Titan Wall Mounted Pulley Tower V3 (short version) Unboxing & Assembly 

Enjoyed the video. Considering one of these for my gym, so I'll have to see how it turns out for you when you start using it.

It’s people like you that we need more of! Appreciate the video, thank you so much for taking your time to show us how it’s done!

Thanks for the review! Strongly considering getting this so I appreciate the honesty about the pulleys. Subbed!

Thank you for the video. It's much appreciated. Comments / questions on the pulleys. What prompted you to want to lubricate the bearings? Is it listed in the instructions? I am not an expert in bearings or gym equipment, but here a couple disorganized thoughts. Some bearings are packed with grease and use a sealed race. In general these bearings are not meant to be serviceable. They do not free spin for long periods of time because of the drag created by the viscosity of the grease. However they are very smooth and would seem most appropriate for this application. There are other bearings that require oil or a dry lubricant. I don't think that is optimal for this application. I like how you sorted the bearings out so we could see them. It looked like they are using whatever bearings they can get their hands on, most likely because of supply constraints. Typically you would design the machine to use the same bearing in every pulley to keep costs down. Can you tell if any of the bearings were greased? It didn't seem so. If I buy this unit, I might just order sealed bearings and swap them all out when I install the machine. Any chance you can tell us what size the bearings are? Thanks again for the review. It's very helpful. I'll share it when appropriate.

Thanks for a great review! Like most garage gym owners, I'm limited for space. I have a heating duct running alongside the stud where I would mount this unit. So, no clearance issues for the 25" required at the base but I'm very limited for space at the top of the unit. The very top of the unit looks to be shaped a bit like a "T". How wide is that at the widest point?

Great video! Definitely helped me with assembly for mine. How did you mount it onto the wall? I don't think mine came with wall mounting screws and washers.

I'm not sure if this is standard now, but I just got the short v3 and all 13 pulleys were of the all metal design (inner part, outer is still plastic) and spinned very freely. I did have to sand down one of the plastic end caps which was bowed out and preventing one from spinning.

Very helpful video! Did you make a video showing how you installed it in the wall? I am thinking of getting it for my garage gym but I am worried about the lower mounting bracket as I have tall baseboards so it might not fit, would it be sufficient to just mount it with the upper mounting bracket? Thanks

What did you do with th number 6 bolts?? i can see them on thr ground after assembled! I cannot figure out where they go

lol, the whole reason I watched this was to see how you mounted it to the wall. Guess I missed the best part.

Is this pretty good for lower-body exercises? I’m wondering if I can pull my bench up to it and do leg extensions or hamstring curls. Thanks!

I have a question. Can you bench comfortably or squat on the side the Pulley tower V3 is stationed? I want to set one up on each side potentially but don't want to loose my ability to use bench on that side of the rack.

Hey Greg. When you get a chance, would you mind replying with a link to your video where you run the cables? (Can’t seem to find it). The link never showed up for me while watching this video. Put together my tall V3 and lubed the pulleys yesterday. Running the cables today, hopefully. Thank you!

As an ex-Rollerblade engineer, a metal shield is not better than a metal shield on the bearing. And if you want a fairer spin, hold the pulley vertically as it will be mounted. Good review thanks,.

Thinking about getting this for my home gym but is it as affective as a commercial gym one. I say this because the pulley system look super closer compared to the ones in the gym that are spread apart more.

I found with heavier weights, the plastic guide inside of my plate holder comes out and interrupts my lifts.

Do you still think this is a good purchase? I'm thinking about getting one. They are $200 on Titan's website at the moment.

Were there any problems using the towers in crossover?

Where's "the other video"? For cable routing?

What size hardware is needed to mount it to your rack?

Can you do lat pulldowns on this?

How did you bolt it to the wall?

You should have showed us the rest of the video!

how long did it take to come

Did you buy new pulleys?

What happens if it’s not mounted

I hate commercials