You’ll Never Weld Pipes The Boring Way Again | Metalworking Project 

✨✨✨ Check out our other video HERE: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-efL3A4_8UJM.html

Tack welds on a butt joint = zero penetration. And then ground off completely flat. Lol the only thing holding that together is the black paint! 👍

Clever way of cutting metal to make bends, but if you want any strength in your welds, you need to grind a valley channel into the weld points. Then, with the welder, fill the valleys with weld, making sure the welder is set to proper amperage and voltage for gauge of metal you’re working with. What you’re doing is making superficial surface tack welds, then grinding them down, leaving behind next to nothing. These would be fine for cheap IKEA desks, but I wouldn’t use these for anything heavy! Still liking the video simply for showing the cutting techniques.

"a grinder and paint...makes me the welder i ain't"

Love the way he always moves the ruler to measure 1.5cm instead of just putting a mark at 1.5 and 3 and 4.5cm lol

Entertaining. It should come with a disclaimer that those spot welds on the tubes are not suitable for metalwork requiring strength due to low penetration.

When you wanted welding lessons, but your parents got you a laptop and editing software.

For the love of God JUST RUN A BEAD!! These spot welders will drive ya nuts!

I've been in factory work for almost 30 years now and knew tons of welders, sheet metal, and machinists journeymen over the years while I was setting tools and dies. I should have taken welding up. I had plenty of guys that would have trained me and I love it.

To all the naysayers, use the geometric patterns and make the proper welds. I believe that’s the point of the video anyway…not how structurally sound the end product is. Personally I think the patterns used for the fabrication is awesome.

I watch these videos to learn from both the video itself and also the many many comments. Always appreciate the useful stuff and also learn from the mistakes. Thanks to everyone both the video maker and the people who commented.

Wonderful cutting, grinding and painting tutorial ✌️

Wonderful grinding and painting tutorial!

What I do like is how accurate the cutting is with the grinder. No fluctuation of the marked line.

The grinder covers up bad welds and the paint covers grinding marks

So let's see: grind away the strength of my poor quality weld and throw some paint on it. Got it 👍

I will still be doing it the boring way thanks!

When you want something that looks pretty in a short amount of time but don’t care if it breaks…

Not one pipe was hurt during the making of this video. Still nice to watch.

Structural integrity has left the chat

Some epic video editing and camera work here. This video must have taken many hours to make.

Very precise with that grinder.

Interesting aesthetics.

Good luck getting those joints to pass any kind of certification!

I love when people square cut and surface weld, then grind off all of the reinforcement so it looks machine finished. Then act like that was all acceptable.

This is the basic bro equivalent of makeup/home deco videos.

My first job in sales took me to Hobart in London Ontario and when we were done business the guy offered to give me a try at arc welding in their classroom. There I am in my three piece business suit, put down my briefcase, don the visor and pick up a torch to lay a bead. It was wire fed. Later in life I would have liked my own oxy-acetylene setup because for what I wanted to fabricate it is more suitable.

If you're going to grind down the welds at least weld it right. The way you are showing has no structural value. I fabricate rescue baskets and other load bearing devices and your welding would not pass weight testing and would be dangerous in certain applications.

I weld pipe all day long..everyday and my breaks off the trigger are shorter than this guy's welding runs.

I don't know the 1st thing about welding yet I enjoyed watching this..

Some serious grinding skills!

Guys, its the Editing. Im 95% Sure for that wall thickness the welds hold up like they should

Great ideas for coat hangers, 👌 Thank you.

That's very smart. Thanks for the tips.

thanks, you made my day sir

Looks visually impressive but I am not sure about the integrity of the welds

That welding is holding together nothing

After commenting and reading the comments which were critical on the strength of the weld after grinding off, I revisited the video and I found that there were sufficient gap in the joints for the tack welds to penetrate to give stronger joints than I thought; even if the joint is ground to the surface. Like me I invite others to relook at the video.

Pleasant to watch esthetically speaking but from a mechanical point of view, there is no way this type of welding allows deep and strong fusion.

The only thing holding the metal together are gypsy prayers😂

To all the welders here, I've been a welder since '99 and yes, this guy's welding isn't up to standard. However this video is about being creative with steel. These hacks he's showing is for decorational purposes. Such as a frame for a coffee table or a coat hanger. However, when this guy is using those spot-welds to fabricate tools which need to apply a certain amount of force he's a danger to himself.

The first 'related video' below this one is "Busting Fake Welds" 😂😂😂

Vidonun başında öğrendiklerimden sonra,örnek uzay gemisi bekliyordum.Sadece askı ve raf!.

You can actually see the joint after grinding all those tack welds off it’s cool and all but kinda bad info for anyone watching this new to welding or looking to learn

Love this channel

I will do whatever I want and nothing and no one can stop me. Not even some clickbait title.

I don't know why I'm watching this 😂 but it's pretty impressive

Waiting for the pipe welds..

He is the real IRON MAN!!!

If you're going to make those light tack welds, at least run a nice hot bead down the inside corner

"Grinder and paint makes me the welder ain't!" -A very wise man

That’s cute, apply the weld in spot welding method then grind it all off. Spot style mig has little penetration but it looks better on videos, also most arm chair experts struggle to do a continuous mig run. Just sayin!!!

Truly you are the best I have ever seen..I wish to learn

SHOW DE BOLA. PARABÉNS

Fascinating art

Класс! Перед тем, как сваривать, края металла профильной трубы лучше забить молотком немного внутрь -при зачистке не будет сниматься большая часть сварного шва, так как он будет почти весь внутри. А так всё класс.

I liked it, appreciate your skill, good work. thanks for your efforts.

Those welds aren't very strong

What a great way to not weld.

Love the quality of your videos 😊

I’m not a welder but is magic going to hold that tack welding together? Or is it video editing that will? I don’t think welding is boring. I don’t even find soldering wires boring. Even aluminum brazing is enjoyable.

Mom I wanted welding lessons…. We got welding lessons at home.

The fact that in the first minute they, instead of, I don't know, using a rule properly. They instead decided that the best way to measure out the distances correctly was to move the rule to the new marking instead of just marking the it using what's already on the rule baffles me...

If the application is furniture of something like that, what's the problem with the welds? Appreciate the creativity this can stimulate in someone ambitious to try.

Nicely done

A grinder and paint makes the welder he ain't.

Very nice 😊

Some cool project ideas here!

Очень красивая работа 👁👏

I'm just happy you're measuring in cm and not in inches.

Top demais 👏🏿🙏🏿👨🏿‍🏭🇧🇷

Nicely work

And it's because of welds like these your patio furniture doesn't last long.

Hey man this was a cool video with some great looking end results

Wouldn’t even call this welding. This is tacking, and is definitely not structurally sound.

Great job due!

I’m going to a meeting tomorrow about welding and painting I have 0% experience on this but I learn very fast.

Maestro gracias por compartir saludos

looks good

Let this man build the roll cage for your Honda Civic!

Very impressive~!

I keep waiting for my balloon dog, but it's just pipes...

Very accurate cuts and templates.

I'm impressed not weding but grinding

This entire video has the soundtrack of what 50 Cent would say yes to and put on his album.

Thank you. That was so satisfying to look at your work. I appreciate for the ideas and inspiration.

Awesome stuff!

Nice work

Bravissimo!

Exelente video

Oh wow! I will try it in home. I❤️❤️❤️this vid. 👍👍👍👍👍👍👍👍👍👍

Very nice work and videos

This guy is much better at cutting metal than he is at welding it.

very very good

Awsome..

Nice video editing! Could we see it without the dropped frames though?

Easy for installing an LED light bar!

Any chance you can do this same kind of video for 2” circular steel pipe. Lol

The cutting of the joints and fit up are pretty decent ideas, but for me as a professional welder, seeing them being joined by stacking tacks simply is flabbergasting. Those joints have zero penetration and would likely break if you dropped the part. Not even close to quality or reliable welds.

Dude you’re NICE 👍🏽