumping gas, it has a tendency to eat through or stain the rustoleum.

That my friend, is a Sweet Heart of a JOB!!! YEAH!!! I am doing my wife's entire Toyota Matrix in Black!

Be carefully bro I bet every paint shop is getting together right now plotting to get ya 🤣 Outstanding job I will be trying this very soon before they catch us out 😂

Very nice job! This is so exciting! I'm picturing my lawn tractor, my tiller, my trailer, and my metal kitchen cabinets all looking like a million bucks! Thank you for posting this video.

This gives me confidence in my car! Awesome job man. Thanks for this.

I just painted the front end of my car with this and was suprised honestly how well it worked BUT now seeing this I am going to go back and paint the whole car and then wetsand and buff it!

I’m in the process in doing two sides to my Mercedes sprinter van I think I’ll start job after watching this great job and awesome video 👍🏼

It came out great, I have an old suburban with awful paint I wanted to hit it with tractor heavy duty Rust-Oleum paint, 😏😏 buffed it'll look factory, now to the second scenario of if black or white color, I like the white with black tints but I also did the black on black look

That’s unbelievable, looks damn good. People will say it’s not as good as Factory. I say that is really good right out of the spray can and a buff. 👍🏼✌🏼🇺🇸

Holy crap that actually looks really good

Looks great! With some elbow grease and effort looks amazing! Obviously he has skill in this stuff but damn looks good especially without a compressor

Looks great for a rattle can paint job! Great for people on a budget or without the equipment to do it the conventional way.

Very nice, it's hard to believe it came out of a spray can thanks for sharing.

My man! You got skillzzzz. I bought that paint for my daughter’s accord. Now you raised the bar what it should look like. Damn. Ps; a guy like you needs a compressor. Please look into Fortress line at Harbor freight. Super quiet, dependable. Had mine awhile. Love it.

Turned out really nice. Meguire's is some awesome stuff. Take it a step further and put some ceramic on it. Turtle Wax makes 1 called Hybrid Solutions. It's one of the best. Only $17 a bottle. Others are $30+ for less.

I'm learning you did an Amazing job. My first time painting with spray paint. This is Awesome really learned alot. Thanks for the Videos...Totally Subscribed 100%%🙂

Can’t beat that look. Nice work. Use a sanding block for the paper next time. Your job will look smoother next time. 🤘

This is AMAZING! so I could do this to my whole car if I wanted to? This is crazy good !

Love it. Been prepping an old trailer. you sold me . I'm ready.

I wish u were my neighbor this way I could do my 96 civic dx coupe, it needs paint bad, you could handle it 4 sure, great video and talent!

Ditch the meguiars compound with the right products you will get that level of shine before the wax coat, also handy trick few drops of dish soap in the water helps when wet sanding

You should be using a rubber block to wet sand. Also should be sanding in an X pattern instead of circular. But you know what? This does look pretty good. Good job man.

Looks really good brother. For what you used you can’t beat the results. Keep it up

I shoot quite a bit of rustoleum, but use gun, hardener, Japan drier, fisheye retardant, a lot of Acetone, , get it thin enough to to flow well, and recoat as recommended. Mine usually is fingernail hard in an hour.

Hey Carnal how does the Paint hold up? Does it flake off or fade ? I want to paint my Camper shell with the same paint... thanks for sharing this video

Great video man, one tip though, NEVER use a brush to wash your car, you're going to eventually scratch the paint or leave scratch marks

Youre a lot better at that than me! I dont trust my hands to sand evenly. I use a foam block or sponge. Some people can use their hands because they can feel it better. Looks great man, Thanks for this video.

My detailer side came out when i saw that brush he was washing with, then i remembered hes sanding anyway lol but use a sanding block(or even a sponge) so your sanding comes out right. And dont do circles do a cross hatch

Amazing finish. Top job fella, I'd be happy with that. 👍

That's impressive 👍. Keep in mind there isn't much UV protectant in spray bomb. It will probably look like a chalk board in 6 months to a year.

Nice rattle can job! The can't wait to see the rest of it when it's finished!

Wow man great job. My project Ford 500 needs something like this and I’m going to try doing this thanks for the inspiration

Wow looks amazing ! Great job ! Now i know what to do . Thanks ! 😊

you know very well polishing tricks, just i think you my used 600 grip sand paper , before 1500 , .. because you got some orange Peel in the corners. but for spray paint job, you own my respect

Good job my friend beautiful!

You did an awesome job

Wow, it looks great! It looks like a mirror.

After the compound you should have used a polish then wax to seal it. Not knocking your work but you should always follow up with a polish after compound. The finish absolutely comes out better.

I always say you can have an amazing paint job with rattle cans if you do the same steps and preparation you would do with a normal paint job.

Should have wet sanded more. Still see orange peel. Really good considering it came from a spray can though. Nice job!

Great results with a rattle can. A palm sander and 600/1500/3000 grit would flatten down that orange peel and bring out more shine.

wet sand with a pad. cross pattern (front to back, then also side to side) no circles.

I have seen body shops do panels like this NEVER look this good for hundreds of dollars....

Not criticizing, just passing along some tips. Be careful when you’re buffing sharp edges or edges of panels. Noticed you had the buffer turned the wrong way on the front side of the hood, always let the buffer roll off of any edges to help reduce the chances of burning through or it catching and messing up your work

Looks good BUT BE WARNED rattle cans have no hardner or uv protection, it will scratch VERY easily and over time fade very badly. Again it looks good for a budget but over time will quickly deminish.

Hell yeah I like it. Looks good. I would’ve done a clear coat. Here in Texas that paint won’t last a year without a good clear coat

How long did you wait after painting til you wet sanded? I just painted my fender and wanted to know its curing time. Thanks for posting this video!

I painted my toolbox with gloss black 50 percent more spray and I had to do it in my backyard in the evening when the nats are out and I got some nats in the paint, can I wet sand the paint before I clear coat it or just leave the imperfections in the paint and clear coat it and wet sand the clear coat.

the result is amazing

Welp, looks like I'm gonna paint my truck now lol

Outstanding job! I LOVE IT!

That came out really good man

Have you tried to swap the cap from one of thse turbo cans to a regular can

Wow that came out great brother! Especially without a clear. I'm going to follow your steps if I mess up vinyl wrapping the hood.

would wet sanding it with a rougher grit sandpaper remove more orange peel. For example he used 2000 grit sand paper and removed some orange peel. Would a rougher grit like 1000-1500 remove almost all of the orange peel?

Lol. That polishing pad is owning a few years to the graveyard

Wait I’m confused I thought this was going to show you how to ping the car, so this is after you use the rust oleum paint can?

Damn, this looks really good. I am planning to paint my whole car with the Turbo paint as well, so I'm just taking tips and tricks to do it

Going to be doing my 2006 Kia Spectra in that black very soon. Hope it turns out like your hood my man. Awesome job, hope you do some more.

You can polish anything to look good. The question is how long does it last? Especially with no clear coat to protect it.

Thank you $10.00 paint job Awesome !!

How long after paint can I buff it???

Wonder how it holds up to any spilled solvents? Gas , brake clean etc. but yeah, for the price you can’t go wrong! 👌

The pad you use to sand is so you dont sand finger grooves into the paint. It will make the paint flatter.

Nice work bro looks really good especially being spray paint

Looks badass, just subscribed

That looks good as hell

Hold up man.. are you wearing crocs while buffing?

Nice effort... Add some soap to your wet sand, it floats the paint off the paper and keeps it from clogging. Paper ain't cheap, this makes it last. And easier to sand. I like dish soap, but your car wash soap will do fine.

Tip..use that same polish on those headlights with that buffer wheel. You will have new shiny headlights. Then put the wax on the headlights to protect them from the sun. Your welcome

Actually for sanding you want to do x patterns especially on black cause the swirls show

Very impressive Nestor 💯 great job maestro 🤑

Isn't the original paint on vehicle dark blue metallic ? Or has my eyes gone

Wow it looks very good. Was this only with the black paint or does it also have a clear coat?

Is this just the turbo can or did you also use clear coat ?

I love it!! Thanks for sharing.

You don't do circular motions when applying wax..it creates swirl

Did you use a clear coat on top or just the black paint

That's whats Up! Great video bro👍👍

Really good job. But without clear coat I’m assuming the paint will start to fade quickly since there is no protection against UV rays. Super great job none the less.

Awesome job! Looks gorgeous!

so how does the paint look after 4 years ?

sanding block? would have made the sanding more uniform.. especially all the orange peel,, probably would have started at 1000 paper then to 1500 but it looks good for coming out of a can though...

I do a lot of wet sanding. And you're gonna get finger marks in the paint. If you do it with your hand like that you should really use a block

How long will that paint last before it start to peel off?

Use a flexible pad with the sandpaper to wet sand for a more uniform job. Finger pressure creates inaccuracies.

Should have used a bit more compound when going to 1400rpm so you're not dry buffing.Looks good for a rattle can though.

Kool it looks really good my question is what is the dry time before sanding with 1500 grit? Bueno sir I'll stand by 4 your answer again awesome work sir RF from Tejas

Looks good

Did you sand the hood before spray painting it ?

How long did you wait ? After you painted the hood before wet sanding ? And is wet sanding the same as what they call colour sanding ? Thanks