How to set your belt alignment and also how to properly set the belt tension for your Spyder. I say 32 Newtons and I meant 32 HZ (misspeak), and the paper chart shows Ft. Lbs. and it should just be in Lbs.
It worked for us. Had the dealer do the front pully check and they overtightened and slightly misaligned the belt. First time wife had ever complained about a vibration. got the app for my iphone and set it at 33hz avg. Pretty slick, thank you.
2018 F3-L running about 667 Newtons or 150 pounds. I had 23Hz with the App on my iPhone, however it was cool 50 degrees F with the rear tire on the ground. Thank you for your video, Regards.
Update on the Gates Carbon drive app: It does work now with my new I-phone and yes, you can turn off the startup video by going into settings and turning it off on startup! I took three readings this morning to test it. I got the same reading three times and it also gives you the average of the three. What people are doing wrong is they are trying to pluck the belt with their hand or fingers and that does not work! Use the handle of a screw driver or a small hammer and "TAP" the belt lightly to make it twang like a guitar string. Wheel off the ground, spoke turned to the rear and test all three spokes then average the three readings.
Excellent video and very helpful. Thank you for sharing. My 2022 F3T was extremely tight and on the left edge of the driven pulley , disappointing to say the least. The owners manual is lacking meaningful tech information and according to the dealer no shop manual is available from BRP. Thank goodness for your videos.
after checking 2 separate big dealers in my area they don't even measure tension. Not happy as i have red dust on my front pulley at 10k miles. I'm sure my tension was set too high when i had the rear tire replaced. This is super frustrating to hear no one seems to know how to do this properly at a dealer. I will take care of it myself going fwd. Thanks for the vid..
That seems to work the best! Moving the right adjuster affects the belt tension the least since it is farthest away from the belt sprocket. Move them both in unison to adjust belt tension.
I have a 2017 RT Limited SE6 and manual says my belt tension is also 1050N +/- 150N. I was able to screen capture your figures on paper you held up to camera so I could read them. I realize you misspoke a couple of times during recording. I have Apple phone and there is a Carbon Drive App. I appreciate the information you shared on this video. My question is after two years since upload are you still successfully using this app to maintain/check/adjust your belt tension? And how often do you check belt tension? Thank You
Dave, The app worked well and after two years of checking the belt tension it never changed enough to readjust. I traded in my 2018 and I now have a 2021. I also had to get a new phone this year and I changed over to Apple. The android phone worked much better with this app. For some reason I can't get a good reading with my I-phone, it never gives me the same reading. (not even close to one another)
I got a new 2023 F3-s and I noticed that after driving it that the belt was tight against the right side flange in the rear. I jacked up the rear and adjusted the right side adjuster so that the belt was about 3 mm from the flange when spinning the wheel, spinning the wheel by hand both forwards and backwards. I tightened the axle nut to about 120 lb-ft and re-checked. still 3mm. After tightening the nut to 166 lb-ft the belt went back to rubbing on the right side of the flange when turning the wheel. Loosened the nut and adjusted it so the belt was further to the left. As soon as I tongued it to 166 it went back to the right side. What am I doing wrong?
Always with the tire off the ground, bottom of the belt and take the reading midway between the front pully and the rear pully. Use the three spoke method which means turn the rear tire until one of the spokes is horizontal and toward the rear of the Spyder, take a reading and repeat for the other two spokes. There usually is small differences spoke to spoke. Use the average of the three readings.
comment faire si la courroie est mal placée sur la poulie avant ....elle est collee a l exterieur gauche ..faut il aligner le moteur ..et comment faire..merci
You can only use the HZ readout as a reference point as there are no settings for the Spyder belt in the Caron Drive App. Once you take a good reading with the belt at proper tension, belt has to be at room temp and the rear wheel off the ground, then from that point you can always get your belt back to the proper tension.
That’s exactly what I’m looking for. I have a new RT Limited with about 1400 miles on her and she’s at 27-28 Hz right now. Sounds like I need to tighten the belt a bit. I really appreciate what you’ve done. If you’re ever in the Northeast let me know and I’ll set you up with some great rides.
