Trex 150 DFC Setup/ Bind Procedure for Spektrum Radio systems 

Thanks for explaining things thoroughly, it helps because I've never binded an Align heli to a Spektrum transmitter. In a lot of tutorials people skip over certain details and assume the viewer knows about those!

Great video, My first few flights went really good on a windy day. Thanks for the video.

I thought my Trex 150 was dead until watching your video. Thank you very much

Thanks for the setup video, helped me get my basics to setup my new 150 DFC to my Spektrum DX6 radio. At first I found the cyclic's to be very slow and sluggish and found info on adjusting the rate pot from the default lowest setting (looks like set at 8 o'clock postion and set to 12 o'clock position), I may yet increase the cyclic's as it seems still a little slower than my other heli's. However, I'm having problems getting my tail dialed in. It does not feel locked and noticed that it has quite a bit of drift. I've only hovered a couple times in Normal Mode and per video had the Gyro set at 50%, I also have tried increasing the settings (tried 52%, 55%, 60%, and 65%). The tail still does not feel locked in and I'm not sure what else to set. I can try to keep increasing the Gyro above the 65%. I also notice a small amount of tail wag right out of the box, even when the gyro rate set at 50%, but didn't notice any increase with the tail wag even up to 65%. I'm mainly wanting to get my tail to feel locked in so I can have confidence in controlling my brand new heli (rec'd yesterday afternoon). So far my other heli's are a Blade Heli's (Nano CPX, MCPX V2, MCPX BL, 130X, 180 CFX, and a 300 CFX), so far the tails on those heli's have been very responsive and feel locked in, (except for the MCPX V2) that encounter's occasional tail blowouts with flips. This is my first Align FBL heli and if I'm able to get my 150 DFC dialed in and flying great, I would be interested in some of the other Align Heli's like the 250 DFC, 450 Plus DFC and/or the 450L Dominator. And later move to the larger ones as my skills and confidence get better. Anyway, any help with getting my 150 DFC getting its optimal setup would be great. BTW - I haven't changed anything on the Gain Pot, looks like default is 12 O'clock position. What will the gain pot control? Will that help get the tail to feel more locked in vs the gyro settings on my TX? Thanks, Joe Roanoke, VA

Thanks for such good video! But I have a question! : Can I use same settings for T-Rex 700N (gas version)/ Or what pitches I should set up for it? Thank you! :)

Hi Jeff, when I bind my DX6i in DSM2 (with a DSMX receiver) I get one green and one red light on the main board - what does that mean? I didn't see this in the troubleshooting section of the manual. Also, I'm unable to get a bind on the main board with the DSMX binding procedures (the light is solid on the satellite system but not activating the actual board.) Any thoughts? Thanks for the great video!

i have the dx9 and i bound it to my tx and im still only getting one steady red led light?

Well I have two flights on the heli after just binding it and when I move the rudder left or right the heli will not pirouette flat the tail kicks up and the nose goes down a bit in both right and left directions no matter if it's Normal, ST1 or ST2. Is there any adjustment I am missing?

Thanks for the help Jeff. I have a Dx7se which is DSM2... but at 11ms. Am I ok to leave it at 11ms? Also have run into a little problem with throttle on Normal mode. It won't shut completely off. Even though my normal curve goes all the way to 0, it still outputs a value of 1. Throttle hold shuts it off and when I arm throttle it stays off. It just won't stop when spinning. Any thoughts? Thanks again.

very helpful video,thanks.

good job jeff liked

can't get my trex 150 to bind with a spectrum DX6i… trying to bind it with a spektrum spm9645 dsmx sat receiver with no success. any tips to get to work with a DX6i transmitter

Do you have to leave the dsmx satellite in the helicopter permanently after binding or can you unplug it and take it out?

How does head speed effect tail hold and twitchiness?

Between the dsmx and dsm2 which are the diferences, any better?

Pitch at 70 70 gives more than enough pop for me. Also if you run more than 12 degrees you can load up the rotor system.

Can we get just s little help with a dx7 and like I have a dx7 and have no clue how to set the gyro up. I would like to fly this new bird. Im not a pro with set up.

this setup goes for the new dx6 too right?

and would dx6 work on the heli as well ??

Funciona neste Radio Spektrum Dxe 6ch 2.4ghz Dsmx Dsm2 para o T Rex 150

Is this a good one for a beginner? What radio is recomended?

Jeff Can anyone help me i am trying to get my dx6i to work on trex 150. i see all videos and they show how to set up dx8 but not dx6i thankyou

Most lilkely will have to use mode B in the JR Radio.

Both settings will work, but the settings I provide for radio are direct out of the manual.

Hello Jeff, do you happen to have the settings for the spectrum Dx6i settings on your page that you could post, would really appreciate it. nice video but with you would have focus closer in the settings for the transmitter thank you hope to see more videos

It is the same for the DM6i?

Hi mate,will my tx jr dsx9 bind to trex150?

boa noite amigo, como eu bindar em um 10j rádio futaba?

Hi Jeff, thanks for your video. I would like to know if I can use sub trims on pitch servo son that I can set 0 degrees at 50% collective because my 150DFC is at 0 degrees at 40% pitch. Thank you.

I mean can this heli bind to the dx6i transmitter

Hi can this heli bind to the dx6s transmitter

Assign Gyro to your Gear Channel and then use about 70% gyro gain. Adjust as needed to your head speed.

Y do futuba have servo center and sprekem don't liked

Thank you good Video ;-)

Hi Jeff i was wonder if you can bind and then 3D fly the Trex 150 with the Spectrum DX6i?

hey bro , does every remote comes with that lil black box that goes under the heli??

Is ther something different for a dx7 I just got my 150 and would love to fly it but it seems I copy the settings from your dx8 and I just cant get it right.

Give us a call at 562-598-4700 if your having a issue with setup and or binding process. As for setting, they must be entered by you in your radio.

binding procedure by a guy with name that sounds like "fast binder" priceless.

The battery cage on this heli is rubbish. Should be a wire like all other helicopters.

Get the fuck rid of Futaba remotes they are complete trash next to any spektrun

Y do futuba have servo center and sprekem don't liked