Wiring Speakons to an iNuke or Other Pro Amp 

Thank you sir. Very informative and easy to follow.

Great video Ryan.

This helped me a lot. I have the nx3000 and wondering how to bridge.

Dude amazing video lol seems like this didn’t exist:).

Very thorough video. Was unfamiliar with Speakon connectors so this was a great introduction, thanks !

thanks for sharing this video on how to bridge these amps with the Speakon connectors

Sir amp side spekcon bridge mode 1+ 2+ but speker side spekcon conaction in bridge mode (wire amp side 1+ 2+. And speker side _____)

Fantastic explanation thanks

i still have no idea how to connect the bridge mode to my subwoofer, i mean i have 2 voice coils on my sub, 2x2 ohm, which should be 4 ohm when i bridge it on a normal amp, which would be simple, but with this speakon shit i dont get it at all

I have a custom cable that goes from speakon to Jack. I want to run this power amp to a load box then using the line out of the load box for entering into a cabinet simulator. May work right? Using just one channel in mono. Guitar guy here...

The terminal screws are not phillips, they are Pozidrive #1. While phillips will work, closer observation reveals the Pozi drive has additional tooling details that fit more securely in the tiny terminal screws that are easily damaged if overtightened or tightened with improper tooling. Neutrik (speakOn's manufacturer) has tons of wiring info and product info. Oh, and the other parts that screw on to the plug are "strain relief" which prevent strain on the screw connections which prevents them from pulling out when some moron pulls the connector out by the cable.

Very helpful good video. Thanks

Few years later, Thanks :)

Is guitar center a good place to buy pro audio power amplifiers would you ever recommend going to guitar center when it comes to shopping for pro audio power amplifiers

If you run 4 1000 watt power amplifiers on a single wall outlet that is on a 15 amp circuit breaker will the circuit breaker trip.

Will 6 behringer inuke nu3000 power amplifiers on one outlet cause the lights to dim on heavy bass notes

If you were to run pa speakers directly off of a av receiver without a pro audio power amplifier would the pa speakers not be as loud.

Are speakon cables and powercon cables not interchangeable.

hello ! can i bridge inuke 3000 with an nl2fx connector??

Can you help wiring a speakon connector for a crown xls 2002 amp in bridge mode. It reads for bridge mode: [ Pin 1+, 1-, 2+, 2- ] Amp end gets what connected? Subwoofer end gets what connected? Thank you

Is bare speaker wire obsolete and hardly ever used in PA systems

Is a really good quality mixing console required to properly use pro audio power amplifier so that it can get loud

Hi I was wondering if you can help me out I don’t k ow how to hook up my inuke 3000 amp to my tv and my speakers?

Can you post a link to where you got your wire and Speakon connectors especially the wiring please 🙏🏾

Can you help me with bridging a inuke nu4-6000? I'm a bit confused

im buying the 1k version and the dayton ultimax 2ohm dual coil how would i wire up to my home receiver and to my sub?

man this is so confusing what cable would u need if u wanted to daisy chain 4 speakers to 2 ohms each channel

what cable are you using

can I use this amp on my home theater, how would I connect to speakers?

In Mono Bridge Mode using 2 conductor at the 1+ , 2+ conductors, are connectors at speakers left wired the same with no changes? Are they just jumped from one sub to the other with no modifications? I am curious because I dont know if the input jack on speakers will be ready to accept this wiring change...

Thank you. Made things very simple for us visual learners.

Can speakers put out more spl than what is stated in the speakers owners manual if you use a really good power amplifier to power your speakers and if the speakers are in a properly tuned enclosure like for an example if the owners manual for a speaker says it has a maximum spl of 90 db can it read 123 db on a spl meter if it’s powered by a really good power amplifier and if the enclosure for the speaker is tuned properly

Does hooking up a active crossover and a graphic equalizer to a power amplifier make the subwoofers or speakers louder.

Hi Impulse Audio, my amplifier is +2 -2 connection but my speaker is +1 -1 how should approach is?

Hi, great video! One information is missing for me though. Can I use build in crossover in bridged mode? Let's say I just want one subwoofer in bridge (4ohm 1200W) Manual says that sub should go into B out on LPF.

Hello! thanks for the video it was really helpful! However, I want to connect a 4ohm sub to the inuke 3000(non dsp) in bridged mode ... it seems that the built-in crossover is not working in bridged, is this correct? do I need to buy an external active crossover tu cut the HF before the inuke? Read a lot of posts around there with people connecting subs in bridge mode but no body is talking about using an external crossover. Thank you in advance!

I found out that some power amplifiers have a switch that says ground lift what does that switch do

Hello, I would ask for a Little help in here. I own one amp like yours and I want to use it with 2 Behringer vp1800s subwoofers, so I have to switch it in The LF mode but It only works in stereo switch, would that be because my speakon connectors has 2 poles?, if I use a four poles speakon can I connect it to one of The Subs and then in parallel connect it from this sub to The other one?, and it would ne in mono mode switch? Thanks In advance!

Does this work with 240V power supply? also does this have a XLR input? I could see only speakon input.

May be a stupid question, but is it fine to wire a bridged mono cable using a 4-pole speakon on the amp side (+1 & +2) and use regular banana plugs on the passive subwoofer end?

can i use this amp to hook up my normal amp and run my cerwin vega xls-215 speakers

Can you use electric guitar amplifier cables as speaker cables for a power amplifier

Curious what gauge is that 4 conductor speaker wire, also where did you source it from?

i know this. I don't get, witch signal goes to the tweeter and witch to the woofer of the speaker...?

May thanks

Wow that was fast, Thank you very much. The thing is that If I switch The amp to The LF (low mode) I understand that it will only work one of The outputs A or B I can't remember, but if its not The case and both channels are working with The low frequencies I can use it in Stereo, would that sounds correct to you?

I am running Bridge mode into an Ultimax 15 with DVC. Will you please check my math because after your video stop, my confusion starts. I will wire the sub in series giving me a 4 Ohm load. After I wire the Inuke OUT with the 4-pole connector 1+ 2+, how do I wire the other end? I presume 1+ 2+. Then the Female socket would be wired 1+ 2+ to the sub voice coils?

Thanks for the video! Really helped, when using it in bridge mode do I have to input mono in both channels or can I just input mono in channel a? I'm thinking about buying this amp and I would like to know if I have to make an xlr Y splitter for it, apologies for my crappy English...

What can I use to hook rca male cable subwoofer to the TRS input conncector??

Can you hook up a pro audio power amplifier to 1/4 inch audio output jacks that are already amplified

can i go with 2 full range speakers to 1 ch and sub on the other ?? Plz any answer to me ?

Hello, I have the nu3000 but can't figure out how to work the bi-amp feature. Do I need 4 pole and 2 pole cables or what, I just need help

Sir I have single 18'' 1200watt 8ohm bass and amp inuke 3000 plz info me how play on this amp

hello, we just got an inuke nu4-6000. we tried to run all 4 channels, and it doesnt work correctly, any ideas? thanks