No video :(

START TO FINISH YZ500 Engine Build 🤯 BRC Racing YZM500 | Steel Frame Yamaha Two Stroke Dirt Bike

Подписаться 26 тыс.

Просмотров 33 тыс.

50% 1

START TO FINISH YZ500 Engine Build 🤯 BRC Racing YZM500 | Steel Frame Yamaha Two Stroke Dirt Bike
Welcome back to Episode 8, where Tony Jeske from Elite Moto factory assembles your badass YZ500 dirt bike engine from start to finish! We're making sure YOUR BRC Racing YZM500 is the wildest steel framed Yamaha two stroke on planet earth...
🔥 ENTER TO WIN OUR YZ500 BUILD HERE: www.mxrevival.com/
🕘CHAPTERS🕘
0:00 Epic matal into, comment giveaways & todays YZ500 engine build topics
3:00 Meet Tony Jeske of Elite Moto Factory - Master Moto Mechanic
8:47 Answering a subscriber's question: What's better in your transmission- ATF or regular oil?
13:18 Damage Report: New VS old YZ250 transmission shafts - heat damage & oil starvation
15:53 Assembling the BRC Racing YZM500 special water pump using the OEM YZ250 parts
20:55 How to assemble a dirt bike transmission - tips, tricks, inspection & explanations
45:58 Tony's first transmission screw up as an early race mechanic - what NOT to do
49:19 How to clean & prep used engine parts any time you need to reuse them (YZ250 donor)
54:16 YZ500 engine assembly - installing cylinder studs, bearing retainers, peening
1:05:58 YZM500 engine assembly - Installing a brand new YZ250 transmission into the YZ500
1:11:23 YZM500 engine assembly - Installing a brand new crankshaft into the YZ500
1:13:15 YZM500 engine assembly - Prepping the YZ500 cases for closure - pins, gaskets, hardware
1:18:13 YZM500 engine assembly - Trans bench test, shift mech., shaft, & counter balancer install
1:22:13 YZM500 engine assembly - Installing the kick start mechanism, spring & gear
1:24:42 YZM500 engine assembly - Correct timing of the YZM500's balance shaft w/ primary gear
1:27:42 YZM500 engine assembly - Clutch basket & Hinson clutch pack assembly
1:30:40 YZM500 engine assembly - Installing the stator plate, flywheel & reed cage
1:31:56 YZM500 engine assembly - How to check piston ring gap to avoid damage & piston install
1:35:33 YZM500 engine assembly - Checking a two stroke's squish band & adj. with base gaskets
1:43:01 YZM500 engine assembly - Cylinder gasket prep - piston ring, and cylinder install
1:47:16 YZM500 engine assembly - Cylinder head o-ring prep, cylinder head install - tips & tricks
1:50:12 YZM500 engine assembly - Iridium spark plug VS standard G-rated - gapping a spark plug
1:51:42 YZM500 engine assembly - Installing the YZM500's special engine decompression valve
1:53:22 YZM500 engine assembly - Completed install and some special final touches by Tony
**mXrevival's YZ500 BUILD - CONTEST DETAILS***
I'm at it again with over 20 MX companies to deliver not only a mega YZ500 dirt bike to one of YOU, but also a ton of MX parts & prizes throughout the entire build series.
Thank you for all the love & support- it's time to seek & destroy!
🔥 ENTER TO WIN OUR YZ500 BUILD HERE: www.mxrevival.com/
🔥TONY JESKE'S ELITE MOTO FACTORY:
-Elite Moto Factory Instagram: elitemotofa...
-Elite Moto Factory Facebook: / elitemotofactory
-Elite Moto Factory Website: jeskemxcustoms.com/
🔥 WATCH OUR YZ500 BUILD UNFOLD BEHIND THE SCENES HERE:
-mXrevival Instagram - / mxrevival
-mXrevival TikTok - www.tiktok.com/@mxrevival?lan...
-mXrevival Facebook - / mxrevivalonline
🔥 TODAY'S GIVEAWAY PRODUCT LINKS:
-DeCal Works Graphics w/ mXrevival Discount: www.mxrevival.com/contact (just let me -know you're ready - I'll get your discount applied)
-ZRT Throttle: www.mxrevival.com/engine-chas...
🔥ZERO RESISTANCE THROTTLE:
-ZRT Instagram: / zrthrottle
-ZRT Facebook: / zrthrottle
-ZRT Website: www.zrthrottle.com/
🔥 ZINC PLATING RESOURCES:
-How To Zinc Plate: • GOODBYE RUST 🔥 ULTIMAT...
-Zinc plating tools you'll need:
www.mxrevival.com/product-pag...
🔥 LERN MORE ABOUT THE INSANE BRC RACING YZM500 ENGINE KIT HERE:
-BRC Racing website: brcracing.ca/yzm-500-my99-21/
-BRC Racing Instagram: / brcracingcanada
🔥 DECAL WORKS:
-DeCal Works bike mats: www.decalmx.com/product/215?s...
-DeCal Works Graphics (with an exclusive mXrevival Discount!!): www.decalmx.com/content/34?so...
-DeCal Works interactive graphics generator: www.decalmx.com/designbrowser...
-DeCal Works Instagram: / decalworks
ANIHLATR YZ500 BUILD & GIVEAWAY CONTEST OPEN TO ALL LEGAL RESIDENTS OF THE UNITED STATES AND CANADA ONLY (exc. QC) - PLEASE SEE OFFICIAL RULES VIA MXREVIVAL.COM FOR MORE INFORMATION
#BRCRACING #YZ500 #YZM500

Опубликовано:

2 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 208

@mxrevival Год назад

*_NEW GIVEAWAYS! Get entered to win your YZ500 & every new video's MX parts giveaways here:_* www.mxrevival.com/enter-to-win-mxrevival-yz500-two-stroke-build ---> *_BEWARE of fake mXrevival pages in the comments using "What'sApp" and a number - there's only ONE real mXrevival_*

@mikebrown41182 Год назад

Uncle T's knowledge is worth is weight in gold. Anyone close by should consider him for their builds, heck even me living overseas will use his service, you only pick and learn from the best. 🤘🏼

@mxrevival Год назад

He is a true OG!

@EliteMotoFactory Год назад

Hello Mike. Uncle Tony here. I greatly appreciate the kind words and tuning in to our “show”. Now that is quite awesome. I’d love the opportunity to help.

@barkeep25 Год назад

Not doing a 500 conversion anytime soon but still learned a ton of solid information on this build to apply to my own yz. That's definitely pro level attention to detail! Makes me wanna go back through my last bottom end and redo some stuff!

@mxrevival Год назад

I’m super glad to hear that! Thank you very much for watching dude

@seanmuskewitz916 Год назад

This is a $1mm plus video. This sort of detail is insane and you cant find this anywhere else. Jeske kills it, and I hope the next generation uses this level of information from MXREVIVAL and Jeske to keep ripping. This is next level real shit, the new version of an encyclopedia. thank you both.

@mxrevival Год назад

Thank you very much Sean! We both appreciate that, and you. It's great feedback for us as well, because Tony and I are cooking up some plans to keep this sort of stuff rolling together

@motofarmer82 Год назад

This is the best engine build video I have seen. I have been rebuilding my own engines for over 20 years and I still learnt new tricks of the trade from this video!

@mxrevival Год назад

Very cool to read that! Thank you for watching, we’re glad to be of some value for you

@EliteMotoFactory Год назад

Stoked you were to learn something!

@motofarmer82 Год назад

@@EliteMotoFactory It's always pleasure to watch how real professionals do their job and learn something new

@RideJBI Год назад

Killer video with so many tips, advice and insight.

@mxrevival Год назад

Thanks my dude!

@AllThingsCycle Год назад

The meticulous nature of your builds are NEXT level

@humpday2267 Год назад

I agree! Charles definitely builds his bikes uniquely clean.

@mxrevival Год назад

@@humpday2267 Appreciate you! It's a team effort for sure!

@mxrevival Год назад

Thank you very much! Blessed to have an amazing crew of guys that help me pull these builds off!

@CNS206 Год назад

Uncle T is the G.O.A.T.! Love that dude! I trust no one else to work on my bikes.

@mxrevival Год назад

TJ is smooth as silk with these engines 🔥

@robertwoods2505 Год назад

I'm glad to see so much detail going in to my BRC YZM500's engine. I learned a lot of stuff that I didn't know. That totally rocked. Cheers to "Chuck" and his family and, of course Tony.

@mxrevival Год назад

Thanks, my dude! And that’s right, you have to reel it in with the law of attraction!!!

@SL4US Год назад

Tony is a really chill guy and knows his stuff

@mxrevival Год назад

Facts! This Saturday new RU-vid drop with Uncle Tony for the new 2023 Gas Gas 500 build

@cnosigamer Год назад

I bet Tony has a lot of experience with honing cuz' as I can see @ 16:56 he actually got a lot of brushes. Any chance you would make a video with him regarding this topic? Not that many videos on RU-vid

@joshhamby6032 Год назад

This is great had me laughing my aruse off ! And man what a transformation of the engine!

@mxrevival Год назад

I’m so glad big J! I hope you had a wonderful Christmas

@chihuahuaverde425 Год назад

I would enjoy hearing more of Tony's story. Very inspiring.

@chihuahuaverde425 Год назад

Charles, can you give us an idea of what the new transmission cost? Nevermind. I added up the parts on RMATV and its about $1,200 :)

@mxrevival Год назад

About $2800… every main shaft, every gear, clip, washer, seal, completer clutch hub, plate, pack, springs, forks and more #SuperFresh

@EliteMotoFactory Год назад

Thank you for that. It’s kind of long. Maybe someday put more out there…

@jeffboyd7780 Год назад

This is a great video. I've raced and built bikes for over 30 years and I still watched every minute of this build. I have the BRC kit on order and will be referring back to this for my build. I would like to know what engine stand he uses and where could I get one like it?

@mxrevival Год назад

That is so rad, Jeff! Really glad to hear you have one of these coming and even more glad we could add some value for you. That stand is made by. Metaltek and I also carry one just like it on our website, built to order. Hit me up with a Contacts link on the website anytime if you have any questions about it, happy to help: www.mxrevival.com/shop-tools

@nunyabizzness5477 Год назад

Greetings Charles and Uncle Tony! I have a few comments and stories I'd like to add, to help viewers of your masterful build, if you don't mind. I put the 2nd mainshaft clip sharp side down. It retains the 4th drive gear, and 3rd never rubs it. The 3rd gear dogs would bottom in the 5th gear holes before 3rd would rub that clip. When I build a trans, I like to have the ends of my clips coincide with a lateral spline on it's shaft. I also put them either 180 (for 2 clips) or 120 degrees (for 3 clips) apart. Balanced, as all things should be. Also, on a lot of 4 strokes, they use the trans shafts as part of the pressurized oiling system. I make damn sure the shaft holes line up with the gear bushing holes. The case reed Zabel 700s use those additional transfer area base studs, as do the 1973 and 1974 Yamaha SC500s, and probably others too. The machine I know best, the Suzuki LT500R, sure could have used them. They are known for blowing base gaskets there. I prefer that the cases come bare myself. I can see some very minor casting imperfections on the reed and transfer areas that I would grind smooth and clean before installing my bearings. It also makes it easier to grind the cases to match the base gasket, and the base gasket to the cylinder. I can attest to the pain in the ass Yamaha shift fork setup. They can be installed without that trick tool, but it sure ain't fun. I saw you put blue loctite on the bearing retainer fasteners, but I didn't see on the pizza cutter (I like that) bolt and shift pawl drum retainer bolts. I've seen them loosen with use without it on a buddy's CR250R. Extremely dangerous, jumped in and out of gears. Ring end gap is EXTREMELY important. Here's a story about what happens when it's too tight. This happened on an Arctic Cat laydown 800 H.O. with a 920 big bore kit. The builder didn't check the ring end gap, and the ring ends butted up against each other during hard, high throttle use. This caused a lot of heat in the piston, and it caused the ring locating pin area to soften, and the pin came out of the piston. The upper ring then rotated to the middle of the exhaust port. Through a combination of exhaust heat blowtorching through that gap and the ring ends catching the exhaust port, the engine seized HARD. This was a prime example of a great build. Extraordinary attention to detail. Most impressive. Whoever wins this will have a damn good rig. Thanks, and everybody keep on wrenchin'! Kyle T

@nicksmithwestaustralianbee5139 Год назад

Such a detailed engine build guys. Hoping to do this build in a year or so, awesome build to follow. Well done

@mxrevival Год назад

Thank you, Johnny!

@albertking7012 Год назад

This episode is right on the money! As you know Charles I'm working on my Yamaha IT's and my 79 I'm going to probably have to be splitting cases. Tony is so smooth at it so he's making me less afraid to dive in unchecked! Got my redwings long ago bro...lol. The 175 won't be as scary as the 500 but she's still gonna throw some roost! Trying to be confident. The attention to detail and the play by play on the motor is quite fascinating to watch, thank you Charles and Tony! As far as BRC well BRAGGING RIGHTS COMPLETE....straight up! The winner of this bike will have them. One last thing, did you know in 87 and 88 Yamaha built like 8 YZM500 liquid cooled works bikes? They even had aluminum frames! Killer bikes. mXrevival is by far the best bike channel on the interwebs...A Bloodsoaked Symphony-Whitechapel. Jam this one if you've never heard it🤘

@mxrevival Год назад

You’ll do a great job, just nuts and bolts at the end of the day! really glad you enjoyed the video, and thank you for the very kind compliment. Great acronym for BRC as well! As for the metal, you know, I’m smashing my face end of the day for blaster while I listen to that killer tune. 🤘🤘🤘

@tylerjamesgillismusic4782 Год назад

Absolutely ❤ this vid I’d love hanging out with you guys haha! It would be Just like my buddies at home. All humor and working on stuff haha. Very informative vid man love the detail on tranny assembly.

@mxrevival Год назад

We’re just a few of the boys! Like all of us!! Thanks Ty!!

@toddginter3111 Год назад

Excellent video Charles very thorough probably one of the best engine assembly videos I have had the pleasure of watching. That bike is going to be sick when it done. Keep up the good work.

@mxrevival Год назад

Huge thanks Todd! we had a good time, and we are one step closer to getting your bike built all the way! Also, I received your emails. I’ll be getting into those and sending your shirt really soon 😎

@toddginter3111 Год назад

@@mxrevival Thanks Charles can't wait to see the next video.

@tonyscott1795 Год назад

Yeah that was long lol😮 but soo good! Thanks To you and Tony! Never seen a full build like that!!! Things a beast! 🤘

@mxrevival Год назад

Thanks for watching dude! I had to get everything that I could!

@DamianosJDM Год назад

At 57:50 u both got it wrong , on most JP makes vehicles the cross bolts are not Phillips or Pozidriv/Supadriv , they are actually JIS Bolts . Most JP vehicles that have been messed with, have ruined cross bolts in. Using the correct JIS driver, feel and grip difference ,is like night and day , u will never strip a bolt again. True JIS driver designation code is B4633 , can be hard to find because its supposed to be"obsolete" from 2008 and is now defined by same designation code as Phillips which is NOT at all the same. JIS drives are built to grip and give maximum torque with perfect fit. Bolts with dimple are always JIS but there are JIS bolts without it. Available in sizes +1 , +2 , +3. True Phillips driver designation code is DIN 5260-PH/ISO 8763-1 and are sometimes sold as JIS by scammers for reason said above .Phillips drives are made to STRIP the head of the bolt ,in order to avoid overtorque , that's their main design, this applies to all PZ/SD and JIS bolts.If a bolt is stuck u are Fcked with a driver like this , even if u use with a manual impact driver. Pozidriv/Supadriv drives are easily recognized through the second bumps in it and notches always in the bolts. Its not interchangeable with other drivers. Mostly used on wood screws. So True JIS is not only interchangeable with Phillips but the BEST choice for JIS AND Phillips screws , u will never look back.

@albertking7012 Год назад

I ended going down the rabbit hole you just explained. I have a couple Yamaha IT175 bikes and like the one I have had since I was a kid and am going through it this winter to resurrect it because it hasn't ran in 30+....I didn't know about this JIS deal when I was a kid and remember being pissed off about my screws back then. Now at 51, getting back into bikes and ended up learning WHY all my screws are stripped out! Lol. That's good stuff you posted up here. I could be wrong but I think a lot of enthusiasts don't know about the "Japanese Industrial Standard" on Japanese bikes. Thanks for putting that up. Maybe you helped out one of our fellow riders. Happy holidays!

@andyroo3022 Год назад

New to the channel. The first thing I notice is how neat and organized all the workshop is. A pleasure to watch and learn from you guys. I also wish Tony all the best with his business venture.

@mxrevival Год назад

Thanks Sandy! We really appreciate you taking the time to watch

@johnny598a Год назад

Awesome love all the technical tricks

@mxrevival Год назад

Thanks Johnny! Easily could have been a 3 hour video too.

@TheHemiphil81 Год назад

Yes,yes,yes .bro I have been waiting to see this jewel completed...

@mxrevival Год назад

I'm pumped, Phil! Huge step in the process!!

@louiscalmet1662 Год назад

Amazing stuff guys Ididn’t even realise I watched a 2 h video it was that fascinating! Loved every detail of it

@mxrevival Год назад

Hey, thank you so much Louis!

@spork929 Год назад

So awesome!!! Love that throttle tube...

@mxrevival Год назад

It’s AMAZING 🔥

@coloradodirtbike5930 Год назад

Super sick and the engraving on cylinder looks rad. Good luck to everyone who entered and happy holidays.

@mxrevival Год назад

Thank you! Hoping your Christmas & new year kick ass 💪

@thatcrazyguyjay Год назад

nice love the build guys this will be an epic bike

@mxrevival Год назад

Thank you dude!

@oweneccles127 Год назад

So excited to see this bad boy

@mxrevival Год назад

Closer every week my man!!

@floydpowers371 Год назад

I just bought an 01 yz426f and a 02 yz250f witch needs rebuilt. Liking your shows.

@leegorgerat4017 Год назад

Amazing builds🤙🏼

@mxrevival Год назад

Appreciate you

@garyguyette9739 Год назад

2 hours is a long time to be on the toilet, great video. Now I need to walk this off😂

@mxrevival Год назад

Hahahaha. When my wife’s leg falls asleep, I’m like- “which one” so I can torture her…

@alexreyes3438 Год назад

Cool Shirts!, BRC - Beer Run Champs

@mxrevival Год назад

Good one!

@jasperracingmotorsports7232 Год назад

Awesome man very good video informative for my 2 kits

@mxrevival Год назад

Ultra pumped to hear that! Thank you for watching 🙌

@jasperracingmotorsports7232 Год назад

@@mxrevival you say giveaways are through comments I try and put my .2 in haha be sure to check me out you do outstanding work my man and Riley’s the man

@jakecroz747 Год назад

This thing is gonna absolutely ripppp!!!

@mxrevival Год назад

Hell yes, Jake!!

@Weidner36 8 месяцев назад

BRZ (Banging ratched zeros)

@trevorcleave72 Год назад

Great video like getting tips from a professional mechanic ✊

@mxrevival Год назад

Me too! I learned a lot. At a glance, it's all "just" nuts and bolts.... then Tony does about 100 little pro-tip type things as he goes that are what separate him as a true professional builder. Great times!

@hedbngr18 Год назад

I had to re-split my 86 ATC250R cases earlier this year to put a washer on the output shaft. Never going to make that mistake again.

@RIPPERTON Год назад

1:35:00 inadequately explained "squish" Squish is where the piston comes to within 0.5mm of the head. This squirts the air fuel mix across the combustion chamber to create turbulence or swirl during spark and combustion for a faster and more complete burn.

@mxrevival Год назад

Nice value add!

@justinmonroe1500 Год назад

Best race cred

@mxrevival Год назад

🔥🔥🔥

@panicrevracing5336 Год назад

Any updates on the aluminum rm250? I’m in the process of building my own 2013 kdx200 hybrid.

@mxrevival Год назад

Sadly my projects take a back seat to my builds that are on a tight timeline for giveaways! But yes, I will finish it, and I do have some parts building up for it to move forward!

@hawkism Год назад

BRAAAAP , RIIIP, CRAAAAAAP!!!!

@mxrevival Год назад

😂📈

@robhubbs6317 Год назад

Man I learned a lot on this video!

@mxrevival Год назад

Hell yeah, that’s so rad 😍🙏

@Bgatz1029 Год назад

Where did you get the guide for the torque spec with loctite color needed. Have a kit on order and this would be useful.

@mxrevival Год назад

That torque spec sheet will come with your new BRC Racing engine 😍

@MOBLEY49 Год назад

Bring real Cajones “BRC”

@mxrevival Год назад

Hahaha good one

@dracula9504 Год назад

BRC stand for Big Riffle Calibers.

@mxrevival Год назад

BANG BANG

@jamessaul9836 Год назад

Featuring the Shaft and his special sauce!

@mxrevival Год назад

😂😂😂💦

@stephenbell4608 Год назад

Just wondering what that product was that you applied to the base gasket? Silicone or gasket bond? I was always told base gaskets go on dry but maybe the silicone? is a good idea around the water jacket. Great bike build👍👍

@mxrevival Год назад

I forget the brand off the top of my head at the moment, but I believe Tony said it was “____ 211” possibly Threebond…

@TheDocrick Год назад

Content killer. jokes great!! Building an 89 RM250 as I type. Thanks for your help!!

@mxrevival Год назад

Haha thanks Doc! Glad you enjoyed. I need to finish our 89 too…. Such a sexy machine.

@keithpeterson6108 Год назад

Could definitely tighten that squish from BRC's recommendation. The .047" would've been more than fine.

@mxrevival Год назад

Good to know! I’m in my squish learning phase 💪

@RP199 Год назад

😍

@wirth315 Год назад

Solid engine build by two trays Tony, and really good video / commentary by Charles to keep it light and fun/funny the entire way. I can't believe I watched the whole thing. I've got full condficence this YZ 500 will prove to be a bullet proof build with such detail taken by each whack of the peen. Motor / gearcase porn at it's finest. :-) If I win this bike, you can be sure it will be F'ing ridden and not showcased.

@edwardrodiguez8946 Год назад

What an amazing build 👏 I can't imagine winning this beast. It would be nice to be the beauty of the beast lol

@mxrevival Год назад

Haha! You just might be, Eddie!

@edwardrodiguez8946 Год назад

@mxrevival I wish lol let's just say I suck at winning any type raffles at least the money is going to a good place....your stuff is awesome 👌

@justinlaute697 Год назад

🔥🤘

@mxrevival Год назад

😎

@mercmanwon 6 месяцев назад

So I’ve been watching 2vintage build motors and I had to come here to undo what I saw.

@doughills8024 Год назад

Aren't you supposed to heat the gear and not the shaft???

@mxrevival Год назад

The shaft, in this case, is the junk part

@adamreno3653 10 месяцев назад

I'd like to see one of these engines in a quad.

@mxrevival 10 месяцев назад

👀👀

@stephencrisson3595 Год назад

Brc big red Cycles

@mxrevival Год назад

😎😎

@tweakit_7 Год назад

Man I really need one on those throttle tubes lol I keep braking clamp on grips and throttle tube hahahaha. Guess I should stay on the bike hahahah

@mxrevival Год назад

😂 "I THREW IT ON THE GROUND!!!" Fingers crossed for you J-Man!

@tweakit_7 Год назад

@@mxrevival haha I've had to by a new set of grips two rides in a row good thing there cheap with my work discount hahaha

@barra245t2 Год назад

Phillips head or posidrive don't fit the screws quite right.jis driver bits are the ones.

@mxrevival Год назад

Soon as I stopped filming, we smashed a number three in that bad boy

@stephencrisson3595 Год назад

I didn't know those new BRC 500 kits ran the one needle style crank bearing on the one side like KTM does KTM uses them that's pretty cool makes for splitting cases a lot easier sometimes you don't need a crankcase splitter with that style bearing little persuasion with a rubber mallet you can pop them cases open sometimes as for the other case have you might still need the crank puller not always though that's pretty cool whoever wins this bike is going to be one happy camper

@mxrevival Год назад

I thought that was pretty slick as well! Tony mentioned to me that was a KTM thing 🙌

@scottydaly7270 Год назад

There’s enough in here to choke a giraffe 😂😂😂😂

@mxrevival Год назад

😂 he died….

@kylenarra3783 Год назад

Busty Ranch Cream Racing I assume

@christopherdemanche8539 Год назад

I hope I win this bike this thing is sick!

@mxrevival Год назад

I hope you do too!

@fredmitchel1236 Год назад

How about applying some man butter to that water pump shaft before pressing

@loganryder2854 Год назад

Is that the new RMZ photo bombing in the background 🧐👀

@mxrevival Год назад

Busted! That’s one of them! I found a 2017 RMX with 12 hours on it at my buddies dealership. Couldn’t pass it up! the 15 we talked about on the phone will be here in a couple weeks 😍

@loganryder2854 Год назад

@@mxrevival guy is over here treating RMZ’s like Pokémon, tryin to catch ‘em all 🤣🤘🏼

@jamesal0 11 месяцев назад

How does a yz250 2t gearbox handle double the torque? They were never great to start with. False neutrals after 12months etc

@mxrevival 11 месяцев назад

No problem so far! I’ve had issues with Suzuki transmissions, but never Yamaha. I’ve heard some guys complain about their gear. But never experienced it myself. Only the shift selector bearing coming apart on the 250, sending ball bearing through the transmiss 🙃

@brapptv44 Год назад

I have one for brc but I better keep it to myself 😂

@mxrevival Год назад

Oh no ya don’t……

@mxrevival Год назад

Inquiring minds need to know

@kylonendres8380 Год назад

Big raunchy chickens

@mxrevival Год назад

They gon’ bite!!

@kylervlogsdotnet69 Год назад

BRC stands for brickedup riding co

@mxrevival Год назад

😂

@someoneyouknow96 Год назад

Why did he heat up the water pump shaft? Wouldn’t that expand the shaft? I would have thought he would have put the heat to the gear expanding the gear allowing the shaft to press out easier.

@michaelwendler5589 Год назад

I was getting ready to post the same thing. He should of heated the gear to expand it and not the shaft.

@mxrevival Год назад

I believe that when you have a steel on steel application like that, heat in general is going to help things "loosen up" and come apart regardless. Like sore muscles in a hot tub - maybe a lame example... There's really no option in this case to heat one or the other without direct heat transfer- unlike an engine case, for example, where you could expand the aluminum case exclusively around a steel bearing race... especially due to being two completely types of metal where one of which expands rapidly while the other doesn't.

@mxrevival Год назад

@@michaelwendler5589 Replied to Dustin.... 👍 Thanks for watching, Mikey!

@barkeep25 Год назад

CHARLES MAN DANG!! My butt went numb watching this long ass video on the shitter!!! Dude even my chick asked me if I was ok? All I told her was I just can't stop watching these 2 men playing with their lubed up shafts and what not...Anywho... I guess she's going to be staying at her moms place for a while soooo...... HOUSE PARTY!!! BYOB!!

@mxrevival Год назад

Hahahahahahahahaha Bring Your Own Boyfriend 😂😂😂 awesome comment, bro. had me rolling

@barkeep25 Год назад

@@mxrevival awesome enough to win a weekly giveaway!?!? Cmon Charles almost gave me cc info to some mx revival imposter scammer!! Knew it was fake when I asked the dumbass about the sick metal that plays in the intro, said it was aluminum......

@mikeguliz Год назад

come on everyone knows BRC stands for Badass Racing Compoments

@mxrevival Год назад

DUH!!!! Good one!

@mxrevival Год назад

Mike! You won a shirt! Just did all my picks & I liked your answer for what "BRC" stands for!! Congrats on another win, dude! Can you please shoot me your shipping info here as well as your *_shirt size?_* www.mxrevival.com/contact *_THANK YOU BRO!_* -Charles // mXrevival (PS I haven't forgotten to check out your channel 😎)

@mikeguliz Год назад

Thanks that’s awesome. I’ll send you my information 🤙

@mikeguliz Год назад

Have a good new year Charles good to hear from you

@fredmitchel1236 Год назад

Man butter: Dupont Krytox grease....

@andreasjonsson8075 Год назад

Minimum squish of 0.58 what? mm or thousands of an inch?

@mxrevival Год назад

You got it, thousandths! Millimeters would be a little over 2 inches 😁 apologies if we made that unclear, been a minute since I watched this one

@andreasjonsson8075 Год назад

@@mxrevival Maybe a dumb question but I know almost nothing about engine builds, so I thoght ill ask. Thanx dude, you've got a mean channel and a beast of a bike too. Cheers from Sweden!!!

@PremixandPedals Год назад

This was an amazing video!!! So very informative and just as important, wildly entertaining!!! I have clicked off of so many videos because they were snooze fests....you two made this video so much fun with all the pens jokes!!! I do kind of feel sorry for your wife if you are like this at home, though!!! Lol!!!

@mxrevival Год назад

Hahahaha thanks Todd! I know how dry and boring. Most videos are in general, and it’s honestly always heavy on my mind making sure things don’t suck. I feel this particular style of video can be pretty plain and slow going so I’m glad uncle Tony and I are able to drop a little bit of cured humor in there to mix it up. My humor is certainly not for everyone, and it is way worse at home, but at least you enjoyed the video 😂

@Sweendawg32 Год назад

Bungholios Racing company. !

@mxrevival Год назад

I NEED T.P.!!!

@Sweendawg32 Год назад

@@mxrevival we supply the sh**tiest of parts !

@chuckfrisoli1170 Год назад

I think he’s a bit confused by newton meters. He kept saying 100Nm. That’s around 70ft/lbs. He should’ve been saying 10Nm for 7 ft/lbs.

@mxrevival Год назад

Definitely a bit distracting having somebody make dick jokes and film you while you try and do something technical as well. Ha ha ha.

@chuckfrisoli1170 Год назад

@@mxrevival lol, I wouldn’t know but I’m sure it distracting. No worries. Hugely informative video. 👊

@EliteMotoFactory Год назад

Hi Chuck. Thank you for pointing that out, but I feel the need to interject. The pee pee jokes aside I was referring to deka n/m which is what my torque wrench is for small fasteners. 100 dnm = 10 nm = 7.4ftlbs. We do appreciate you watching us dingbats.

@chuckfrisoli1170 Год назад

@@EliteMotoFactory ahhh, makes sense now, and I wasn’t trying to come off like an asshole, I hope that’s not how it sounded. This is a great, informative and entertaining video. Your attention to detail is second to none.

@EliteMotoFactory Год назад

Mega a hole Chuck, mega. I’m the doofus that said it all wonky. I do appreciate you saying something and for the compliments. Uncle Tony

@chuckfrisoli1170 Год назад

Bulbous Rod & Crank racing

@mxrevival Год назад

That’s a good one 😂

@user-cl5kx9pp6o 7 месяцев назад

Can I win

@mxrevival 7 месяцев назад

That particular giveaway has ended, but you can check out our new one here! The WORST dirt bike engine we have EVER seen... we had to use a SAW to open this WASTED YZ125! ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-QmBaER4B8b8.html

@ArdenBallard Год назад

BRC…. Beefy Rigid Coc… ehem Crankcase!

@mxrevival Год назад

Hahahaha very fitting humor for this episode

@ArdenBallard Год назад

@@mxrevival that’s what made me think of it hahaha. It’s a phallic episode 😂😂

@doob73 Год назад

ill ride the shit outta this bike if I win it....

@Scaffforlife187 10 месяцев назад

Stands for buttrecoil

@scottdougherty4136 Год назад

B. R. C. - Bring Reinforced Cohones because this thing is gonna rip

@mxrevival Год назад

Hahahahahaha I think this is a winner! Will check all the comments but this is my favorite so far. I will probably spout this off at some point 😂

@mxrevival Год назад

*_YEP!_* You won a shirt for sure! Just did all my picks! Congrats Scott & thanks for the laugh! Can you please shoot me your shipping info here as well as your shirt size? www.mxrevival.com/contact *_THANK YOU BRO!_* -Charles // mXrevival

@user-mf1vj4bb3z 7 месяцев назад

I thought u were turning 250 into 500 your not it's a total new motor

@mxrevival 7 месяцев назад

Yes, completely different engine, built to drop directly into the Yamaha chassis

@jensduhem8904 Год назад

Boy sniffs alot

@mxrevival Год назад

😂😂😂😂

@EliteMotoFactory Год назад

😅😅

@EliteMotoFactory Год назад

YOLO

@msrx08 Год назад

1:32:29 Whoa! Looks like John Holmes had a good time with that cylinder.

@mxrevival Год назад

😂 I had to Google that, and I’m glad I did… #PunchedOut

@Digimanis Год назад

Niiiiiice!!!!!!

@mxrevival Год назад

Going down!!!

@humpday2267 Год назад

Should have put a Hinson basket in there but a new clutch is good too.

@mxrevival Год назад

They’re on backorder! We tried… needed to have an OEM one here due to the tight timeline of the build and giveaway

@ahengineering1461 Год назад

you dont heat the fucking shaft if you need to press it out of something else....

@mxrevival Год назад

Be careful or I'll heat your shaft next! 😂

@EliteMotoFactory Год назад

I’m no engineer, but I do love heat, it’s neat.

@bobbyblenio4571 Год назад

Wow,Tony is an Amazing Mechanic 🔥🦾…& as for You Charley,I Better Win this Bike after Watching this Whole 2 Hour Vid & Putting Up with All the Retarted Sexual Inuendos 🤑…HaHa…Thank you So Much for Posting This ! Looks like I’m gonna Head Up to Idaho & Have Both your Services used for my 06 CR125💥💥🦾🏁👽

@mxrevival Год назад

😂😂🍆 we are both grateful and looking forward to that day!