Тёмный

The Best Reason to Buy Seafoam? 

Eliminator Performance
Подписаться 100 тыс.
Просмотров 7 тыс.
50% 1

Check it Out!
Today we'll be doing a "Down & Dirty" carb clean on a Champion 75555i Generator, and we'll be using a special tool to get the job done!
Whether you're using Carb cleaner or rust inhibitor, sometimes the red plastic tube/straw that comes with the can just isn't long enough to reach the area you need it to reach!
Today I'll be showing you another use for the long plastic straw that comes with the Seafoam kit, and we'll be using it to clean the main jet, and emulsion tube on this carburetor!
Buy the long tubes/straws here;
8-Pack Shown in Video: amzn.to/3IwcSu1 (Canada)
Other brands of long straws: amzn.to/45j6MGZ (Canada)
5-10 Pack Shown in Video: amzn.to/42TkEGg (USA)
Other brands of long straws: amzn.to/41WqYeX (USA)
_______________________________________________
If you enjoyed the video, hit LIKE & SUBSCRIBE!
New videos every week!
Get up to 3 Months FREE NordVPN with this sign up link; ref.nordvpn.com/VDyPaQedOsk
Lube-Shuttle: www.lube-shuttle.ca/ (Promo Code ELIMINATOR for 5% OFF)
SOCIAL MEDIA:
/ elmn80r
/ eliminatorperformance
/ elmn80r
/ eliminatorperformance
DONATE:
paypal.me/ELMN80R
Bitcoin: 1NYgPvcvBWuhGRewsLE4Scy1cbzwndh5hZ
2ND CHANNEL:
EP Vlogs: / @eliminatorperformance...
GEAR:
Camera: amzn.to/3MqXvUx
Camcorder: amzn.to/3MJqi8n
Tripod: amzn.to/3BMuy0I
Microphone: amzn.to/3Wq4FNp
Cheap Mic: amzn.to/43gcLKN
Old Headphones: amzn.to/45kl6im
New Headphones: amzn.to/3OpK2PD
Headphones for Music: amzn.to/3olPI2t
Editing Software: amzn.to/3OvpR2W
Photoshop: amzn.to/3OxgS1a
MUSIC:
Intro/Outro Music: Burnt - Jingle Punks

Хобби

Опубликовано:

 

20 май 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 95   
@EliminatorPerformance
@EliminatorPerformance Год назад
8-Pack Shown in Video: amzn.to/3IwcSu1 (Canada) amzn.to/3N01ppf (Backup Link) Other brands of long straws: amzn.to/45j6MGZ (Canada) 5-10 Pack Shown in Video: amzn.to/42TkEGg (USA) Other brands of long straws: amzn.to/41WqYeX (USA)
@EliminatorPerformance
@EliminatorPerformance Год назад
You can ask the old man, we probably remove and ultrasonic clean at least 95% of the carburetors that come into the shop for repairs. The remaining 5% get the main and pilot jets flushed out and they usually start 1st pull, and run smooth as you saw here in the video. It's not ideal, but it gets the job done quick when customers don't want to spend a fortune. And I don't offer any guarantees on these jobs either, because without pulling the carb apart, you can't see what may still be in there. The best thing to do is to keep running fresh fuel through them, and keep them running!
@bigsonslawncare
@bigsonslawncare Год назад
I've often wondered how this works and if it really works glad to see this💯👍🏾
@waynestefinashen239
@waynestefinashen239 Год назад
@@bigsonslawncare It works when properly done i have seen many videos with the down and dirty carb clean where it is good enough but i still hear a slight hunting issue.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Great tip on the long tubes. Thanks!
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@paulmysliborski4832
@paulmysliborski4832 Год назад
I swear by SeaFoam. I have added it to all of my small engines as a general fuel maintenance additive for the last 20 years. Awesome stuff, man!!
@waynestefinashen239
@waynestefinashen239 Год назад
Works great we use it to clean carbon build up in engines, at this time we are using K100S+ for stabilising our fuel but Jake has just set up a contract with another supplier with something that is not available on line and will be posting a video on this in the near future.
@ChubbyButcher
@ChubbyButcher Год назад
​@@waynestefinashen239 Excellent product
@Pete.Ty1
@Pete.Ty1 Год назад
👍👍👍 Thanks. I have just watched 2 of your older videos. Testing a solenoid and testing a key switch. So I know my problem lies elsewhere. 🤔😊😊. Thank you.
@EliminatorPerformance
@EliminatorPerformance Год назад
Good luck Pete!
@martinflanagan2506
@martinflanagan2506 Год назад
Another awesome repair, well done. Thanks .
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@robertmillar9279
@robertmillar9279 Год назад
An excellent informative video! Thank-you.
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@HobbyMotorDK
@HobbyMotorDK Год назад
That's a service you can't get from the dealer - great stuff Jake 👍👍
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@lifes_anadventure3565
@lifes_anadventure3565 5 месяцев назад
Super informative 👍🏻
@jimlem2075
@jimlem2075 Год назад
Thanks for sharing these great tips. I used the Seafoam cleaner to fix my sisters snow blower earlier this year works great.
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching Jim!
@danielrobert7181
@danielrobert7181 Год назад
Good and complete video. Got away with an even cheaper approach to lenghtening the spray tube by joining 2 standard-size tubes with a small piece of tygon fuel line I had laying around. Using heatshrink tubing shouls also work. Regards !
@EliminatorPerformance
@EliminatorPerformance Год назад
Nice fix, gotta do what you have to sometimes to make things work. Thanks for watching!
@PainterD54
@PainterD54 3 месяца назад
If any small engine is going to sit not used for any length of time, you should have 2 oz. of Seafoam in the gas. Then you won't have these kinds of problems. It will keep you carb and fuel system clean and is a good fuel stabilizer.
@LewisMowersandBoats
@LewisMowersandBoats Год назад
Looking great Jake thanks for the tip 👍
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@watermanone7567
@watermanone7567 Год назад
Nice trick, thanks for the video.
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@danielrobert7181
@danielrobert7181 Год назад
Talking about great gunk dissolving products, I use Mercury's (the ouboard manufacturer) Power Tune. Like that Seafoam, it's also advertised as a carbon removal product.Regards !
@EliminatorPerformance
@EliminatorPerformance Год назад
I'll have to try it sometime!
@henrymurawskibigdogrepair
@henrymurawskibigdogrepair Год назад
I to use sea foam to clean my carburetor and it work great great video Jake
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@fierodough
@fierodough Год назад
if you want a real quick and dirty (and very effective in an emergency). start the engine with carb cleaner. (often works best when sprayed right in the plug hole). once the engine starts, quickly snuff the carburetor with the palm of your hand (making an air tight seal). This will create an intense vacuum and force fuel through the jets and unclog them. It's also a good way to remove water accumulated in the carb bowl. Now THAT is quick and dirty.
@waynestefinashen239
@waynestefinashen239 Год назад
Thanks have used that method on a few machines but it really does not stop the issue of ethanol and debris in the carb bowl.
@Goomer
@Goomer Год назад
Good tips
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@waynestefinashen239
@waynestefinashen239 Год назад
To all of Jakes viewers i need your help to join in watching Top Conkers Live stream next Saturday at 2 pm EST. He normally has 35 watching and it would be nice to get 250 watching nest week since he has been thinking about quitting the lives. This would surprise him and maybe keep him going!
@michaelotoole1807
@michaelotoole1807 Год назад
i always use some seafoam and marvel mystery oil in my gas. give a little more in snowblower beginning of season. always good to go.
@EliminatorPerformance
@EliminatorPerformance Год назад
Thanks for watching!
@Samlol23_drrich
@Samlol23_drrich Год назад
I prefer A foam and B foam. Thanks for this video. I always wished I had a longer tube.......
@EliminatorPerformance
@EliminatorPerformance Год назад
Yes the tubes are what make the difference, as I mentioned, you can use any product you'd like. Thanks for watching!
@garny3766
@garny3766 Год назад
Hopefully it’s good. I like to use milk house heaters or heat guns to load theses gennys. If the low speed jet passages aren’t fully clean it will show up when you use eco mode then turn on load.
@EliminatorPerformance
@EliminatorPerformance Год назад
Yes heavy load, we were thinking of getting a heater like James Condon uses to test his. Thanks for watching!
@philliphall5198
@philliphall5198 Год назад
I’m still a old hard headed B12 mechanic and it’s great, tea seaform is ok but twice the price and half as good
@EliminatorPerformance
@EliminatorPerformance Год назад
I'll have to try it out, thanks for watching!
@donvoll2580
@donvoll2580 Год назад
Good day Jake Interesting ! I might have to try that sometime. Thanks Long wk end , R U & the Ford going out?
@EliminatorPerformance
@EliminatorPerformance Год назад
Yes just for a little cruise, she's running good and just got her tuned up. Filmed a little update video that I'll be uploading soon. Thanks for watching Don!
@DIYVariety
@DIYVariety Год назад
Well buddy, you used everything but the horses hoof on that machine lol
@Samlol23_drrich
@Samlol23_drrich Год назад
When it does not start he lets the horse give it a kick and that usually works
@DIYVariety
@DIYVariety Год назад
@@Samlol23_drrich Lol what ever works right lol
@EliminatorPerformance
@EliminatorPerformance Год назад
And she starts 1st pull and runs smooth!
@waynestefinashen239
@waynestefinashen239 Год назад
@@DIYVariety I know a guy that hits everything with a hammer and thinks that will solve the issue lol
@DIYVariety
@DIYVariety Год назад
@@waynestefinashen239 Lol it only works if its wraped in a rag lol
@kenhilson786
@kenhilson786 Год назад
Probably could fab a plug for the idle air intake
@EliminatorPerformance
@EliminatorPerformance Год назад
Yea so the seafoam would be forced elsewhere, I like that idea and will give it a try next time I'm doing a quick clean. Thanks Ken!
@kenhilson786
@kenhilson786 Год назад
Instead of regular pour type seafoam I mix 50 ml isopropyl alcohol, 100 ml naphtha fuel and 200 ml diesel.
@EliminatorPerformance
@EliminatorPerformance Год назад
I'll have to try that sometime, thanks for watching!
@kenhilson786
@kenhilson786 Год назад
@Eliminator Performance got that idea from internet where a guy analyzed the msds? sheet
@SevenSixTwo2012
@SevenSixTwo2012 Год назад
Since this is an inverter generator, it should auto-regulate the hertz output.
@EliminatorPerformance
@EliminatorPerformance Год назад
Yea I noticed the voltage fluctuating but the hz were stable right on 60, thanks for watching!
@sweetlou5902
@sweetlou5902 Год назад
Nope, I just drop the bowl, spray up, replace bowl. If it runs great, if not then it needs a complete clean, unless it's got the plastic idle circuit jet.
@EliminatorPerformance
@EliminatorPerformance Год назад
The issue with dropping the bowl when a carb is vertical like this, is sometimes it's difficult to reseat a new (or the original) bowl gasket. Usually why I would prefer this method, or else I'll just take it off and ultrasonic clean jt. Thanks for watching!
@sweetlou5902
@sweetlou5902 Год назад
@Eliminator Performance valid point Jake, but only had that issue once and a wee bit of silicone grease held the gasket in place so I wouldn't crimp it with the bowl... also you could always turn the item on its side for a second ha ha , us old men think we know it all, cause we're all married and have to think on our feet. Love your videos!
@sweetlou5902
@sweetlou5902 Год назад
@@EliminatorPerformance I also save all those red straws, I took 4 once and used some small shrink tube to butt join them into a massive tube for work on my dodge ram... resourceful
@swetybearpaladin
@swetybearpaladin Год назад
0:16 I tried your vid on the mower that starts n dies...cleared the fuel tank, cleaned the carb, replaced the carb n still it dies after mowing a few feet. Any suggestions?
@EliminatorPerformance
@EliminatorPerformance Год назад
Check the gas cap vent? Loosen it off, and if it improves, then it's not venting properly. If nothing different happens, then you may need to disassemble and clean it.
@waynestefinashen239
@waynestefinashen239 Год назад
Well was it the gas cap?
@swetybearpaladin
@swetybearpaladin Год назад
Wasn't the gas cap, replaced the carb, still won't run. It's twin cylinder, so I ran a test disconnecting one plug at a time. Ran better when left disconnected. Checking valve lash now.
@kenhilson786
@kenhilson786 Год назад
Lol. 8 pack cdn currently unavailable. Bought up by the video viewers no doubt.
@EliminatorPerformance
@EliminatorPerformance Год назад
Yea there's been a few packs sold by the looks of it, hopefully they restock. This 8 pack will literally last me years lol I cut one into 3 it's more than enough for what I'm using it for!
@jerryschneider145
@jerryschneider145 Год назад
Tell that customer you will not work on it. I fix that by taking the carb off (I know it is a pain in the butt) and soaking it in my ultrasonic cleaner filled with carb cleaner, and sometimes that does not work.
@waynestefinashen239
@waynestefinashen239 Год назад
Generator runs fine now (tested 4 times cold starts 1st pull on choke and no surging off choke) after Jake did this trick and not only did it save us a lot of aggravation it saved the customer money. Like you said sometimes even ultrasonic cleaning does not solve the issue and we did not want to get involved with the hassle of removing this carb to clean it and then maybe have to remove it again. Rest assured this job not only cleaned out the main jet but also cleared all the debris from the carb bowl and with our fresh 91 Octane no ethanol fuel and k100S+ stabilizer the customer will not have any issues.
@EliminatorPerformance
@EliminatorPerformance Год назад
I fix just about anything my customers bring me, and if I don't have to take something completely apart it's a bonus. Again, we only do these "down and dirty" carb cleans when the customer specifically asks for it.
@jerryschneider145
@jerryschneider145 Год назад
@@EliminatorPerformance You are a good man.
@alveus8205
@alveus8205 Год назад
I can tell it was painful for you to do the down and dirty carb clean. I agree with you that a proper cleaning is way better, but also understand the customer’s desire to save money. Is it possible to snake a little wire down the emulsion tube/jet from inside the carb throat to clear any blockage?
@EliminatorPerformance
@EliminatorPerformance Год назад
Yes I bet you could do that, but blasting some type of cleaner at least it'll soften up the debris. At least it runs and the customer saved some money. But yes, a full carb removal, disassembly and cleaning with rebuild kit is always the best.
@alveus8205
@alveus8205 Год назад
@@EliminatorPerformance agreed. Cheers from just up the QEW in Hamilton
@philliphall5198
@philliphall5198 Год назад
It’s a disgrace to ask a mechanic to halfass fix it and they talk trash about you later I just tell them I don’t do halfass work , Bye 👋
@philliphall5198
@philliphall5198 Год назад
Plus it takes longer to halfass it with seafoam and it’s a dam joke
@robertlee4172
@robertlee4172 Год назад
I'm kinda disappointed you didn't use SeaFoam the traditional way. Sprayed into the air intake, then heat soaking for an hour. I get that the idea was to get the motor up and running, cheap and easy. But if the client is charged for the shop materials (1 can of SeaFoam spray), then wouldn't it be a greater benefit for the generator, to use more of the product during the final stages of the repair? Part of the winter storage prep for my lawn mower and riding mower, is to give it a few squirts of carb cleaner.
@EliminatorPerformance
@EliminatorPerformance Год назад
I used like 1/8th of a can here, not much at all to be honest. I just wanted to use it to blast out the main jet, not so much to get the carbon out of the engine. Thanks for watching!
@waynestefinashen239
@waynestefinashen239 Год назад
Robert we were not try to remove carbon deposits from the engine which is traditionally what you do with Seafoam it was using it along with carb cleaner to remove s piece of debris or ethanol gum from the main jet. Jake did an excellent video of storage but the best is run it out of fuel add some alkylate ethanol free canned fuel that lasts two years run it again then fog the cylinder or pull the plug and spray the cylinder with small engine storage spray wnen the piston is at the bottom of the stroke
@robertlee4172
@robertlee4172 Год назад
@@waynestefinashen239 Yes, I understood this. That's what was stated in my original post. The point I'm trying to make is, why not use the rest of the can of product, to clean out gum, once the initial problem is solved. The customer is being charged anyway.
@waynestefinashen239
@waynestefinashen239 Год назад
@@robertlee4172 Got it sorry for the misinterpretation, and yes the fogging of the engine could have been done with a slight cost increase since we would have used more of the Seafoam.
@robertlee4172
@robertlee4172 Год назад
@@waynestefinashen239 Billable hours are billable hours. Which is to say...$$$$$$. If the customer initially asks for a cheap repair, once the first task is completed, you'd have an opportunity for an upsell. All it takes is a phone call. A win win, for both, customer and your accounts receivable.
@dontblameme6328
@dontblameme6328 Год назад
That's not a generator. It's a kids toy.
@EliminatorPerformance
@EliminatorPerformance Год назад
Just a little fella 😉 thanks for watching!
@waynestefinashen239
@waynestefinashen239 Год назад
And an expensive one at that!
@waynestefinashen239
@waynestefinashen239 Год назад
Plus it will keep your furnace running when it is 20 below and there is no power but i would not buy one but would go with the natural gas generators hooked directly into the power supply of the house.
@davidpawson7393
@davidpawson7393 Год назад
Somewhere in low Earth orbit there's a Tecumseh emulsion tube and a needle seat or so a friend told me coughImfullofitcough.
@kenbaker6177
@kenbaker6177 Год назад
Why wouldn't you just remove the bowl in place and remove the main jet blow it out put it back together I think that would take less time than putting the can together to blow through the main jet from inside the carburetor throat
@waynestefinashen239
@waynestefinashen239 Год назад
If you ever tried that and got lucky enough not to drop the carb bowl gasket where you had to get it back on without twisting it you would know why we did it this way. That method you describe is only perfect if you know you will not lose or need to replace the bowl gasket which is always an uncertainty. If it works out ok it is great but if it does not work out it can be a disaster and take up more time than removing the entire carb. The method Jake showed in the video is an alternative that works using a SeaFoam straw, basically the point of the video. And as they said in that tv show NOW YOU KNOW THE REST OF THE STORY. We appreciate the comment and thought but that is the reason we do not do it that way.
@philliphall5198
@philliphall5198 Год назад
It’s best not do a halfass carb job because they will talk trash about you later, 57 years of mechanic work and I know better Fix it right and take a loss or it’s no period
Далее
How does a Carburetor Work?
23:59
Просмотров 689 тыс.
TOP 3 WAYS TO USE SEAFOAM!!! (That You Might Not Know)
12:04
вернуть Врискаса 📗 | WICSUR #shorts
00:54
would you eat this? #shorts
00:23
Просмотров 1,5 млн
Seafoam--can't believe what it did to my engine!!
10:12
Generator Storage [With or Without Gas?]
7:26
Просмотров 30 тыс.
Did Seafoam Ruin My Car?
10:42
Просмотров 1,4 млн
Small Engine Repair - Basic Tools
19:35
Просмотров 66 тыс.
Stop Your Engine Surging! (Easy DIY Tutorial!)
11:53
Просмотров 237 тыс.
How to Clean a Honda GX Carburetor
17:15
Просмотров 244 тыс.
Weed Trimmers - Don't Rebuild The Carb!
25:47
Просмотров 184 тыс.
How to Run Seafoam Through Your Lawnmower
9:27
Просмотров 220 тыс.
WORLD'S SHORTEST WOMAN
0:58
Просмотров 80 млн
Проверил, как вам?
1:00
Просмотров 15 млн