Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: www.fpvknowitall.com/ultimate...
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: www.fpvknowitall.com/support-me/
---
Ummagawd Crew FB group: groups/ummag...
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Ummagawd 2Fiddy frame
* Ummagawd Store - bit.ly/3oGD48j
* RaceDayQuads - bit.ly/3D3plzZ
* GetFPV - bit.ly/3F8SCuY
* Pyro-Drone - bit.ly/3uttr1m
* NewBeeDrone - bit.ly/3Fdg61W
Ummagawd Aerolite 2004 motor
* Ummagawd Store - bit.ly/3inzsrm
* RaceDayQuads - bit.ly/3Fdo23c
* Pyro-Drone - bit.ly/3uEDEYY
* GetFPV - bit.ly/3F4vq13
iFlight Beast F7 AIO FC
* GetFPV (45A version) - bit.ly/2Y9OwCl
* Pyro-Drone - bit.ly/3yjFWyt
* NewBeeDrone (45A version) - bit.ly/3omOSQE
* Banggood (55A version) - bit.ly/3D2maZo
Foxeer Digisight camera for Shark Byte
* GetFPV - bit.ly/3mjRVX4
* Pyro-Drone - bit.ly/3l2SWTS
HQ T5x3 prop
* Ummagawd Store - bit.ly/3irTbGF
* RaceDayQuads - bit.ly/3D10j4w
* Pyro-Drone - bit.ly/3uwQyrE
* NewBeeDrone - bit.ly/3D3ELEl
Scout HD goggle with built in SharkByte receiver module
* Rotor Riot - bit.ly/3kk11SO
* GetFPV - bit.ly/3B93Wo5
* Pyro-Drone - bit.ly/3B4eVzp
* NewBeeDrone - bit.ly/3D7RPZg
* Banggood - bit.ly/2YgXgGI
Shark Byte RX5.1 receiver module
* Rotor Riot - bit.ly/3mSQKji
* GetFPV - bit.ly/3t8EpII
* NewBeeDrone - bit.ly/3orP8xB
* Banggood - bit.ly/3mUTAo8
Shark Byte TX5S.1 video transmitter
* Rotor Riot - bit.ly/2OxWC2g
* GetFPV - bit.ly/3bcLDmu
* NewBeeDrone - bit.ly/3orOQqv
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
-- TABLE OF CONTENTS --
0:00 - Intro and sample flight
• Caddx Peanut fixes the... - My review of the Caddx Peanut
3:15 - Parts list
5:57 - Assemble the frame bottom plate and arms (the first time)
8:52 - Mount the flight controller (the first time)
12:03 - Solder on the main battery lead
13:31 - Install the motors and solder them to the FC
17:01 - My big mistake: arm screws not accessible when tall standoffs are used
amzn.to/3CYQ2FS - M2 screw assortment (take your pick)
20:36 - Why this SharkByte vTX is a bad choice for the 2Fiddy frame
21:48 - Solder on the receiver
• You can flash this rec... - Full setup guide for Happymodel ExpressLRS receiver
23:54 - Where should we mount the capacitor?
bit.ly/3lvpNzz - FETTEC spike absorber
26:04 - Install the camera in the camera plates
27:16 - Solder on the capacitor
30:15 - Smoke check
31:01 - Finish vTX installation/mounting
32:20 - Betaflight: set up receiver
• Beginner Guide $120 FP... - How to set channel endpoints and channel mapping
35:12 - Betaflight: set up aux modes
• Beginner Guide $120 FP... - How to set up aux modes
36:01 - Betaflight: set up configuration tab
38:36 - Flash ESC's to BlueJay to get bidirectional Dshot working
Bluejay configurator - github.com/mathiasvr/bluejay-...
40:35 - Betaflight: remap motors because FC is not facing forward
43:18 - Betaflight: check motor direction and reverse as needed
43:46 - Betaflight: adjust FC orientation
44:47 - Betaflight: adjust vBat max for use of HV batteries
45:15 - Betaflight: set up SharkByte canvas mode OSD
• Shark Byte HDZero comp... - My SharkByte full setup guide
48:06 - Configure SharkByte vTX and camera
50:06 - Betaflight: configure rates and PIDs
pastebin.com/TATZumW2 - Ummagawd PIDs CLI dump
51:25 - Select and install vTX antenna
53:52 - Finish installing the camera
54:58 - Add retention zip tile to battery lead
55:35 - Install Ummagrip battery pad
56:49 - Final weigh-in. Is it under 250g?!
5 авг 2024
