Good video, easy to follow along. My problem, however must've been a little deeper than the regulator o-ring itself. Had to send it into Edgun for troubleshoot and repair. ❤ will save video and keep for future reference. Think I will upgrade to Huma air regulator with a gauge. ASAP 😊
DOPE gun....its on my Hit LIST!! Shiieeet...you really don't need another PCP...this does it all man forreal. Love the Video brotha....subscribed...god bless.
FYI, I realized that my valve slightly went out from this plastic part (like 1.5mm), I've pushed it back into the plastic - as of now its not falling off, but I'm not sure if that fact means its already broken and will have to be replaced. Of course the reason it happened was most likely I had hammer string set too high - as I was not aware you could do it. I was trying to increase it and measure searching for peak velocity but before I get there I experienced a problem as gun fired on its own as soon as I closed the cocking handle. Fortunately it was pointing already in safe direction (not so much for the chrono that get shot with 31gr slug at 277 m/s or 810fps). What happened is that this lever that cocks the hammmer spring by sliding on the handle skewed and was not traveling hammer spring enough back to lock it onto trigger mechanism. As soon as I closed the gun it was going off - fully replicable. I've ordered that peace for replacement and also opened up the gun to see if there are any other damages. So, that pin of the valve moved slightly out of its sitting and that also caused it scratching/pinching the port in which the hammer is travelling. As I understand this is most likely only cosmetic damage as it doesn't have to be sealed etc. Its just the hammer flying and slamming the valve. Still approx 0.5-1mm dent is there now. I'm a bit worried now how much hammer spring is too much. I went back to 0 setting (all in) and started from +5 and went up to 15 and still no peak and I'm worried to try even harder. I tuned the reg for approx. 140-155 bar - not sure how much transfer port allows to travel before becoming a chocke point - but typically most PCPs will allow you to go 160-180 before that becomes a problem. I'm trying to push 31gr .25 HN Grizzly slugs at 920-980fps. I don't have regulator measurments, I assumed the default setting was 130bar (its a reg without any markings, so one of the old ones/first, but hammer is with re-designed shape). I tried with default reg settings (assumed 130bar) and was increasing hammer waiting for the peak. I managed to get just slightly below 820fps without any peak and the gun started to shoot itself. I don't know how many click it was. I decided to try with higher bars, like eyeballed it to 145-155bar via turning it 90 degrees and then back 30 degrees - so in the end 60. Started with 5 clicks from 0 and it didn't push the slug from the barrel, I ended up with +15 clicks with 223fps and stopped at this point as being scared that I will over tension the hammer again. I was hoping that I could increase the reg but keep the valve open for short period with small hammer spring tension. I don't know what is the max operating pressure for this regulator at which this gun can still hammer the valve and make it work (I know the minimal is 90 or it locks itself, also that if you dry fire it or the pressure will be below 90 you can damage the valve due to hammer as it won't be giving any resistance). However, is this gun able to be safely shot at reg 150 and I'm okay to tension the spring? At what point things are too much for it? I'm surprised there is no safety range, tolerances for spring hammer in this gun - to the point that you can tension it so much that it can damage the cocking lever and band it and cause it to shoot itself!
@@edgunwestLLC Iv put new indexing wheel in and Tower, all the plastic inserts in the lug and springs, New ball and i have put the butt on a working leshiy it fires mint but just will not index Could it be the valve is leaking too much air,(Valve the white thing that goes in the brass cage"
I. bought my R5 30 cal used from Edgun west and It had the Huma air regulator already installed. I’m getting 860fps with the 60gr NSA slugs. They are super accurate too! Seems ideal but sure doesn’t leave me much room for improvements lol! Mine is #245 of the 407 limited edition
I have the Edgun Meazy Gauge on my Leshiy 2 and and AirForce PCP but one of them keeps showing 3 stripes/dashes when "they wake up on shake". In the beginning the gauge showed the bottle pressure when I picket up the gun, but now it only shows 3 dashes. I have to unscrew the top and disconnect the battery for it to read the pressure again. Then it will work for a few times and the same thing occurs. I tried new batteries but thet doesn't fix the issue. You have any idea what this can be?
Hi Brian i have got the other reg in my Leshiy 2 and the reg does creep. If i set the reg to 100 bar overnight it creeps up to the bar thats in my tank can you help PLEASE!!!
Have the origional reg type leshiy 2 . When the reapr reg "upgrade" became standard in new models I decided to purchase the new style reg for almost $300 when it became available to purchase separately. Unfortunately I didn't even get to test it out in the field as it burst my first time filling it too only 200 bar.
@@edgunwestLLC The gauge stays at 200 or just below and im not leaving a 5 litre tank valve open while im looking at a needle ..You are willing to try it? ,See if you can get 5 litres in a 350cc tank
Ich musste diese Waffe wegen Mängeln zweimal zurückschicken. Das erste mal hat sie ständig Luft verloren, dass zweite mal drehte sich die Trommel nicht. Antwort vom Händler, diese Waffe ist etwas für Schraube, die haben Spaß damit. Also ich kaufe eine Waffe um damit zu schießen. Oder habe ich da was falsch verstanden. Mein Geld habe bereits zurückbekommen. Nie wieder Leshiy 2.
