No video :(

Toyota 2.5/2.7L AR Timing Chain Replacement, Cloyes 9-4313S

Подписаться 38 тыс.

Просмотров 124 тыс.

50% 1

🔥 This technical video from Cloyes covers the removal and installation of the timing drive system for Toyota's 2.5/2.7L engine.
🔧 Like what you see? Why not Join Shop Masters, our community for mechanics and techs who love what they do, take pride in their work, and are always looking to improve their skills. It’s free to join, and as a member you’ll get early access to all sorts of helpful videos. Visit www.cloyes.com... to see what it’s all about.
⛓ Part numbers related to this video are: 9-4313S, 9-4313, 9-5795, 9-5796, 9-5797, 9-5798, S1037
⚙️ Please see our online catalog at www.cloyes.com... for full details and to confirm vehicle fitment.
🚗 Application coverage ranges from the model years 1999-2013 and the following vehicles:
Lexus ES300h
Lexus NX300h
Scion tC
Toyota Avalon
Toyota Camry
Toyota Highlander
Toyota RAV4
Toyota Sienna
Toyota Venza

Опубликовано:

27 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 91

@seymourscagnetti1413 3 года назад

HANDS DOWN, BEST T-CHAIN TUTORIAL FOR THIS ENGINE.

@sonlightcommunitychurch5287 Год назад

Your three words saved me from a headache. My first time timing and I got it right. Thanks

@michaeljones-cy2oe 9 месяцев назад

You guys are awesome and I did buy the kit for the 2013 Toyota Camry 2.5 from Cloyes. Please keep the videos coming. Turned a lot of my customers onto you guys.

@pedrosanchez2230 4 месяца назад

VERY EXCELLENT EXPLANATION

@kellyclibern9042 2 года назад

Couldn't ask for a better how to video.

@FishingwithTarzan Год назад

Just Wana say thank you all data for som reason does not show certain timing procedures for vehicles only conplete overhauls these videos are som informative and helpful you can literally take these steo by step if need be even you guys are awesome !!

@marcokawar5459 2 года назад

These videos are awesome! Hope you keep uploading more

@Gpsautomotive Год назад

Best video on RU-vid for this job. 👌

@brettgooseauto4390 8 месяцев назад

AllData did not have instructions... thanks

@odishoodisho4904 3 года назад

Great as always thanks for sharing your knowledge

@Usmanthemecano 3 года назад

Seems pretty straightforward

@luissantiago147 Год назад

Great Video!

@jonathanbrand1270 Год назад

Awesome video

@shawnacano182 2 года назад

Thank You i been look for this video for years I'm upset this is my first time seeing it. i have pull my motor out three to connect the time cause of a crankshaft p s batch B, so a inline 4 only has 1 Batch A. still have the problem but car runs great. just will not pass cause if check light on. this is the best ar-2 video yea.

@hoobered1232 Год назад

great video. Can anyone confirm the parts quality compared to Toyota OEM parts?

@mrlover013070 3 года назад

Thanks, like always very helpful.

@gunnarmode 2 месяца назад

Great video just did that

@arthurmiller8336 2 года назад

Thank you great tips I like it

@samisolissolis6556 Год назад

Thanks

@OverlandOrange Месяц назад

Does motor need to be removed to perform this?

@cesarbriones2419 Год назад

Love it

@ralo20072007 2 года назад

Can the timing chain tensioner be replaced by taking that square cover off? Without the need to replace all other components or taking the whole cover off?

@peytonsilver5817 Год назад

Yes it can. It’s a pain though

@korno5718 3 года назад

I like it

@Silveradokev 6 месяцев назад

What did cloyes do to help with the intake cam phaser problem that these engine have , in developing a cold start rattle due to the lock in the phaser getting stuck ?

@user-eo9zm4eq5j 9 месяцев назад

I’ve installed both vvt sprockets chain kit. After finishing I now have a p0017 code. Before I had a p0016 code. I removed valve cover recheck marks. All marks line up. ?

@jhnmwaniki 2 года назад

Can you please do a video on 2.7 ar engine full rebuild

@rustbucket77 Год назад

Can both phasers be replaced with the camshaft still mounted on the head? I was told that the exhaust camshaft has to be taken out.

@enriquesilva8952 3 года назад

I like the video gracias

@accountingtax3417 Год назад

Hi Cody, what is the bolt size for the timing cover plate that gives access to the intake vvti sprocket and what the size of the bolt that hold the intake vvti sprocket in place. Thanks a lot!

@kellyclibern9042 2 года назад

Other than cylinder displacement, is there any other differences between the 2.5 and the 2.7? Could I put a 2013 2.5 in my 2013 Venza? It has a 2.7 currently. At a glance, they look identical?

@BennyTheButcher2 3 года назад

Just curious. Is this an engine-out or engine-in service? Guessing engine-in, as everything is accessed in the front

@JL4ever 2 года назад

Can easily be done engine in

@onebreath210 8 месяцев назад

I'm not sure if I'll get a response to this question or not, but I thought I'd try anyway. So you say if the timing cover is off and you replace everything (chain, guides, tensioner, and phashers (vvat-i gears) the phaser/vvt-i gears DO NOT need to be unlocked when installing the new part? So I'm taking that as if you are not removing the chain, just the phaser, that's when it needs to be unlocked for install?

@Cloyes01 7 месяцев назад

As long as you hold the camshaft while tightening the phaser bolt, you do not need to unlock the phaser. The only way you could damage the phaser is if you tighten the phaser bolt while using the chain or another shaft to keep the phaser from turning. That would put pressure on the internal locking pin.

@onebreath210 7 месяцев назад

@Cloyes01 good to know! Thank you for the reply

@pauca2014 3 года назад

What are the cost of a chain replacement? I have a highlander base 2006 4 cyl.

@timocrosby 3 года назад

I got it all installed and the car runs like new. Thanks for the video!

@chucke3305 2 года назад

@@timocrosby how much they charge you?

@nathanstander1493 Месяц назад

That crank pulley looked more like 11 o'clock, but I guess pointed up in general?

@Cloyes01 Месяц назад

Correct. The main focus is making sure the marks align. You can make small adjustments to the shafts if needed.

@nathanstander1493 Месяц назад

@@Cloyes01 thanks for responding

@derakbell8143 2 года назад

Man I really wish you would have showed where you put sealant on the front cover and what type. Tensioner bolt torque value? This crazy easy and plan on doing this on my camry this winter. 2011 2.5. Has currently 214,627 miles on it. Im doing both cam phasers as well.

@RAMJO 2 года назад

Hi derak, is their reason why you decided to do this my 2011 Camry has 120,000 miles. Little rattling noise started a couples months ago, but now it’s got to the point that when engine is hot and I try to turn on the car it takes a couple seconds. I turn the key and it sounds like it’s gonna shut off. I hear the crackling noise then it’s stops. When driving it runs fine no problems at all.

@singhsarabjit Год назад

Hello Sir, Thank you very much for this video. I followed steps, Put chain on all the timing marks. But when I turn engine by hand, yes I turned engine 5-6 times but still chain marked links are matching, did I do something wrong? engine run fine after I put back together but it does through code P0017. Please advice. Thank you very much!!!

@orpiv 2 года назад

I have a noisy 2009 Toyota Venza especially on cold start .. Is this the same kit and install?

@Cloyes01 2 года назад

Yes, if it has the 2.7L.

@chalinoahuesoduro5566 2 года назад

Whats tge torque on the tensioner bolts?

@adilabilbekuly 2 года назад

Hi! Is it possible to replace only tensioner without opening top cover cap just by opening small cap in front side of engine?

@Cloyes01 2 года назад

If you remove the tensioner cap you will need to remove the tensioner and deactivate it. Upon reinstallation, the valve cover will need to be removed to activate the tensioner against the chain.

@ralo20072007 2 года назад

@@Cloyes01 I've heard you can just rotate the crankshaft from outside until you hear a few clicks indicating the tensioners been activated. Will this method work?

@loganburnett677 2 года назад

If there is damage to the crank reluctor wheel you can’t just replace it you have to replace the entire crankshaft or am I missing something?

@lt1swapgonzalezperez102 Год назад

That's what I'm trying to figure out I can't find anything online I'm trying to buy the reluctor wheel but can't find anything I'm guessing it comes complete with the crankshaft

@Andy-ue3dv 3 года назад

So if only replacing chain/guides/tensioner, and reusing camshaft gears - Do we need to “advance” the intake camshaft gear like the FSM states?

@Cloyes01 3 года назад

If you are not removing the phasers there is no need to follow the phaser unlocking/advancing procedure that Toyota recommends. That procedure insures that you don't load the phaser's internal locking pin while torqueing the attachment bolt.

@chukwumaedwin5484 3 года назад

I changed my top gasket after changing the top gasket the engine started making noise rock rock rock rock rock rock

@wilsonharlot4435 2 года назад

If this same engine (Toyota venza 2ARZ) has knocking sound, once steam for 30mins time, what is it remedy

@writeupking 5 месяцев назад

Engine replacement 👀.

@HandyTim 3 года назад

Should the bolts be replaced with new torque to yield bolts?

@billanderson5774 Год назад

The cylinder head bolts are torque to yield, and should be replaced with new bolts, which must be purchased separately (unless a rebuild kit specifically includes those). The vvti camshaft phasers also are torque to yield bolts, but new bolts should be included with new gear(s). If you are replacing head gasket, I would also recommend replacing the vvti phaser gears.

@Thebombonlyone 10 месяцев назад

No torque spec on the chain tensioner....

@user-pu3kg9rv5y 3 года назад

👍

@dieselscience 2 года назад

My only complaint is that guitar riff is for Volkswagen, not Toyota.

@sonofsteve566 Год назад

Hi, during installation that slack between the phasers is normal? no matter how hard i try i cant element little play.

@Cloyes01 Год назад

Yes, some slack between the cams is normal. Both camshafts are dealing with valve spring pressures. Sometimes this will cause the cams to want to clock towards each other creating that slack. It really just depends where the engine stops as to what spring forces are against the cams. This can create slack between the cams, or between either camshaft and the crank, and it may shift the next time you turn off the engine.

@sonofsteve566 Год назад

@@Cloyes01 thank you for your response, that slack appears to create the chain to jump teeth, when the crank is turned. I'm guessing chain stretched ? or the tensioner is not doing its job.

@Cloyes01 Год назад

@@sonofsteve566 Both are possible if it is a used system. But turning the engine over by hand does greatly increase the chances of the chain jumping because of the violent movements of the camshafts due to the valves opening and closing and no oil pressure going to the tensioner. Even a healthy system can jump time when turning the engine by hand. Rotation with the starter is fast enough that the chain slack doesn't have time to shift back and forth which is what allows it to jump teeth.

@sonofsteve566 Год назад

@@Cloyes01 one more question please, original phasers, is there a concern of them locking when chain was removed did not hold cam when tensioner was removed. if cam phasers locked would this create a timing jump at crank?

@sonofsteve566 Год назад

@@Cloyes01 appreciate your effort in helping me out on these questions.

@tracypolockowbrooks Год назад

does the engine need to be removed to replace the timing chain?

@billanderson5774 Год назад

@jamesbonesteel2501 Год назад

@@billanderson5774 Seems like there is no way to get the timing cover out. I have loosened all motor mounts lifted motor and still can't get it out. How do you pull the timing cover out without without pulling whole motor? 2010 rav4

@jamesbonesteel2501 Год назад

Was not being creative enough and jump the gun on my question. Had to go through the bottom with engine as high as it goes.

@billanderson5774 Год назад

@@jamesbonesteel2501 Support the engine with a jack under the oil pan. Place a board on the jack to distribute the weight across the entire oil pan. Then remove the RH structural brace that extends from radiator support to (iirc) frame/sub-frame. Once that brace is out of the way, the timing cover can be removed by sliding it out thru the bottom of the car. You may have to also jack up passenger side of car to create extra space for timing cover removal. Make sure to support car with jackstands

@skygirl341 Год назад

So just to be 100% clear I don’t need a timing lockout tool to do my timing on the specific motor so I just wasted $89?

@Cloyes01 Год назад

The tool is not required, we did not use one in this video, but it can be helpful.

@timocrosby 3 года назад

HELP! Why is it that my intake camshaft will not rest in the 11 o'clock position? It snaps forward to the 12 o'clock or back to the 10 o'clock position.

@Cloyes01 3 года назад

You are experiencing valve spring pressure as one of the valves are open. You can move the cam to either the 10 or 12 o'clock positions and time the engine. Just know that the other camshaft and the crank will also need to move slightly to get the marks aligned. As long as all three marked links are aligned to their respective sprocket marks then the engine is in time.

@timocrosby 2 года назад

Yep. fugured it out. Thanks!