You don’t have to be great to get started but you have to get started to be great. Join us for Car projects, house projects, shenanigans, and more! Or Check out our Gaming Channel for a place to have Fun! ru-vid.com/show-UCYSP2Ncl4e54lvqgL0lRh6g
I really had to do something about mine recently and since my pockets were way more empty than I want I've started to think about it and decided to experiment a 7 steps women nails file found at the dollar store. 😂😂😂😂😂me laughing about myself 😮and then followed the steps and did a great job using a bit of water. 🎉💦 🥳🥳🥳 total cost 10$ and still have some unwrapped left.
Instead of removing the wheel well splash guard, it is easier to loosen the motor mount bolts and jack up the passenger side of the engine with a piece of 2x4 to distribute the load across the oil pan. This gives you access to the hardware that is hard to reach.
Great video. The restoration kits actually remove the crazed surface. The basic 3M restoration kit includes two prepackaged clear coat wipes to finish with.
Lemon juice and baking soda does the trick. I threw a good chunk of baking soda in a bowl added lemon juice let it bubble up and dabbed a kitchen sponge in and rubbed in circular motions. You will notice a difference in seconds. Rinse the sponge off and wipe the headlight again with water dry with kitchen towel or a cloth and job done.
the reason you had orange peel on the color base is because you had your air pressure dialed a little too high. just kidding. its because you painted outdoors. you did great!
Sorry you wasted so much time and effort. What you did with all that time I could have done in less than 5 minutes. Guaranteed or your money back. Next experiment, grab a can of repel mesquito spray, not off, spray on headlamp liberally, let set approximately 30 seconds, watch it and you will see the crud running down headlamp. Wash immediately with hot soapy water. Repeat as necessary. Should be able to do 1 headlamp in 3 to 4 minutes. Prove me right or Prove me wrong. It's cheap and fast.
I’m so confused. Is it just dirty headlights?? I used Mr. Clean Clean Freak spray and a power drill brush attachment to clean my headlights. Took about 60 seconds per light to get the dirt off. Why didn’t you use the brush on all the other products like the baking soda?
I don’t need a lesson about Tesla, I know the elite is fucking up everything for poor people and the planet and humans in general. If you were for real you would present it and sell it no need for bullshit
You haven't use the best yet. I just did my headlights. They went from yellow to crystal clear in just a few effortless minutes and for less than $10. You will not get a better result. Use Mother's Mag and Aluminum polisher. Coat the headlamp with the paste. Buff it out by hand with a cloth right away. Stand there in admiration and say, "Holy s*hit". Wash with soap and water. Rinse with clean water and let it dry. Repeat again if needed. It doesn't get any easier than that. To protect the headlamps against yellowing I'm using High Gloss Car Rep 2K Clear Coat spray can. It's UV and chip protectant.
@@rebeccabryant5542 Rebecca. I just did this a few days ago. When I wrote this I had only cleaned the headlights, but not protected them. I recommend NOT using the 2K protectant. Although it protects against UV and premature yellowing, it didn't spray on the headlights properly. It left them looking frosted and not crystal clear. Its not an issue for me because it didnt affect the amount of light coming out of the headlights, but you may not like the slight frosted look. You may want to research a different approach.
If you do get results polishing, you should immediately clean it to remove any residue and chemicals and spray on a coat of the best automotive clear coat you can buy.
I have tried all these remedies and inexpensive kits from stores..And they all work to some extent but after you clean “Spray some clear coat on the finished headlight or it will film/fog over again” make sure you tape around the headlights so not to get any cleaners or clear coat on the car itself.Or if you just ❤️ your car like my Honda’s (pilot/fit) buy new ones 😉
Nice thoroughly explained video, on the two bottom back lower bolts you can get to from top with ratcheting 12 and patience…and very back hidden bolt can be removed with a 12mm deep socket no extension
So why does the manufacturers last so long? Say 3-4 year's why does a good scratching only last up to say 6 mos.? Does anyone consider using a torch to heat the plastic to diffuse the molecules, or is that a thing?
I can see we think a like 😉, the LS fits quite nicely. I’m guessing a Hemi would as well. This guy actually makes CAN-BUS conversations kits for the for the GM computer to talk to the Jeep dash and cluster. I think the Holley modules as well
@@CrookedMustache . I have seen LS swaps, and 345 Hemi swaps, but I am considering an I-6 swap. If you ever have a 3.7L PowerTech out of the body please post the dimensions. You would help the community greatly.
Tke the upper ball joint nut loose first then hit the knuckle to pop the stud out of the knuckle .Then take lower loose then tie rod ends then axle nut and pull the knuckle with the hub off all together. Then press out the lower ball joint,
I test drove a used 2021 Corolla SE and I have to say, the CVT felt like a traditional automatic transmission, even the fake shifting with the paddles was a bit of fun ngl 😅
Yes exactly, that’s what I think a lot of people miss, the CVT here is an alternative to a dual clutch setup. The way this thing shifts compared to the same year Camry was night and Day. And It’s not like the cvts in Nissans that just sit at one RPM when you step on it while the car is accelerating
🤣 Dude it’s the Brits I tell you, I’ve been watching The OG Top Gear since it way back when it was on Discovery Channel, I blame them and “Are you being served” for that ⬆️ and every time I’ve said “lift” 🛗 instead of “Elevator”
@@CrookedMustache Seems like something that "lifts" wouldn't be called an elevator , or a lift. It is a "lifter". Just like something that trails behind your vehicle , is a trailer, someone that loves, lover, one that bakes, baker, something that alternates, alternater , pistons ... oops
I noticed a rub mark on the injector wire when you unplugged it i hope that wasn't your problem, making it show a bad injector but any way grate job and video,,iam going to do the same soon. How has those parts seem to be holding up ever one say ford only with deep pockets ,, 👍👍
Right around the 18:00 mark, nope definitely there before, this was and Dept of Agriculture work truck purchased from an auction. Someone’s been in there before. Clear signs this thing has seen its fair share of service. For 300k miles it doesn’t look bad, on the passenger side bank I could tell one other injector had already been done.
Your better off buying the eBay exhaust builders kit there 90 dollars and have enough pipe to make a turbo kit or enough to make a few exhaust systems that are pre bent as well just a heads up plus they're slip fit