No video :(

Scissor lift will not drive !!

Подписаться 1,3 тыс.

Просмотров 36 тыс.

50% 1

3219 Skyjack scissor lift no drive on the ground.
Besides the pothole (limit switches) check out the one skyjack tries to hide.
This videos is in case your lift has no initial drive from ground but only drives in the air. Like comment subscribe and Share !!

Опубликовано:

22 окт 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 27

@handymanny214 Год назад

Sorry for the audio guys. Anyone who wants to complaint feel free to send over a Mic !!! Hahaha

@mackpickle 8 часов назад

I have a Skyjack III 3226 Scissor Lift having so issues. When I push the lever forward or reverse, the pump starts running lift doesn't move, after about 6 seconds the pitch changes and then after another few seconds the lift finally starts moving. But it doesn't seem to move very fast, and there is almost zero speed control. I have a video of it, I just don't know how to send it. Any help would be greatly appreciated!

@everleon131 3 месяца назад

Thanks for the tip bro

@nicholasweatherman4097 10 месяцев назад

Anybody had one that will do everything, BUT will not go drive forward?

@user-is8dw3nj6c Год назад

I have a Genie 1930 and working to slow forward and backword.

@everleon131 3 месяца назад

Good morning bro im working on a 3226 i replaced ceilonoid batteries are fully charged mail switch is on.. but now it wont start.. any help please

@jeepTJMurdered 4 месяца назад

What about if I adjusted that but then it’s the opposite. Wont slow crawl while in air? Maybe I didn’t adjust properly?

@handymanny214 3 месяца назад

Check the bottom switches also. Manually close them make sure they aren’t stuck

@eduardolinan7582 Год назад

Can you do a video on a genie 1930 that does not run in the air. Thank you

@jeffreyphong8203 Год назад

i have a JLG 1932e3 i had to change the hoses on the wheels, can you make a video on how to bleed the system ?

@robduckworth8828 10 месяцев назад

After you replace the hydraulic hoses on the wheels (the drive hoses), just drive the unit and it will self bleed the system and eliminate air in the drive hoses

@user-bx7kn9wd4t Год назад

Manuel, i have a 3219 scissor lift just like the one on the video and it is fully charge but when i try to drive the Niddle on the control box goes to zero almost like if its shorting out but when i let it go it goes back to fully charge any suggestions?

@handymanny214 Год назад

Yeah you have a short somewhere Double check the batteries You’re loosing all volts to the top when you stroke !

@user-zd2uh1ox6d Год назад

Hey Manuel, i got a jlg35e that keeps blowing the f1 fuse when i press the pedal, have replaced breakers, wires from pedal to control box and the switches in the pedal. Thanks

@user-zd2uh1ox6d Год назад

Wondering if there are any other relays or limit switches to check

@eduardolinan7582 Год назад

Can you please make a video on a skyjack 3219 selenoid clicks. Lift doesn’t nothing. Will appreciate it. Thank you

@DR.P3RKY 6 месяцев назад

Ever find anything? Having that issue right now.

@blaikebroten6379 Год назад

I have a JLG 2032e2 that the platform control wire got cut and I repaired it and the lift still won’t move at all is there something I’m missing?

@handymanny214 Год назад

Those E2 units are simple but old lol I would start to see if I’m getting volts up on top I know those units also had a line contactor down by the base. When those go out you’re left stranded lol try tapping on it. Does the motor engage at all??

@pwilliams2537 5 месяцев назад

I have one of the 3219 sometime it’s not responding With controller after playing with back and Fort then the machine start to move. What could cost that?

@handymanny214 5 месяцев назад

Bad contactor could be a issues

@jessihawkins9116 4 месяца назад

i fixed a bad contactor on a lift once. the pads were all ate up from arcing. I made new pads with 10/90 solder then used a file to make them flat. it still works.