S10 V8 Swap: The V6 comes out to make way for the V8!!! 

Love the videos man great content, love to see progress on the s10

Great video

just...unlinkaged...lmao! Nice dude!

I would like to see you do something on wiring using existing harness..like your vids!

For sure will be doing that to mine sooner or later...i had a 6.6l 400sbc crane cammed blazer (see video) was a beast. So will be doing it to my 1988 s10 i'll stick to a 5.7l this time tho haha. Also next time make it yourself easier, pull with a carb plate.

That sawzall was kickin you're ass 🤣

I want to do this to my 96 s10 lol love the damn truck

Take your hoses off on the engine side and then lift radiator out simplify anything you can to save steps n time. Anyway just my opinion man good video

This channel has to be call it "One ratchet and one socket"

"How high will this thing go?" I think thats my question every time I'm pulling an engine

What grade of sand paper are you using with the disc sander? Nice video I’m restoring my pops 83 S10!

Awesome Channel man. But How the hell do you find anything or walk in that garage?!

I love steely look on s10

You should invest in some power tools, I'm just saying lol

Im hearing a lot of breaking benjamin 🤘😁

Good job, Roman. Just a word from an old rodder, not a good idea to stand your hood on the "Points". Rather, if you have to stand it up, stand it on the side (Points facing to the right or left). Just some free advice from someone who has bent a hood or two.

Sad moments today.. went to go check out my 83 s10 and under the door there so much rust my hand went thru the floor. Got told to get rid of it. But I need single cab in my life. LoL..

Does Less to no humidity make working on Rusted metal parts easier?

The 4.3 goes up the driverside as well... fml...

Good taste in music breaking benjamin playing in the background. Great video showing how this is done too

Did u have to change the trasmisson as well or did it bolt on

Like the video how is the wagon coming along

Did you have to change your motor mounts for the sbc

good luck w the motor mounts.

How did you run the gas pump to the carb . I can't get the pump to come on when I switch it on mine is a 95 s10

Did you buy the truck or was it Pre owned??? I’m just wondering how much this would cost roughly???

I’m here because I’m thinking of swapping mine 93 with a Cadillac CTS 3.6 turbo engine lol only because my 93 Engine blew up lol

Wheels look good on there man I would keep them on there this Kevin ordoyne this my mom's phone

First!!! Lol. Love your channel

What trans did you put in the S10 for the swap

wheres link to you putting v8? and what parts you used?

What size are the rims 15 x10 or 15x 8

What starter did you use for the swap

Where did you buy those steelys

What area are you from and how much would you charge for a swap like this?

I bet the distributor seal was leaking oil pretty bad.

How did u pass smog check bro??

I've done a bunch of s10s if you're going to clean every thing to make things easier to get to there's not that many bolts holding the front clip on remove it it's easier to get engine out and back in and if your using shorty headers you can cut the back corners of the fender welds two fold helps with air flow to keep cooler and you can get to collectors easyer

You forgot to mark around the hinge so it will be easier to put on in alignment.

What year is the truck?

My 92 with the tbi 2.8 left much to be desired but at least it was a 5 speed with 3.73 rear gear.

Why would you not strip the block when it was out, if your v8 it

Re-cip saw for a Y pipe? Smoke-wrench.

Dig the steelies

Nice video!! I have a 1985 Chevy s10 with a 2.5l 4 cylinder engine. I’ve been dying to to an engine swap but don’t have all the experience, tools and money to do so (right now) how hard is this? And what transmission did you use with the new engine?

Are you going to put in a 5.3 LS V8 or a regular small block 350 V8

What year is the s10

hood should of come first

How big of a difference is the gas consumption on a v6 vs v8 in an s10?

Lollll the weight of an LS3 is nearly exactly the same as a 4.3 vortec V6. No front spring swap needed.

привет.остался ли впускной коллектор у тебя.я очень долго его ищу

Steelies Hell yeah

HI vendería algunas piezas?

Question how will that work with a 4X4

Like

Hi Roman, Would you or do you know anyone that would be willing to do a 350 TPI swap in my 1987 S10 Blazer, Tahoe, 2.8 V-6 4X4. It is a 62K mile garage kept like new condition survivor. Original two tone blue paint. Looks like it was never sat in, under the hood it looks like it was never put on the road. It needs the swap, its 2.8 is slower than a riding lawn mower and it just won't get out of its own way.

hey man got some new figured you may be interested idk if you remember but I talked to you about my s10 before with the 2.5 and it threw a rod last week!! so I'm now starting my swap! sent a request on fb hoping you'll respond I have a lot of questions hoping you could give me some pointers!

water from the radiator was no bueno

Agrega subtitulos me gustan tus videos

Work smarter not harder

Y'all know if I can use a 5sp v6 trans on a 305 or 350 or Maby a better option would prefer to stay manual

why not ls.

50 dislikes from people who fucked up their engines on the way out

Peal ane strip it when its out, amatures

this video could have included everything , the engine removal , the cleaning , the engine replacement , but that wouldn't get you your RU-vid money would it

Steelies*

Dude my name is Roman too! And I'm buying a 89 s10 soon. Sick vids.. go check out my 636;)

Dont want to read all below me .manual or auto thks