WINKFP FLASH PROGRAMMING E60 MODULES Part 4 8-7-2015 4:34:11 PM 

Certain parts such as the Instrument Cluster, EWS, CAS, DME, LM, ZGM, FEM, etc., contain mileage data. Driving vehicles with such swapped parts may result in mileage corruption, and therefore must not be used. The CCC/CIC Headunit, MASK, CHAMP2, RADIO2 or Headunit-High has enabling codes for certain features, e.g., satellite radio. If a feature is already enabled, but sees a different VIN on the bus system during power-up of the module, it cancels the code automatically. When an enabling code is canceled, it is not reusable. The only way to enable the feature again is to either contact Technical Service or replace the control unit at your own cost. Therefore, swapping these types of parts on E-Series vehicles is not recommended.

Diagnosebimmer12@gmail.com Call me to install and program yours today in Miami , bro-ward, Kendal ccc/m-ask, Top hifi Amplifier, CAS unit Programmed & Encoded. 786-355-3660

Hey .. I need your help .. I had water leak that fried my control box for self level suspension E60 wagon ... how can I reset to factory height after replacing the control box? it is sitting low now

Hello there I could not run the winkfp program. I opened the program. Comfort mode then zubs update. Nothing seems to happen. What is the reason ? help me please

Is it worth it to update these modules if they haven't been updated since the car was manufactured? Or is the risk greater than the reward?

so.. is there next part? could not find it, its interesting how did the story end

hi, can u please assist with flashing that went wrong on a e60 .

Nice post ,I have updated my e66 2006 daten files in my laptop, how can I update car's software? Ho I have to use the same approach you following with WinKFP in this video? Thanks in advance...

Hi mate great video! Flashed my E70 and everything went just fine until last module ZBE wich is locked in programming abort. Flashed with V66 over Dcan cable. Is there any chance of recover the module? Inpa shows status Ok but also error 12 programming abort. Tried emergency flash in Winkfp but ended up with signature error..... can you advise please

Can you leave a d/load link to ISTA-D ISTA-P and the loader thanks.

I tried listening to what you were saying but seemed like it was Eminem rapping

which module updates idrive ccc

I have BMW E60 525i and trying to update DME/DDE and when I enter ZB number it won't recognize it. I was able to update some other ones, but can't seem to get the DME/DDE for my car. My Car jerks and it seem like updating transmission software will stop the jerk. Thank you.

Recently i tried to update my car with little experience using sss, during the process i was asked to turn off terminal 15 (shut of ignition) and i fail to do that process so i continued. Now my interior electrical components wont operate and i was told my car was on bone state. I can turn it on and drive but the lights stay on so it drains battery, car wont lock, seats wont move, and worst of all i try to establish a connection with the car and it fails to communicate i cant even read code with inpa, i cant access

Hi i followed your instructions and when i upgraded the szl module i got an active steering error which wont clear after restart. Could you please help? Thanks

I'm modulo blocked BMW X5 2003 (DME 7 522 800), with the update would unlock?

Can I use WinKFP while engine running? Or only press start without holding the break pedal?

Hi, could you help me, believe damage my car, kind flashing the modules, now the cat is completely with errors, please help me

u do support with teamviewer ?

I replaced the M-ask unit on 2006 E60 after my original went dead. I got an error on the display saying Head unit is not programmed properly, I configured my winxp Machine to run INPA, DIS, PROGMAN, WINKFP. Using extracted files from Progman I was able to configure WINKFP. All works except progman tells me I need an OPP ICOM cable. In INPA UIF I have ZB numbers from the MOSTGW, MMI/CCC, VIRTSG90, and VIRTSG91 and the all have the incorrect vin numbers. So when I use WINKFP to Enter the ZUSB I get an error 704 Error determining ZB number check assembly file. then it reads something like sg.fam DAT. Can you tell me if I incorrectly configured WINKFP or is there some steps I am missing to complete the updates. I only have a USB OBD cable so I want to proceed very careful as not to ruin my car. Any advice you could offer would be great.

i appreciate the effort but god dam you need a better mic, its so low.

Don't give him any money. I paid him for ISTA and it doesn't work, now he refuses to do a refund. He's a scammer.

call 786 355 3660

Call 786-355-3660 / Diagnosebimmer12@gmail.com for ISTAD & ISTAP Software.