Valve Cover Gasket Replacement for 08 Malibu 3.6L

Подписаться 183

Просмотров 12 тыс.

50% 1

Today we're replacing a valve cover gasket on a 2008 Chevy Malibu with the 3.6L. This is a general overview of a "how to" to remove the intake manifold, electrical connectors and FRONT valve cover.
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing for future videos.*
Disclaimer:
Due to factors beyond the control of Cars, Trucks and Coffey, I cannot guarantee against improper use or unauthorized modifications of this information. Cars, Trucks and Coffey assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Cars, Trucks and Coffey recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Cars, Trucks and Coffey, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Cars, Trucks and Coffey.

Авто/Мото

Опубликовано:

18 июл 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 25

@truckscarsandcoffey3973 3 года назад

Thank you for the feedback everyone! However, no more videos of this car will be coming as the owner no longer has it due to an accident. They are fine. When I have more time from work, look forward to more videos!

@327JohnnySS Год назад

You don't have to remove the fuel injectors. Once the upper manifold is removed remember that the 4 long bolts are in the center. The rear valve cover to be removed only takes a 1/4inc on swivel with a 10mm long socket to remove the the bolts on the back of the valve cover. You will have to remove the wiring harness tabs after you have removed the 2 10 mm bolts from the power steering reservoir. You will also carefully gently remove the valve cover. Also remember that you only have to loosen the bolts as they cannot be removed from their grommets. To install the rear valve cover after cleaning apply some Indian gasket goup slightly to the valve to keep the cover becoming dislodged during installation. Never forget to clean the surface on the left side of the engine where the timing cover meets those cylinder heads. Use a small dab at those points of a silicone that is rated for oil resistance. The black, blue and high temp orange will seal. Just wait about 7 minutes before installing the rear valve cover. You will also push down to get the new spark plug tube seal with a slightly coat of oil. I hope that this helps anyone. 👍🏁

@gprice932 3 года назад

Great 🎥...And Explanation

@truckscarsandcoffey3973 3 года назад

Thank you! I am happy you found it helpful!

@melholloman5467 3 года назад

This was awesome! The is the only vid for this car on valve gasket that I could find. Totally got it. Did snap a bolt that I'll have to easy out. Car did not start afterwards so not sure what to do there. And now, I need to do back half. Omg... could use some help there for sure!!

@truckscarsandcoffey3973 3 года назад

I'm glad you found this helpful Mel! It was probably just a plug somewhere keeping it from starting since so many were unplugged.

@zipzay2037 11 месяцев назад

Lucky him mine just started leaking in the back

@kayudoe1874 7 месяцев назад

9:42 how did you get those out of the slot?

@josephrodriguez7084 2 года назад

Could you do a video on replacing the rear gasket?

@truckscarsandcoffey3973 4 месяца назад

Can't. Vehicle was totaled 3 yrs ago.

@cartroublewannafix8611 2 года назад

Is there a way to adjust the timing without marks? I took the chain out and my stupidity allowed me to turn the the sprocket s individually, which turned the cams. Now I have no idea where I am at. Call me an idiot because I am. 2015 Chev malibu 2.5

@babyred0789 3 года назад

Next time you replace the valve cover gaskets can you plllleeeeaaassseee use a tripod so we can see what you're doing in real time? Currently need to replace mine but I feel like a lot was lost in translation without being able to actually see you complete each step Thank you!

@truckscarsandcoffey3973 3 года назад

Thank you for the feed back. I am looking into getting a tripod. I just filmed this on the fly and found this was the easiest way to edit at the time.

@bendowney287 2 года назад

Was there still a visible gap in between the valve cover and the bottom?

@truckscarsandcoffey3973 2 года назад

Hi Ben. No sure what you mean by "the bottom". But I can tell you there should not be any gaps anywhere. That leads to oil leaks or vacuum leaks, depending on what the part is. Thanks for watching.

@cobrastrikesagain6385 3 года назад

Did you change the intake manifold gaskets

@truckscarsandcoffey3973 3 года назад

No I did not as they looked fine. I just cleaned them off with a bit of parts cleaner and re-used them. Did not hear any leaks so I guess it worked haha

@DreadHeadChannel 2 года назад

3:23 what is that part called I broke mine!!!

@truckscarsandcoffey3973 2 года назад

They're both just vacuum hose nipples

@fn6553 3 года назад

What about the rear valve cover gasket. there has to be a trick to it.

@truckscarsandcoffey3973 3 года назад

I am sure there's a trick but the owner needed to get back home and as they say, if it ain't broke don't fix it.

@joncaldwell2434 3 года назад

@@truckscarsandcoffey3973 what was the hoses you took off the manifold?

@327JohnnySS 2 года назад

You should have told them that you are already there. If the back valve cover fails and makes a misfire they will have to pay twice to have the problem corrected. Short cuts never pay off. Yet the customer is always right? When they tell me how to do my job I just tell them take it somewhere else and good luck. If the easy front is failed the rear is not to far behind. Pay me now and later. Never re-use a gasket unless you enjoy working for free on a come back. It does bite that you have to buy a whole intake gasket set just to replace the upper 1. Yet its only a 15$ difference in getting the whole set as the upper only has to be "special ordered " from the parts store that will take a "few days ". Thank you for the video. 👍

@user-hc9rm4wu6o 4 месяца назад

Of course u ant gonna do that back mtfr that's what I need too see if your front is leaking it won't be long and don't u think your back is gonna be leaking Der Der der

@truckscarsandcoffey3973 4 месяца назад

Are you wrong, no. However I did what I needed too at the time and it's all the owner wanted me to do. You won't be getting a follow up anyway for the back because the car was totaled 3 years ago. Thanks for watching.