If you are using your phone to record, once you properly get your item focused just hold your finger in the screen where you want it to focus until it locks your focus, then you don’t have to constantly try to refocus your video and we do t have to get a headache while our eyes try to constantly refocus on a blurry image.
I'm not using a phone to video. This video was about the time I stepped on my camera while replacing the oil pan gasket on the Ford Contour so I don't remember if I was using my old Sony camera or my Sony RX100. Both cameras are challenged when I try to get close to show you guys details. I don't always see the resolution from the small LED screen while I'm filming. Keeping details in focus is a challenge and will be until I upgrade to a new camera. The Sony can sure squeeze into some tight spaces. Thanks for watching!
Just got into ebay and found a listing for $15! This quick review was very helpful. Am wanting to dabble in photography so hearing this is great for beginners and takes actually good quality photos had me sold. Thanks for the review!
It's a great camera for beginners. You will learn a lot from watching how other photographers frame and light their photos. Best of luck and thanks for watching!
Fucking Stanley crap warranty. Sorry, I had a shit customer service experience this week. I'll never buy their garbage again but I'll try to fix my own box. Thanks for the video.
I have since replaced mine with a windshield mount (made by Torras) so I'm not blocking the air vent and the phone is in my line of sight. I made a video on the replacement. Thanks for watching!
I only used one of the bits one time. I could not honestly rate the hardness of the steel. They seemed robust but it would take a lot more use than I gave it to give them a full evaluation.
My fingerprint sensor came unplugged while doing this procedure (as well as the case shattering due to how strong the glue is). I can hide the cracks with a phone case protector, but how do I reconnect the fingerprint sensor (part to the left at 0:50) ?
If the plug isn't broken it should snap into place. It's so tiny that it's difficult to get into position. Use a magnifying glass or a lupe to watch it while your putting it in to place.
@@davidgpo I think the plug was broken but I was able to pressure fit it into place. Will have to keep an eye on how long the finger sensor works for now.
Capacity on our Fit is 3-1/2 quarts. When I add that amount during an oil change it never goes above the fill mark. Are you using the stock capacity oil filter? I suppose an oil filter smaller than specified can cause a higher reading on the dip stick. The stock filter is so small I don't think you can find one smaller?
I have a bread machine and I love mine. You need to have a different cup made for dry ingredients. The one you’re using is for wet ingredients. It does make a difference when you are baking. Good luck!
Thanks for sharing your video. My Sonic died last week. And I didn't want to buy a new one. I knew RU-vid had a video on battery replacement. And here we are. Now I just need to purchase a battery and get to work.
these jacks are high quality and if taken care of properly will last a lifetime. always turn counterclockwise until it stops and can't turn any more. Keep in mind the handle has to be in the up right position. Then til the handle and turn completely clockwise till it stops and can't turn any more. Now pump and when finish with the handle up turn and decompress the pump by turning the handle completely counter clockwise.
You would have killed a good battery like that you got to heat it quickly and solder the wire quickly for this you need a high power solder gun I’ve done it many times with 18650
I just reinstalled this unit in my 2nd car. This unit has been off unplugged for over 4 years. I powered it on and the time and date is still correct. But it won't connect to Android app and won't let me update firmware or software.
A few amatuerish mistakes here and there, but a Good video, and thanks for posting. To Identify a jack as Shinn Fu brand, look at the logo on the power unit ( see 21:50) Its like an N in a circle.
Hi I have a Vigo faucet too. I have replaced the handle twice and it’s broken again. This is poor design. I was wondering if had contacted the Vigo company ? If so Did they offer anything beside replacing the handle and collar?
Vigo's customer service was very poor. When I finally reached contact with a rep they told me it would take six months to get the part from China. I told them to order the part. They never asked for money. In the meantime I worked on repairing the faucet handle myself. As you can see be my various videos on this product it took me several tries to effect a permanent repair. When the part finally came in I ignored the messages from Vigo. Vigo offered nothing but trying to sell me another crappy handle! My repair is still holding up! Thanks for watching.