Watch This if you Struggle Regripping Golf Clubs 

I regrip mine and others clubs all the time. Tips are: get a table and a vise. Hook cutter is key. Use precut tape. Might cost more but easier to work with. Practice on an older club before your gamers. Don't skimp on solvent. Many grips have a center line or dot on the them by shaft. I put a Sharpie dot on shaft to help line up next grip. Comes off easy with some solvent. After a few you will get the hang of it.

Some good tips…. Once you get it moving up the club shaft….don’t stop! Run it straight up. Next level item is by looking at the butt of the grip, there is usually words/writing….whether you want logo up…or logo down… try to get those words to go 9 o’clock 3 o’clock orientation . Small amount of the solvent on a paper towel to clean and wipe down the shaft from grip to club head. Make it look clean and professional.

Good job on explaining the process. Thanks for sharing

Great video. Thank you.

Best regripping video!!!

Thanks for the tip👍🏽

BRILLIANT!! the tape tip... thats always been my bug bear😅😅

I would add that when working with graphite shafts you want the hook blade to cut the grip on an angle avoiding the paint on the graphite shaft.

I used compressed air to put my new grips on as you showed in another video... 👍

Don't suppose you could make a vid on how you added glue to the 101Ts please?

Have ever installed a lamkin fingerprint putter grips You don’t need tape and you better load up on solvent cuz it’s a bear to get on If you have tips for that grip install please share

I've never re-gripped a club before but would like to experiment with a few different grips on one of my clubs before deciding what's right for me. My current Callaway grips don't really have an alignment line as such, more an upward and downward 'kind-of' arrow that is part of the grip design, so it is very difficult to see how it is lined up with the club head. Can anyone give me some advice as to how to correctly align the new grips? ie. should the sole of the club be pointing to 12 o'clock and the alignment marks on the new grip be directly in line with the edge of the sole? Thanks in advance for any advice offered.

i like very much your tips about regripping en reshafting but i didnt directly find a answer to my question: when you regrip a club you can align the grip, some grips are especially made for this , but you can also choose to NOT align your grip with the head . now the question : when you reshaft a club : are the shafts especially made to align in a certain way with the head or can you turn the shaft and so create a special pattern : does this work with steel shafts and also with grafite shafts?

I just pulled the grip off my 'new to me' driver.... the used club dealer I bought from uses some very frustrating clear tape that was horrifically sticky AND tore apart! Took me almost an hour picking away at it with the shaft and my hands coated in turps to remove it all 😮‍💨

Recently I had a devil of a time regripping using acetone. It sounds ridiculous, but it seemed like it shrunk the opening of the grip. I went back to mineral spirits and the grips went on easily again.

If I want two wraps of tape do I just peel first layer and place a 2nd on top? How difficult is it when sticky sides meet?

Silly question... Do you not have to take the 2nd side off of the double sided tape facing the grip?

like your vidios can you please tell me where to buy your tape

Can you do a video on building a combo iron set please? I'm looking at mizuno irons and on their site you can basically make a combo out of everything. Anything would help. Been leaning towards the 223s

My tip,,,dont skimp on the solvent!! Almost ruined a 35 dollar Superstroke putter grip because it wasn't wet enough,,luckily I had it nearby and could save it.

I was taught using contact cement, which makes it easy to blow out later; but I like my brain cells.

believe me get a vice and rubber shaft clamp very cheap i can put a whole set of grips on in half an hour craphite shafts if you use aplain blade just roll the old grip up the fhaft i " at a time and cut you wont cut the shaft

What is your opinion on using soapy water instead of solvent? I tried it once and it came loose when I played my next round. I don't have a vise and I have changed my old set. Lot of good tips!!🏌‍♂⛳