Tuning A 2-Stroke RC Car │ Ezeetrade Racing 

I've owned and tuned rc cars for years and i can say its one of the best tuning videos i've ever seen.

Straight to the point. No BS hears what you have and here’s how it should react simple. Awesome job man thank you

Mate your a legend ! Just got my 9 year old HPI Baja 5B running again, with a new plug & fuel and priming bulb, your base setting is gold thank you

Great video, this is the only video show how to tune right. Thanks for sharing now my rovan Slt is running great.

Great video mate 👍

Thanks for you help my truck good tuning now 👍

Great video thanks!

Yay you’re back I missed you!

Great vídeo Bro.

Nice info video 👍

Top dicas irmão 🤩👍🏻✌🏼🏎🔥💨

Nice mate

3:20 is the critical moment in this video to me. Closing both needles proved my Rovan 29 can start no problems. This info was critical to me, as I don’t like to change plugs and carbs for no reason. Furthermore my engine only idles with the LSN at half a turn out. I know that’s crazy for a Walbro carb. You would think it’s too lean. So either it’s note getting enough air or….? Time for a carb tear down and filter clean I think

Thank you ❤

I just buy a baja b5 and the carb was bad i put a new carb and follow the video its just amazing the best video for tune carb!! I just have a question they smoke but roll good i dont know if is to rich or my mix gaz tanks you best video!!!

thank you buty my buggy standing long time would not start be cus you show me what to got it in just 2 mins thanks buty your the best have nice day

Excellent video! I do have a situation with my 5b baja that I just purchased. It sounds like it is tuned correctly but it basically goes from idling & with the slightest touch to the trigger it sounds & acts like its 3/4 throttle. I'm leaning towards either incorrect linkage setup for throttle & brake or incorrect setting with my radio? Do you have any suggestions? Thanks in advance!

Tune with choke open or close ? And run the car with choke open or close ? Thank you great video

Hi I wanted to ask see when you flood the engine have you ever tried removing the carb and pulled the starter to fire it up to clear it, then put the carb back on and started it up

Can you make a video on how to seal the head without using the base gasket please bro. I don’t know how much to apply and what pattern I should do!

After the low speed and high speed needle are allset should we turn the idle screw back until it doesnt touch or just put it where it is?

@EZR I installed a gas kills switch for my car and I had it running then i messed with the low needle screw and idle and now it still wont start but pops once then yanks the pull cord out my hand. I cant figure out how to resolve the issue and to get it running again i would love some pointers. its a 30.5cc with a tuned exhaust.

Please make more videos on tuneing

Can I do the same for my 1/5 scale hsp mxt5 warrior which has a zenoah engine and the carburetor doesn’t have the choke. And I also need to know what’s the cc on this rc or how can I know what zenoah model is exactly equipped on this rc ?

so I have a brand new rovan Baja with a 36cc engine, I can get it started but it will only idle for ≈30 seconds and then die, it also dies if I give it any throttle, what's the issue?

Are gas rc cars easier to tune than nitro rc cars? I had a nitro and it felt like I had to tune it every time I used it. Eventually I gave up and went electric but I'm interested in gas because I was told they are less work to start and maintain than nitro. Is that true?

Interesting way of tuning, never heard nor seen someone open idle all the way then go from there.

So with the base tune of idle screw all the way in n high n low 1.25 out it can been ran like that? Or is that just to get it started?

Do you have tips on diff oil? I have an early 32cc 4wd. Same as redcat dune runner

Hello I tried your way on getting my baja started Thanks But when I am trying to tune from there it blog when I hit throttle and cuts off Which way I go with the needles

Can you do a video on tuning the king motor 2 speed trans? I cannot seem to get mine to shift at all. And the button head screw always backs out everytime I use it. I dont really want to put lock tite on it becasue I want to tune the gear shift points

Hey bud my fuel line has bubbles and the car starts but doesnt stay long its stips whwn the throttle released how ever where the gas intake pipe it moves around .

I can’t get my car to idle, will this work for it? It starts but won’t idle and just dies when I take my finger off the accelerator

Hi.. my rovan 32cc engine dies after i release my throttle at full even without using brakes. What should i do? TIA

How about the high end niddle? How to tune it ? Cause all i can see in this video is the low end niddle adjustments

What do u mean if the revs climb open the idle screw abit how can you tell if the revs climb

My baja 5B the tune is perfect low and high speed needle. It’s just when I brake and hold the brake on it wants too cut out after a couple of seconds?Do I need to turn the idle up on the carb just a touch? Or should I adjust the end points for the braking on my transmitter?🙂

Just a question. I am gonna break in a new engine 32cc. What’s the best temp before I shut it down for a cool down Thanxs

Hey bud I replaced a new carb but since it's stock setting it should start and good to go right but how ever it sometimes starts and runs sometimes it's stops when I throttle or sometime it won't start at all

Hi, I can’t get my baja to start what so ever, I’ve checked the spark plug gives a spark, I’ve even gotten a new walbruro carb, I tried a roto start, its just dead, Took the head off cleaned everything with petrol, piston and sleve still good, put it back together, still nothing.

Hi I installed a brand new 990 carb on a 30cc. Now she won’t start at all it’s like no fuel even getting in to the engine. I have tried everything. Low speed needle 1 1/8th turn and high 1 1/4 turn. What should I do thanks

I just replace a new engine to my baja 5t and I want to put my carb settings to factory then break in to the new engine, please help

I have a Rovan 45cc Baja and a WLT.🙃

Hi I tried tuning now it wont move but it revs really really high how can I fix this

My 2 stroke don’t wanna start recently but does once in a while and I’ve tried everything and I’m thinking the spark plug is on the way out. I don’t have a clue on why. Update I got a NGK spark plug worked perfectly now after the first start i let it run to let the spark plug sit in properly if its even needed. I let the tank run through and the following day it don't want to start again I also checked the flywheel and the ignition coil thing and still got charge on pull while electrocuting myself testing it and unflooded the engine to check but once the spark plug is in it don't wont let me pull start it like there is a shit ton of compression build up. I done everything I could think of like holding the throttle while the spark plug is out and pulling the pull start to unflood the engine if it was did that for 10-15 pulls put it all back together and still don't wanna budge. I'm going to order a new carburettor since it has sat for 4 years and it did run perfectly for the first 2 days and is starting to play up since. I also checked the piston and it look perfectly fine. I'm hope-ing the carb is faulty since its not ran for 4 years and I'm guessing it keeps leaking fuel into the engine. Any advice would be grateful.

My idle is crazy high if I don’t back off the idle screw. Whats wrong with my carb?

i picked up a km baja with a rovan engine

Hello my spark goes black very quickly and I’m finding that I’m replacing it more than I should could that be because it’s to Rich and if so am I safe to go back to default settings like u showed and opened both high end and low end 1.25 turns out will that be sufficient until I get going

This sucks glad I moved to battery rc cars

I hate 2strok engines in Rc . Never ever start esely . Install new carby .if start struggle to run . Rubbish 2strok engine jus wasting money.