Swingarm Bearing Removal and Replacement | GSXR 1000 | Partzilla.com

Подписаться 177 тыс.

Просмотров 54 тыс.

50% 1

Your GSXR 1000 swingarm bearing replacement starts with the parts: bit.ly/GSXR-swingarm-bearing-r...
Learn how to replace the swingarm bearings in your Suzuki GSX-R 1000. This is a complex job and it requires several parts and some specialized tools to get this done. We’ll replace the bearings in our swingarm as well as the bearings in our rear cushion lever. Check out both diagrams to get a closer look at the parts:
GSX-R swingarm diagram:
www.partzilla.com/catalog/suz...
GSX-R rear cushion lever diagram:
www.partzilla.com/catalog/suz...
The whole process starts by getting the back wheel off. While you’re at it, this may be a good time to replace the chain and sprockets on your GSXR, and here’s a video to show you how: • How to Change the Chai...
Next, we’ll get on with the GSXR swingarm removal. We’ll show you how to remove the swingarm on your motorcycle and then remove the rear cushion lever. To remove them, you’ll need a couple of special tools:
Hex axle tool:
www.partzilla.com/product/aft...
AND
Spanner nut socket:
www.partzilla.com/product/aft...
Once we get the components off our GSX-R, we’ll get to work replacing the bearings. Removing the bearings generally requires another set of special tools from Suzuki which we’ll show you in the video. However, John will show you a couple of workarounds that will require a little more elbow grease but may get the job done. Once we remove the worn bearings, we’ll replace the bearings in the rear cushion lever first and then take care of the bearing replacement on the swingarm of our motorcycle. Finally, we’ll put everything back together again.
Read how to do this job step by step: www.partzilla.com/blog/suzuki...
VIDEO HIGHLIGHTS:
Removing chain and wheel - 3:35
Disconnecting shock absorber - 4:40
Removing the swingarm - 6:00
Removing swing arm bearings - 7:15
Replacing rear cushion bearings - 11:30
Replacing swing arm bearings - 15:15
Reinstalling swingarm - 16:50
Buy Suzuki motorcycle parts here: www.partzilla.com/parts/search...
Talk to us:
Twitter: / partzilla
Facebook: / partzilla
Instagram: / partzilla
In the video we’re working with a 2007 Suzuki GSX-R1000, but you may have similar steps for your Suzuki motorcycle. If you’re not sure whether these steps apply to your machine, leave a comment and we’ll get back to you.
RELATED CONTENT:
Suzuki GSXR 1000 Brake Bleed:
• How to Bleed Brakes on...
Suzuki GSXR 1000 Won’t Start Troubleshooting
• GSXR 1000 Won’t Start ...

Авто/Мото

Опубликовано:

12 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 73

@OVB_NL 3 года назад

I would class myself as a 'Level 1' DIY enthusiast. With this video, i was able to do this entire job on my 2007 GSX-R 750 and i also had the shock rebuilt and with an appropriate lighter spring. Bought a LOAD of tools including an industrial press (love that thing) for the cushion level bearings...makes thins SO much easier. I have just finished putting the swingarm back together including the lower linkages...SO tight but so glad I have replaced it all. Thanks for the great video content. You aren't available in the UK but please consider expanding overseas and I would have happily purchased all the parts from your site. Thanks again John!

@PartzillaParts 3 года назад

Terrific! Glad the video helped you out! And someday-- maybe Partzilla UK will be a thing!

@emilioplays1852 6 лет назад

Man I just absolutely appreciate your videos. There so great thanks for everything.

@jeanbotha6538 4 года назад

To be honest. I think it's better to pay a professional such as yourself than to go out get all the tools and do it myself.. I did not expect swing arm bearings to be such a task. Thank you for the video.

@keithabrahams 10 месяцев назад

In z I’m z m

@tho-AlQoutbain 5 лет назад

You are the man, I can listen to your voice all day . Keep the good work

@yugol.5812 5 лет назад

I always come here first besides other outlets to educate myself on the hobby I love. Great ViDs!!👍🏼as always.

@unggrabb 5 лет назад

Well done. Just the right amount of explanation and the right speed. This is how you do that. Brilliant

@JesusTorres-qr1gz 4 года назад

Hi guys, outstanding information, very well explicit, organized, presented, easy to understand vocabulary, must kind of you for shearing with us those technical tips, keep up the good work.

@Mrmarginofsafety 2 года назад

Swingarm bearing removal was successfull with a Blind bearing tool using a stout metal rod. Tightened the collet into the bearing and using a stout metal rod from the other side used the collet as the striking surface, drove the bearing out in a minute. I heated the swingarm bearing area before. Used the same method for the cushion bearings as well.

@hughiemg2 4 месяца назад

I had to do the exact same thing. Slide hammer wasnt moving the bearing, and even a puller wasnt working. Tried with a rod from the other side and it was just pushing the collet out - finally heated the area for 5 minutes before hand and that did the trick. Wish I had read your comment earlier!

@prozeza 5 лет назад

Fantastic video, thank you!

@herbertXX 3 года назад

great class, congratulations. I speak here of Brazil!

@williamgrissom4142 4 года назад

You're videos hit the mark thanks

@Sk2PPer 4 года назад

Phone Greek Your videos are great, very much appreciated

@daviandavis8790 3 года назад

Every time I see your channel for something I watch it even if I don't need it.

@slavenleko 5 лет назад

Man you are awesome. I love your videos 😎

@jayb8697 4 года назад

U know ur stuff I wish u were here to work on my gsxr 1000

@MegaRexxTrucks 4 года назад

Good video... I drove my old bearings out with a punch... pretty easy with a heavy hammer.. BUT the center tube that acts as a spacer for the bearings is soft aluminum and gets damaged by the punch. So if you plan on driving them out, you will need a new center tube along with the new bearings. Keep up the great videos! Jeremy

@aarr3193 3 года назад

Was wondering where you are placing the motorcycle jack with out damaging anything.

@Roostabergers 4 года назад

thanks, just what I needed.

@user-hi2zk8fl3k 9 дней назад

Very nice explanation!! You are one of the bests out there. But I would like to know more about how much it costs

@jasonbrown1237 5 лет назад

Done it on a 98 gsxr 600 and my bfh came out ok but it did put up one heck of a fight

@MrWayne-iu4vb 4 года назад

Ive done this a few times putting extended arms on. I chose one time to re use the pivot bearings and swap them over to the new arm instead of just paying $30 for new ones installed.I can tell you I did not have that fancy tool to remove them and walked right into a nightmare. I believe it took about an hour to get them both out by hand... Def buy the tool if they have to be removed lol

@fidelcatsro6948 6 лет назад

This is tough!

@johnthake7401 5 лет назад

Hi I had to do some needle roller bearing on a Honda leaver arm but all the needle rollers had come out so I was left with just the outer part of the bearing so I used a dermal grinder with a grind stone I cut some groove to the casing so then I could force the outer casing to collapse in on itself to get the bearing but used a draw bolt system to put the new needle roller bearing in

@svsouza2921 6 лет назад

Congratulations on your great work, it is a reference of knowledge. Unfortunately in Brazil it is very difficult to have the original parts and these tools special, which makes a procedure like this something unreal. But we do with what we have at hand. If you offer merchandising from you I will buy it in the future. Thanks for the videos.

@PartzillaParts 6 лет назад

www.partzilla.com We ship to Brazil!

@gsxr88 4 года назад

Do all your repairs on this bike only. I have the same bike!!!👌👌👌👍

@FREE_PUREBLOOD333 2 года назад

Major job made to look so easy by this guy. Think I'm gonna get the bearing extractor kit and then go for the threaded bar n washers using sockets. Awesome step by step video.thankyou.

@666alireza 3 года назад

Thanks for this video. What is the name of special tools you are ising here?

@kopov4202 4 года назад

Hello! Can you give a link to the repair kit for the Suzuki GSF 1250 bandit 2007 release ???!

@Spanner04 4 года назад

Great videos! How specifically are you supporting the bike centrally/front?

@PartzillaParts 4 года назад

Strapped into the chalk and then a center lift to raise the back.

@Macnificent78_ 5 лет назад

Do you have the Torque amounts ???do you know how many links do I have to cut off on 520 Conversion kit -1+2 lmk thanks

@Macnificent78_ 5 лет назад

Great video. what kind of grease are you using

@Mr.Winston 5 лет назад

Derwin Smith looks like Yamalube race grease

@jimmcconville624 4 года назад

please link the specific tool that you used to remove the bearings from the swingarm. i have been purchasing tools for 2 weeks and cannot get anything that will grab the bearings and pull them out of the swingarm

@maselbac 3 года назад

Slide hammer didn't work for me. Wasn't enough 'slide' to get the momentum to pull the bearings. I ended up putting the collet in the bearings and using a bar from the other side. Tapped out nice with a club hammer

@nikolaiandersen5054 3 года назад

Is he lifting the bike on the oil sump? Is that durable enough?

@sinnataggen78 6 месяцев назад

I used the rod method, applied a bit of heat carefully, to swingarm metal, and woalla, it almost popped out of itself

@hoosierdad4 4 года назад

Great Video .....Can you Put an Extended Swingarm on my Gsxr 1000 ? haha

@daveyt4802 3 года назад

I should probably do this on my V-strom. Winter project! I bet the dealer would charge over $1000 for this repair.

@ryancameron3681 3 года назад

Perhaps a comment about WHY the swingarm bearings would need to be replaced please John Tally.

@alexer1987 3 года назад

How do you lift the bike without damaging anything underneath

@TiberiusStorm 6 лет назад

Due to all the specialty tools, it might actually be cheaper to pay a shop to do it.

@fidelcatsro6948 6 лет назад

true

@yondaimehokage3343 6 лет назад

nah..i think u wrong there...he show us by using ordinary thing/tool there..also if it me i ll just use adding big washer,bolt n nut..

@dhesleefiesta3124 6 лет назад

Aloha John! can you show us how to fix F1

@PartzillaParts 6 лет назад

Whats the code read?

@websolutions6117 4 года назад

My service manual doesn't say that I have to disconnect the drive chain to take off the swing arm. Is it necessary to remove the drive chain? If I have to remove the chain, that would mean I would have to buy a new master link, right? I don't use clip ons.

@PartzillaParts 4 года назад

Yes, you can use a new rivet link.

@ME262MKI 6 лет назад

I got a problem with the bearings of the monoshock of my bike, one of them was in a pretty bad shape so i needed to replace it, sadly i didnt find the same bearing, so i tried to use a bronze piece to replace it, you think it was a good idea?

@PartzillaParts 6 лет назад

Probably not. What's the bike? I'm sure the bearings are available.

@ME262MKI 6 лет назад

Partzilla its a Honda Tornado 2014

@PartzillaParts 6 лет назад

Unfortunately, we only carry parts for US models. You would have to look locally for the parts.

@ME262MKI 6 лет назад

Partzilla yeah im going try to find that bearing, meanwhile that bronze piece must be enought for now, thanks

@Macnificent78_ 5 лет назад

Where can I find the same Torque measurements for the same part just for a 2007 gsxr 750 I just Recently took my swimg are off i just want to make sure I had the correct ft lbs gear video buy the way

@PartzillaParts 5 лет назад

The service manual will have all the specs.

@Macnificent78_ 5 лет назад

@@PartzillaParts I've looked everywhere would you happen to have a link lmk thanks

@geoffrey9888 2 года назад

Why did you have to grind the chain, by removing the rear wheel and the center nut holding the swing arm will obviously remove the chain.

@Hybrid600 3 года назад

Do you have a link for the bearing removal tool set? What brand is it?

@PartzillaParts 3 года назад

The bearing remover set we used in the video is offered by Suzuki. Here's a link to it: www.partzilla.com/product/suzuki/09921-20240

@Hybrid600 3 года назад

@@PartzillaParts very nice kit.

@Macnificent78_ 5 лет назад

What kind of jack is that

@PartzillaParts 5 лет назад

It's a center platform jack. There are quite a few styles out there.

@hectorsantana7564 3 года назад

That's alot of work right there I can do it I believe but the tools are a whole shit of $

@MrCstone1 2 года назад

Do you have an email? I have a couple of questions.

@PartzillaParts 2 года назад

John is live every Friday afternoon on RU-vid to answer questions via our chat. It's normally at 3PM eastern, but today, 10/1, we're doing it at 2:00 because of a scheduling conflict.

@MrCstone1 2 года назад

@@PartzillaParts I have 2 pictures of swingarm I need to ask about.

@hectorsantana7564 3 года назад

Lol I dont think you'll hear about it lol

@googlelimp9834 Год назад

well im looking at yam but im guessing pretty much the same so thanks very much i just wanted to check, also thanks trying different parts how to remove them when don't have all the kit very very cool thanks