VAS5054A VCI teardown. Internals and PCB quality. 

👍👍👍👍👍 Thanks for showing us mate

Good one....i use it often

works amazing good clone vas5054 tool, even as passthru for xentry techstream honda hds, forscan and nissan consult, this one needs a small modification in obd cable or a breakout box to connect pin 1 to 8. so for 50 bucks you get a tool that can handle a bit of work, and in odis is like the original one

13:56 "Hopefully soon you'll see some videos where I'm going to use it" ... well hopefully it still works :) Always nice to see the internals of these knock off interfaces, can be a lottery with them sometimes!

You are lucky! The microcontroller is: SAF-XC161CJ-16F40F The two K6X4016C3F memories are original and work at 5 volts. Super! OKI M6636 is not original, replace it! TJA1054 is not original, replace it! After replacing them, reverse the VD7 diode because it was intentionally soldered incorrectly. Bluetooth is a tree, nothing to do with AMB2300, of course it works, leave it. Separate the boards where the relay is, under it is a suppressor SM6S26A, under it a little to the right I see a 7805, this stabilizer does not fit, get a new one, solder it so that the pins stay as long as possible and bend it down so that it stays with the bevel over the TLC3702C comparator so that the long pins serve for better cooling. Flash memory, Fujitsu 29F160BE-90PFTN is slow, but it works, if I were you, I immediately throw it away and solder AMD AM29F160DB-70EF. I really wanted to see clearly the three chips located next to the relay and the suppressor, but unfortunately your camera did not focus. My conclusion is that if I had come across such a clone from AliExpress, I would have been lucky! Unfortunately the clone they sent me has all the original chips but the board version is a little different and the biggest downside is that the microcontroller is SAF-XC161CS-32F20F, it's without SDLM and runs at 20MHz, that's a lot bad! Now I have to spend a decent amount to buy an original SAF-XC161CJ-16F40F and only then my VAS 5054 A will work. Friends, if you bought VAS 5054 A with SAF-XC161CS-32F20F or SAF-XC167CI-32F20F processor, feel free to discard them or replace the processor with SAF-XC161CS-32F20F, but it requires more than replacement... Good luck to the initiates!

If it’s made in Germany like the cars it is going to be flawless

"Do not use below garage floor or grade level" What kind of warning sticker is that on the back..? Does it have a GPS or something inside?? They managed to cram a lot into that case, very nice!

i thinks its compatible j2534 pass thru , can be used on ids jlr as well , comes with drivers for it

👍

muy buen vídeo nadie muestra los componentes asta hoy en día ya los anuncian ala venta a si yo compre una vas 5054A hace como diez años y el dis que full chip la mía lo trae la estructura del vas es la original son marca softing ag las memorias iguales o mejores que las que trae la vas que esta mostrando y todo lo nuevo que son invenciones nuevas la mía tiene diez años trabajando y trae todos esos componentes y la abrí por curiosidad por que están anunciando ese full chip y la que compre hace años puedo afirmar que esta mejor que la que esta promoviendo y trabaja con odis y no la compre original era clonada por que los software eran dvd y no era originales buen vídeo y saludos desde la ciudad de mexico

Do you have a link? Looks good fancy my chances on that one!

where did you buy it pls?

Any link to buy this vas pls

can you give me the link to buy this tool.

looks similar to a adreno board and hats.

Hello, is this originale or clone? Thank You

This version has been sold out for a while now I had to settle for a lesser variant ..... and I'm pretty sure i messaged you yesterday 😪

Better use with usb cable

The BT module on that PCB is not the good one. Thats just a OKI version

Could you add a link for where you purchased it?

shockingly, theres a circuit board in there, and not say, bees

Fake OKI chip. Fake BT. Low speed RAM. Fake TJA 1054AT. No LTAEF. Fujitsu flash. Fake A5780A