p17 is Cruise mode you said if you want cruise set it to 1 and if you want cruise set it to 0. that was a confusing bit? how does the cruise control work please? kind regards.
I managad to figured that out myself it took me a while , 1. turn the scooter on and enter the password you have so it will go into the on state. 2. hold power button and mode button together (you'll get a popup for a password) 3. enter "1111" 4. it will ask for a password again this time enter "0000" 5. this will now make your scooter without password and should allow you to turn it on and off without pass. if you need help go ahead and PM me,i can always make a video if needed.
someone had a problem error 09 (contoller) in his lcd for his scooter, What is the problem ? how to resolve it or réinitializing it please ? he can not use it now same scooter was dammaged
Riding motorcycles for decades I was shocked how un stable this machine is. Anything that goes over 15kph should have some sort of stability. On this machine, if you scratch your nose with one hand while you are cruising at 60kph, you will crash. I demonstrated this at 40kph. On a motorcycle the steering geometry is such that its trail ensures hands off stability. These cheap Chinese powerful scooters have no regard for personal safety which could be remedied with a slight design change.
Hey please help me, i have the zero 10x and Under the cable shield in the handlebars there is a wire inside which there are 3 wires inside of him: red, green and black and they were wrapped in white tape in a bad way so I wanted to replace the tape and then suddenly the scooter stopped working and did not open again... please tell me what to do if you .
Hey, how can i find out what my cut off is? Like when my voltage gets too low, i believe it cuts off when the battery reaches a certain percentage. Anyone know how to check that? Thanks in advance.
go in to the p menue and volt on my scooter not zero i can adjust the cut off higher and when it cuts i have spare power to take me home like a reserve fuel tank WARNING don adjust it lower you wil have more range yes but it can damage the battery
@@CarleyEspritPhilip Yah, mine was aet at 42 and the actual cut off i believe it 41, or maybe 40, u could google it to be sure, but mine is a 52 volt, and the cut off is at 42. Have fun and ride safe!!
Can anyone help me. I got this LCD and controller. I got 3 modes. But I need to start slowly. Why is it not possible to change speed? Why is is only 3 speed settings? It makes no sense.
Does electronic braking on this actually work? I didn’t see any difference when I tested it up on the chair so the wheels can freely move and I didn’t notice any difference after letting go of acceleration whether electronic braking actually works, I went through level 1 to 5 in P11 and didn’t see any difference
Ahh I can confirm it does work. Once you get up to higher speeds and you pull the brake lever lightly the regen brake kicks in and you can hear the motor whine
I've had send the following:: P01: Backlight brightness, level 1 is the darkest, level 3 is the brightest; P01 defaults to 2 P02: mileage unit, 0: KM; 1: MILE; P02 defaults to 0 P03: Voltage level: P03 defaults to 60V P04: Sleep time: 0, do not sleep; other numbers are sleep time, range: 1-60; unit minutes P04 default is: 10 P05: Boost gear: 0: 3 gear mode; P05 defaults to 0 P06: Wheel diameter: unit, inch; precision: 0.1; P06 default is 11 P07: Speed measuring magnet number: range: 0-255; P07 default is 30 P08: Speed limit: Range 0-100km / h, P08 defaults to 100 P09: Zero start, non-zero start settings, 0: zero start; 1: non-zero start; P09 defaults to 0 P10: Drive mode setting 0: Power-assisted drive (The power-assisted gear determines how much power is output. The handle is invalid). 1: Electric drive (drive through the knob, the power assist position is invalid at this time). 2: The power drive and the electric drive coexist at the same time (the electric drive is invalid in the zero-start state). P10 defaults to 2 P11: Boost sensitivity setting P11 defaults to 3 P12: Boost start strength setting P12 defaults to 3 P13: Type setting of power magnetic disk P13 defaults to 12 P14: Controller current limit value setting Range: 1-20A P14 defaults to 12 P15: controller undervoltage value P15 defaults to 49 P16: ODO clear setting Long press the plus button for 5 seconds, ODO clear P16 default is 0 P17: 0: Disable cruise, 1: Enable cruise; Auto cruise is optional (only valid for No. 2 protocol) P17 defaults to 0 P18: display speed proportional adjustment Range: 50% ~ 150%, P18 defaults to 100 P19: 0 gear enable bit, 0: with 0 gear, 1: without 0 gear P19 defaults to 1 P20: 0: No. 2 protocol 1: 5S protocol 2: standby 3: standby P20 defaults to 0 So the P11 is regen brake or something else?
Can you explain what p18 does? When I got my mx60 my settings were different..p18 only went upto 100. It is possible that I accidentally programmed my LCD controller for a different scooter? All my settings have changed. Is there a way to change it back?
Thanks for the heads up! One question when my scooter is under load the battery shows it near empty, when I release the throttle it climbs back up? Is this normal?
i can tell u that mate! when u use the throttle at 30 % battery it shows you, if u hold this acceleration u get this far . but if you now take your throttle at 70% it shows you how long u can get at 70% throttle, sorry for my bad english !!
@@husse843 Translation 3 years later = If you hold your acceleration at 100% the voltage will drop as your sucking more juice and will show you how far you can travel at 100% throttle. If you hold it at 50% throttle instead of 100%, it’ll change and calculate the new distance you can travel based upon power consumption being used from pulling down on the throttle. Lighter throttle = less juice being sucked out = more distance available to travel before battery dies.
@@modzmetropolis9558 actually there are no calculations or anything fancy, the reason the bars drop is because they are based on current voltage if you are using the throttle you are putting load which drops the voltage
How to get my zero10x taillights standby? If I hold the mode button to turn on the lights. It lights the front only. Back light works if I just press the breaks.
Does anyone know if the QS-S4 LCD throttle unit for this Zero 10X scooter will be compatible with Mototec Thor 60V scooter? I am looking for a spare QS-S4 for my Mototec scooter and they are sold out everywhere.
hi tnx for the guide. when i in the settings menu (p-settings) , and i long press the power button, the "A" in the bottom line changes to "D". do you know what is the purpose of this mode A/D ?
hello. I have an electric scooter and it has the same display, or is it very similar. I would like to know if you could help me with a question that I have. Today when I was going to work, the scooter lost power, but when I stopped, I saw that the display and the ignition were still on, but the accelerator did not work. So I turned everything off, and turned the contact back on, but when I went to turn on the display, it doesn't respond. then at home, I was able to see and verify that the current reaches the display connector perfectly. . Is it sure that the display will be the problem? I also see that there are many models that are the same or very similar on the outside, how can I know if it will work on my scooter? Thank you
@@FalconpevSg Thats the big problem,. since I bought it in AliExpress, and then the store stopped selling in AliExpress, so I can't use the same store that I bought the scooter.. So... if I buy one with 6 pins, and I review the cables, each one in its color... it won't work? thank you
I brought a this set controller but when I connect the wires( only battery wire and 3 phase wires ) "warning sign" blink and when accelator is increased "countinous speed " signs appears, any one can help me please.
Hi, i have a question, when i enter the P settings and long push the on/off button, the letter ''A'' on the bottom left changes to the letter ''d'' And I wondered what it does... so if you know please tell me :)
How can i see the remaining voltage in the display? The bars are not accurate. ¿Cómo se puede ver en el display el voltaje restante de la batería? Las barritas no son nada exactos.
I know this been so long ago.. Can ask why my scooter battery guide is allways 100% I mean full green bar but . I'm driving then suddenly batery empty..
New batch of zero8v2? What should be default number of magnets? Based on the video it should be 30 but i receive it 28 only please confirm which is correct
i need a video on how to put a electric voltage monitor on this lcd ...you already have one for the older 8 but i have the newer 8 with this controller
What do to if the charger light don't turn from red to green even though the step is fully charged (i can see that on my screen and my voltage is 65. I have a 60V). Can it do damage to my battery? Thanks!
Sir may i ask i have a problem with my parameter, the battery indicator is blinking into a lowbat but the volt is 41v, i charge its only 3 hours then the light indicator on charger is green, but still the icon of battery is still blinking,but the scooter is working and running, i want to send a video to you but cannot here, please help me thank you.
2 years ago I remember I was able to turn on "6kmh cruise" mode for my Zero 10X by pressing and holding some buttons. It was very useful when walking and pushing the scooter, but I don't remember how exactly I enabled it. Do you have any information how to enable this walking cruise mode?
I messed with the programming stuff and i almost died on it. Is there any way to reset it to factory settings or something? Scooter wouldnt stop and brakes are really violent. Please help!!!
Hi falcon I really hope you can help me as my vendor isn't being very helpful :( So I bought a mercane mx60. I tried to unlock the full speed and I believe I made a mistake as the settings are different now. P18 only used to go to 100, now it goes to 150. I am wondering. Could I have accidentally programmed it for a different scooter? Althought I have changed the speeds it feels slower and more sluggish than when I first got it and the speed (p8) was set to 35 :( Also, sometimes when I turn it on or press buttons I get a red exclamation! And a "e" comes up then goes away. Sometimes I set the settings and they will change on their own. It is a really heavy scooter and now it barely moves in single motor Please if anyone can help I would really appreciate it. Thank you
Please help I brought my 10x from you guys So happy!! I had a full charge on the scooter and completed a 4 mile ride and then turned it off. I returned later the same day and turned the scooter on to find the battery Barr apparently was empty and was flashing with the red warning triangle next to it.. Thank you.
Hi quick question when you are configuring the P settings menu right above the battery signal there is a letter A but when you hold the power button for a few seconds it switches to the letter d. Can you explain what is the diff between A and d ? Thanks
@@anthonynolan2024 Figured it out. D setting’s function is to decrease the numbers unlike P setting which adds the number each time you press the button.
After you change the settings, does it automatically save or you have to readjust every time? I didn't see a save feature after you exit the settings menu at the end. Thank you for the informative video!
What exactly does the high beam symbol do when hold mode button ? Is there a cable from the controller that is switched on ? If , what color and voltage ? Thx
Thanks for this video! When I try to get the P program menu it goes to a menu PO from there I can’t access to the program menu! Its posible that my scooter has that menu locked?
when i enter programming mode i get an S0 message and it asks me to input a 4 digit code. any ideas what is the default code? help would be appreciated
