Veteran Sherman-S | Right Wheel Bearing replacement

Подписаться 2,5 тыс.

Просмотров 2,5 тыс.

50% 1

Changing the Right side wheel bearing after 1600km (1000 miles) on my Veteran Sherman-S Electric Unicycle, that was a lot easier than left side, replaced the broken mudguard at the same time, you can also cut the bearing with a Dremel like on the Left bearing video (link under) !
Here's the links for the Bearings
Canada: amzn.to/43BbQV2
US: amzn.to/3Q3L1Wz
See this video which i did both Bearings at once (timelapse) • Veteran Sherman-S Bear...
LEFT SIDE Bearing Replacement video HERE:
• Veteran Sherman-S | Le...
Bearing EXTRACTOR tool: amzn.to/3ONLBqh
------------------------------------------------------------------------------
🔥Buy your EUC here !🔥
Ewheels: www.ewheels.com/?affiliates=725
eevees: eevees.com/?ref=sd7yx3w9
------------------------------------------------------------------------------
🔥Support my Channel (Paypal)🔥 : www.paypal.com/donate?busines...

Авто/Мото

Опубликовано:

10 авг 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 37

@onmywheel 11 месяцев назад

Thanks for the info

@MathieuTechMoto 11 месяцев назад

That's a pleasure :) !

@alehmerv 11 месяцев назад

Hi. Is it important to follow the sequence of disconnecting and attaching the connectors?

@MathieuTechMoto 11 месяцев назад

You want to make sure to disconnect the battery wires first, after that no much worries, but also make sure that the 3 motor wires stay in the same place, they are different lenght anyway

@milordas 6 месяцев назад

Disconnect positive first, then negative, and another battery the same. In reassembly, negative first

@guirob01 11 месяцев назад

Merci pour le vidéo bien détaillé. Combien de km tu as fait avec le 1er set de bearing? Selon toi est ce de l'usure normale ou bien de l'eau s'est infiltré dans le bearing?

@MathieuTechMoto 11 месяцев назад

La roue a 1600km, le bruit a commencé aux alentour de 900km, je suspecte que le fabricant a utilisé une graisse de mauvaise qualité ou potentiellement contaminée, le bearing original n'a pas de lousse, il pourrait être nettoyé/regraissé et réutilisé

@milordas 6 месяцев назад

@@MathieuTechMoto SKF, FAG bearings all the way, better do not use chinese as they are prety lose. Imo C3 bearings not v.good, better is CN (normal)

@davideofrodo 3 месяца назад

When hammering the new bearing onto the machine, does it have to go down as far as possible?

@MathieuTechMoto 3 месяца назад

Yes, you will hear the sound changing when it bottoms out

@luwn00bz 2 месяца назад

Can you explain why the outer shell of the bearing doesn't need to be as tight? You literally pushed it it, why doesn't it need high friction to not lose grip while riding?

@MathieuTechMoto 2 месяца назад

No it was pretty tight

@MunkEUC 3 месяца назад

Can you provide a link for the bearing press you used to hammer in the new bearings?

@MathieuTechMoto 3 месяца назад

Bearing EXTRACTOR tool: amzn.to/3ONLBqh

@MunkEUC 3 месяца назад

@@MathieuTechMoto thank you, but I’m am referring to the press and not the puller.

@MathieuTechMoto 3 месяца назад

@@MunkEUC I did used a hammer to install the bearing and not a press, if you are asking about the socket i had some metal scraps laying around that just happened to fit, you can use your old bearings inner races but you'll need to cut the bearing for that

@KevinRedmondWA 11 месяцев назад

Can you share link / details to the dewalt screw bits that you used?

@MathieuTechMoto 11 месяцев назад

I didn't check each of the sizes because i remember by the eye, screws are pretty standard sized, but i bought them from the dollar store some years ago and they are very solid That's the best i could find on Amazon, this should do the trick amzn.to/3Ousy36

@KevinRedmondWA 11 месяцев назад

@@MathieuTechMoto perfect, thank you! By the way I installed the same seat as you, thank you for making these great videos!!

@milordas 6 месяцев назад

Recommended A4 bolts as they more resistant to salt, water, but A2 would fit too

@zlkr9664 10 месяцев назад

did you get the wheel centered?

@MathieuTechMoto 10 месяцев назад

Mine as always been well centered, dont know why

@skampster 9 месяцев назад

Did your bearing fail because of wet weather riding?

@MathieuTechMoto 9 месяцев назад

Possibly yes but there was not a lot of grease in the bearings, before i installed the new ones i added grease off camera

@milordas 6 месяцев назад

I would recommend marine shaft grease for that.

@MathieuTechMoto 11 месяцев назад

See this video which i did both Bearings at once (timelapse) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-pmP0NmOGCns.html LEFT SIDE Bearing Replacement video HERE: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-M_eyZnjyrkM.html Here's the links for the Bearings Canada: amzn.to/43BbQV2 US: amzn.to/3Q3L1Wz Bearing EXTRACTOR tool: amzn.to/3ONLBqh

@milordas 11 месяцев назад

its easer to replace both at once, lol

@MathieuTechMoto 11 месяцев назад

Of course it is, but you have to take an entire day to do both, that's why on mine i did it in two sections, i was lacking free time, and thanks for watching :)

@MathieuTechMoto 11 месяцев назад

See this video which i did both at once (timelapse) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-pmP0NmOGCns.html

@burbage67 9 месяцев назад

My max is making a grinding and vibration noise and e hall comes up on my screen. Can you help with info? Thanks for the video

@milordas 6 месяцев назад

@@MathieuTechMoto no not entire day, now im stuck at bearing removal, and it will took 3 days lol, as on weekend no shops can offer me bearing removal tool, as the one i had, broken to stuck bearing

@MathieuTechMoto 6 месяцев назад

Yeah mine too almost broke, thats with i cutted the bearing with a dremel, i just had success today removing a customer left bearing from a big ass puller tool borrowed from a friend today, i did remove the bearing seal then heat with heat gun and it came off a lot easier @@milordas