Under sink Mini Tank Electric Water Heater Install

Подписаться 30 тыс.

Просмотров 110 тыс.

50% 1

Under sink Mini Tank Electric Water Heater Install
Bosch Electric Mini-Tank Water Heater Tronic 3000 T 4-Gallon
amzn.to/3H82qpB
**If the video was helpful, remember to give it a "thumbs up" and consider subscribing.
Subscribe for new videos every week.
Follow us on Instagram
woodelldani...
Subscribe for more DIY videos
/ dwoodell12585
Like us on Facebook
/ daniel.woodell.9
Disclaimer:
Due to factors beyond the control of Daniel Woodell, I cannot guarantee against improper use or unauthorized modifications of this information. Daniel Woodell assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Daniel Woodell recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Daniel Woodell, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Daniel Woodell.

Хобби

Опубликовано:

27 янв 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 107

@burts6896 Год назад

I'd recommend mounting the water heater a little bit off the floor so that leaks are easier to see and detect.

@unti419 4 месяца назад

I never had a problem with cold sink water until I had to replace my bathroom faucet with the new low flow set. Now I have to turn the hot water on and walk away for a while. I'm looking at something like this. It's looks like a simple install, and I have a dedicated 120v circuit a few feet above where it needs to plug in. I can pipe it into the existing hot water line so hopefully I can use a smaller version of this, need to do the math. Thanks for this video.

@ericthesure9002 6 месяцев назад

It looks like a non GCFI outlet and you have the relief valve pointed straight at it. You could plumb it to point it down.

@Merescat 2 года назад

Very nice! Another video for something I will be doing in my shop. Great video! Look forward to the next one.

@mr.crighton9491 25 дней назад

you did a great job prepping everything for a professional install. My only question is the direction of pressure release valve. Do you plan to re-route it away from back of cabinet? great job! I'm facing this now.

@B2C2007 6 месяцев назад

Amazing how many of these vids don't show the final result and actually discuss the performance. A couple of shots at the end with before/after or just the flow and warm-up time.

@benwarner5389 3 месяца назад

Thank you. Great detail. I am building a bar in my pavilion and need hot water for clean up.

@tomclose390 2 года назад

great job hooking one up in my outdoor shed i made for toilet and sink

@user-bs5ph1dh1y Год назад

Excellent video Everything covered

@irishhandyman2009 2 года назад

Liked the video. Please do a follow up later on as to how well it works and if you have any problems. I have a situation were something like this would help.

@mobilesushibargirl 2 месяца назад

what type of disharge pipe for t&p valve did you install? thank you!

@sarahmoore4917 Год назад

why did you install stop valve on out going hot water?

@nigel8247 Год назад

No expansion vessel? No pipe for the pressure relief valve? If it went of straight over the power supply.

@LotusDetail77 5 месяцев назад

you think this could would in a mobile detail trailer if plumb right?

@jstrada3190 Год назад

How long did it take for it to heat up for the first initial use?

@charlesphipps963 7 месяцев назад

Does anyone know if this has to have constant water supply or would I be able to fill it as needed?

@JestersRune 2 года назад

Great video! Concise and easy to follow. Well Done! What about the relief valve? Is that fine to leave unplumbed?

@dpky7333 Год назад

No the relief valve should be plumbed to drain since it is in a finished space.

@geraldbennett7035 Год назад

@@dpky7333 cant do that because of potential for sewer gas/water to back fill into water heater. Have to plumb to outside of building.

@dpky7333 Год назад

@@geraldbennett7035 in warm climates, that's correct. Otherwise to drain with 1" air gap. However under a sink it's tough because the air gap creates the potential for a clogged trap to spill out through the gap instead of filling the sink. Since a mini water heater can easily be removed, I think it comes down to whatever risk the occupant is willing to take. Backflow risk vs. Scalding risk vs flooding risk. But I think we agree that leaving the t&p valve as is is unacceptable.

@tomclose6643 Год назад

how do you drain water out of unit ?

@bikerjon153 9 месяцев назад

What about the pressure relief valve.

@suallahhalid3241 10 месяцев назад

How can the water (heater) flow wel since it’s under the sink pls

@kat4animals004 Год назад

Would it be ok to install this on the side?

@jimmiemack1947 Год назад

Great video! Is it better to vent (pipe) the relief valve to the drain pipe?

@mborski1000 4 месяца назад

I was wondering same

@cahmarcomsonnyk.320 Год назад

How much electricity cost to keep on all time, using occasionally. Mine costing £50 a month i use occasionally which is huge! !

@cristianmazariegos2163 Год назад

I installed mine lying on the floor because I didn't have space to put it upright. is that a serious mistake? Please someone help me . Thank you

@MrCoach1957 Год назад

Ya, so where did you say I could find someone to install this for me?

@stevethach3340 2 года назад

Hey Daniel! Thanks for the video! I do have a dumb question for you, how does the water travel up the line from the water heater? Pressure? Or is there a motor? Thanks!

@craigs66 Год назад

pressure

@homeofthefree8656 6 месяцев назад

City water is what he connected to, city water is designed to have a certain pressure behind that water. Maybe 40-80psi or something, idk. If he was off grid and had a water tank lower than the sink in elevation, then he would need a pump to get the water around the house. OR mount the water tank on the roof and use the “gravity” to pressurize the system

@danburland7190 Год назад

Should you have plugged it into a GFI or would it trip the GFI everytime the water heater turns on?

@jimeagle1155 8 месяцев назад

It is It's supposed to be connected to a 20A GFI outlet. If it trips then there is a shirt or pulling too much amps. Any outlet dealing with water or in the vicinity of water ot outside must be ground fault protected

@garagekeys 2 года назад

You probably want to put a discharge pipe on that t&p valve so it's not aiming right at the plug that you have right there

@jeffwillis427 2 года назад

and to a location not effected by water

@Rickzabor Год назад

How would you suggest plumbing the t&p valve? I don't have an easy drain location. What did you do?

@Rickzabor Год назад

How would you plumb the t&p valve. I don't have a local drain

@landonheadrick1775 Год назад

Worst case, run it down into the crawlspace and hopefully catch a drain down there. Worst case, the crawlspace is better than discharging into a finished cabinet

@williammontgomery3249 11 месяцев назад

Good vid, thanks. A water pressure vent almost never happens at the heater. In my house, a failed expansion tank caused an increase in pressure. (Hot water expands.) The hot water heater exploded first. I heard it pop. I went to the garage right away and checked everything out. The 3/4" "vent pipe" outlet didn't work. 55 gallons of water were on the floor and the water was still flowing... Good thing I was able to hear the heater from upstairs in the house, (18 year old Goodman, common choice with builders). FYI I installed the new heater with two expansion tanks in the closed system. They are cheep... ($20) but only last so long... Available at all home improvement stores. Having two expansion tanks and a pressure gauge at the hot water heater are a must if you have the space to do this.... I have 3 tanks now with pressure gauge watching the whole closed system. (closed system: Basically, if you are heating water and no valves are open, your system is closed and the water pressure will rise.)

@KevinGarcia-ix6tz Год назад

Do you get hot water on your shower???

@TheLukemcdaniel 2 года назад

I think I'd rather have a tankless under the sink, but I've really been considering one of these for our bathroom, since it's on the opposite end of the house from our heater

@DanielWoodell 2 года назад

I looked at the tankless a lot but the price difference and the power requirements in this application just really didn’t work out for me.

@danscolardi1499 2 года назад

The electric tankless is plagued by the 'sandwich effect' (check online for this) which I hate. A small tank is far better for kitchen sink.

@ericvisser113 Год назад

@@danscolardi1499 you can avoid the sandwich effect where you have a whole house tankless heater and a point of use (POU) tankless heater. A cold water sandwich may be created by the whole house heater which is then corrected by the POU tankless heater. That is the setup I have in my house with the tankless point of use under my kitchen sink. However the drawback is my 8kw 33 amp POU heater can only keep up with a modest 0.5 gpm flow... You would need a 11kw or 13kw POU to heat water at a 1.5 or 2 gpm flow which would require something like 6 gauge copper wire on a dedicated circuit (not cheap).

@manoloelcojo 6 месяцев назад

Relief valve , expansion vessel??

@ihop4no14 Год назад

Appreciate the video. I bought the Bosch Tronic 3000 T 2.5 gallon unit and am attempting to install it. A couple of questions: 1. I have an existing system with TWO supply lines, hot & cold, to my current sink. Both have shut off valves. 2. Would I disconnect my COLD water supply & connect it to the IN (blue) connection on the unit? 3. Then run a supply line OUT of the unit to where the sink gets water? 4. Or would I disconnect the HOT water supply, connect it to the IN (blue) connection on the unit & then OUT to the sink?

@DanielWoodell Год назад

Leave the cold water supply alone, you will connect the hot water line to the water in side of the water heater then connect the outlet side of the water heater to the sink.

@DanielWoodell Год назад

So number 4

@phoradio1277 Год назад

@@DanielWoodell What if you are installing in an RV that you have a 30 gallon tank gravity feeding the water line? Can I just connect my current line running from the sink directly to this or do you need hot and cold lines. I didn't bother to run a hot water line even though I have a propane water heater based on the logic I was planning on buying one of these to just give me hot water. You know what my direct question is can I adjust the temperature of the water or what you see is what you get? Built an entire RV from ground up can't figure out running water😂 Sounds about right

@raffelscott7696 Год назад

My mini hat water heater is leaking how can i fix it?

@JDunigan88 Год назад

I already have a whole-house tankless water heater in my basement. I want to install one of these under my kitchen sink but I don’t want my main heater to kick on every time I use this. Can I put a T fitting off my cold supply line under my sink, so that it feeds the cold faucet and the under sink heater, and cap my hot line under the sink?

@DanielWoodell Год назад

Yes

@dianetavernier4195 6 месяцев назад

Can you have ind in the kitchen and one in the bathroom? Could it be used to fill a bath?

@DanielWoodell 6 месяцев назад

To small to fill a bath

@bilhep Год назад

What about the overflow connection?

@MikeCarey101 Год назад

Would it make sense to connect the cold water supply to this and not the hot water? My bathroom sink is across the house from hot water heater, so pulling hot water to refill this tank would not get any hot water from the heater before it is full. This would just waste the hot water in the line.

@TTW1 Год назад

I don't think this is a booster for an existing water heater.

@ELBENDC2 3 месяца назад

This guy never showed how to operate the unit, i know is probably simple but please make the video complete for people who never have seen it 😮 wow

@computerterry618 Год назад

About how long did it take to heat the first fill?

@DanielWoodell Год назад

About 10 min to hear the water to a comfortable hand washing temp

@thewifemommylife8238 2 года назад

Do you know how to drain one of these ?

@jamesfrederick99 2 года назад

Turn off water supply line. Disconnect unit from supply and discharge water lines. Unplug. Then you must let it cool down for 8 hours. Lift the unit up and invert it over your sink. Water will drain out.

@johnspittle9642 8 месяцев назад

can you extend the power cord? It's pretty short.

@DanielWoodell 8 месяцев назад

If you had a properly sized extension cord it would work, how ever water heater are usually expected to have a plug in close by usually and electrician adds or relocates a plug in to the location that the heater will be located.

@markmckinlay99 Год назад

Am I missing something?? Why do you have a separate water supply feeding the heater and then another supply line (the red one) going to the cold water side of the tap? Are they both cold water?

@DanielWoodell Год назад

Yes the are both cold, I ran out of blue half inch pex, when I was plumbing the shop.

@nosxillz_4115 3 месяца назад

@@DanielWoodellso technically I could just connect a hot water line and cold water line to this?

@nosxillz_4115 3 месяца назад

Or am I missing something because shouldn't you have 3 lines at this point 1 cold water line and 2 lines for hot water one from the supply line into the unit and from the unit to the hot water line on the faucet?

@nosxillz_4115 3 месяца назад

Or should I be installing the hot water supply line to the blue side then from the red to the sink?

@carlosreyes6448 11 месяцев назад

What size breaker, do you need?

@DanielWoodell 11 месяцев назад

20 amp

@dpky7333 Год назад

I can't imagine how anyone would be able to get 4 gallons of water out of a 3/8 line in 5 seconds. Did you cut the video or was there actually still air left in the tank.

@sean13 2 года назад

Dad just installed this in his place to save electricity but now he only gets a few minutes of warm water in the shower. Any idea why? Low water pressure, low volume. Thanks!!

@DanielWoodell 2 года назад

This type of tank is designed for a sink only gallons provided and the on-demand feature or not read it for a shower.

@jimeagle1155 8 месяцев назад

This is not meant to supply a shower.

@seansalas3474 2 года назад

If this is under a kitchen sink with an existing hot water line, does the hot water line go to the bosch unit instead?

@DanielWoodell 2 года назад

yup

@seansalas3474 2 года назад

@@DanielWoodell Thanks for the quick reply! It's been a little over a month... still happy with the unit?

@ihop4no14 Год назад

@@DanielWoodell So does the hot water supply pipe go to the Cold Water Inlet or the Hot Water Outlet on the Bosch Unit?

@leejones6579 2 года назад

What about the prv .have you got your unvented certificate to install this

@tc9730 Год назад

Who cares if he does or doesn’t.

@Lakesidearmorer 2 года назад

GFI outlet needed, and plumb the over flow temp/pressure valve away from the unit.

@DanielWoodell 2 года назад

That outlet is GFCI dedicated 20 AMP breaker in the panel, and yes the relief line should be plumbed outside, but it’s in my shop and I build the cabinet if there is a issue with it I’ll be the only one to blame 😁

@Lakesidearmorer 2 года назад

@@DanielWoodell Hi Daniel, That is good that it is on a gfi circuit. But it would have been a good point to mention, as some viewers might no know that it should be. As far as the relief valve, you're right it's your $200. I really did not mean to sound like a 'B" buster. George

@Lakesidearmorer 2 года назад

@@DanielWoodell BTW I did enjoy the video!

@KenJames9911 Год назад

No GFCI?

@jimbolen6364 Год назад

Could be inline with another plug.

@rocketstar9067 Год назад

It's called a water heater.

@toucansam3217 Год назад

It is a water heater, not a hot water heater

@randyweb6791 2 года назад

PLEASE stop calling it a Hot water heater. If anything it’s a cold water heater, or just a water heater.😀

@joejr1967 Год назад

Never understood why you would need to heat hot water 🤔

@Deliverance-Childrens-Bread Год назад

119 ministries RU-vid the sabbath day video you'll want to watch it.

@AlvinBrown Год назад

@@joejr1967 it is called a hot water heater because it heats water

@danielhall3595 Год назад

No it’s not. Hot water heater is redundant!!!!

@tmkinnear Год назад

Wouldn’t the hot water supply line from the house connect to the cold water supply to the little tank? As you run out of hot water from the little tank it will be filled eventually with hot water from the larger house hot water tank, assuming you kept the hot water running long enough in the bathroom sink. 🤔